Table of Contents
Advertisement
Quick Links
Halogen Light Source with RS232 Intensity Control
HL-2000-HP-232
Installation and Operation Manual
Document Number 000-10000-140-02-1209
Offices:
E-mail:
000-00000-000-02-A
Ocean Optics, Inc. World Headquarters
830 Douglas Ave., Dunedin, FL, USA 34698
Phone
727.733.2447
Fax
727.733.3962
8 a.m.– 8 p.m. (Mon-Thu), 8 a.m.– 6 p.m. (Fri) EST
Ocean Optics Mikropack
Maybachstraße 11, D73760, Ostfildern, Germany
Phone
+49 (0)711 34 16 96-0
Fax
+49 (0)711 34 16 96-85
Info@OceanOptics.com
Info@Mikropack.de
Orders@OceanOptics.com
TechSupport@OceanOptics.com
(General sales inquiries)
(Mikropack sales inquiries)
(Questions about orders)
(Technical support)
Advertisement
Table of Contents
Related Manuals for Ocean Optics HL-2000-HP-232
Summary of Contents for Ocean Optics HL-2000-HP-232
- Page 1 Halogen Light Source with RS232 Intensity Control HL-2000-HP-232 Installation and Operation Manual Document Number 000-10000-140-02-1209 Offices: Ocean Optics, Inc. World Headquarters 830 Douglas Ave., Dunedin, FL, USA 34698 Phone 727.733.2447 727.733.3962 8 a.m.– 8 p.m. (Mon-Thu), 8 a.m.– 6 p.m. (Fri) EST Ocean Optics Mikropack Maybachstraße 11, D73760, Ostfildern, Germany...
- Page 2 Every effort has been made to make this manual as complete and as accurate as possible, but no warranty or fitness is implied. The information provided is on an “as is” basis. Ocean Optics, Inc. shall have neither liability nor responsibility to any person or entity with respect to any loss or damages arising from the...
- Page 3 Important Safety Notices 1. Read all safety and operating instructions before using this equipment. 2. Use this equipment in a clean, dry environment. Place the unit away from heat sources and ensure that nothing interferes with its ventilation. 3. Do not allow objects to fall, or liquids to spill into the unit through the enclosure openings. 4.
- Page 4 Important Safety Notices 000-10000-140-02-1209...
-
Page 5: Table Of Contents
Document Summary........................iii Product-Related Documentation ....................iii Upgrades ..........................iv Chapter 1: Setup...................1 Overview..........................1 Setting Up the HL-2000-HP-232 Light Source ..............1 Unpacking the Light Source ...................... 1 Package Contents ........................2 Set-Up............................2 Chapter 2: Operation ................5 Optimizing the Optical Power Output.................5 Shutter Diagram .........................6... - Page 6 Table of Contents Appendix B: HL-2000-HP-232 Specifications........15 Specifications ........................15 Parts List..........................16 Index ......................17 000-10000-140-02-1209...
-
Page 7: About This Manual
This document provides you with set-up and operation information to get your light source up and running. What’s New in this Document This version of the Halogen Light Source with RS232 Intensity Control HL-2000-HP-232 Installation and Operation Manual updates the logo and the contact information. Document Summary... -
Page 8: Upgrades
About This Manual Upgrades Occasionally, you may find that you need Ocean Optics to make a change or an upgrade to your system. To facilitate these changes, you must first contact Customer Support and obtain a Return Merchandise Authorization (RMA) number. Please contact Ocean Optics for specific instructions when returning a product. -
Page 9: Chapter 1: Setup
The attenuator and shutter can be controlled by a series of ASCII commands issued by a host computer via RS-232. Setting Up the HL-2000-HP-232 Light Source Unpacking the Light Source Procedure ►... -
Page 10: Package Contents
One 24 VDC 1,2A power supply HL-2000-HP-232 test software One Ocean Optics Software and Technical Resources CD In addition, you need an optical fiber (1000 μm diameter fiber is recommended). Set-Up Use the following procedure and diagrams to set up your light source. - Page 11 Notes The light can only be turned on via RS232 (see ). To test the light source, use the HL-2000-HP-232 test software included with your equipment. 6. Configure your computer’s COM port to establish connection with your light source. The COM...
- Page 12 1: Setup 000-10000-140-02-1209...
-
Page 13: Chapter 2: Operation
Optimizing the Optical Power Output The HL-2000-HP-232 is adjusted at the factory to provide maximum power into a 200µm fiber. If a lower optical power is required or a different fiber (bundle) diameter is used, you can adjust the optical power of the unit. -
Page 14: Shutter Diagram
2: Operation 3. Shift the SMA socket to optimize the optical power of the light source. 4. Tighten the blocking screw to secure the SMA socket position. Shutter Diagram 000-10000-140-02-1209... -
Page 15: Chapter 3: Bulb Replacement
Chapter 3 Bulb Replacement Overview To order replacement bulbs for the HL-2000-HP-232, consult the Parts List. WARNING Before replacing the bulb in the light source, disconnect the lamp from your power source and allow the unit to cool for at least twenty minutes, if necessary. - Page 16 3: Bulb Replacement 4. Loosen the hex screw on the lamp housing. 5. Remove the bulb by pulling it back away from the connector. 6. Replace the spare bulb with a new one. 7. Replace the hex screw on the lamp housing. 8.
-
Page 17: Appendix A: Ascii Commands
Appendix A ASCII Commands In serial communications mode, the motion controller is controlled via a series of ASCII instructions issued by a host computer. Motion-Related Commands Command Function Description Example Initiate Motion Receipt of the "M" Move command initiates motion using the values presently loaded to determine the profile characteristics. -
Page 18: Configuration-Related Commands
A: ASCII Commands Command Function Description Example Disable Drive Execution of this command disables the drive electronics and removes all current from the motor Enable Drive This instruction enables the drive electronics and allows the servo controller to become active, providing motor current as required. Load Position Range The range limit mechanism provides an LL 2000000... -
Page 19: External Limit Switch Configuration Commands
A: ASCII Commands Command Function Description Example Delayed Current Error This command sets the delay between current DCE 200 limit condition and setting the Fault-Status (Fault-Pin and Fault-Bit for the GFS- Command). The DCE argument is in milliseconds. Source For Velocity This command defines the source for the SOR 1 velocity of the motor. -
Page 20: Commands That Return Data
A: ASCII Commands Command Function Description Example Home Limit Action This command is used to set the action that HL 1 occurs when the limit switch is activated. If HL is set to 0, the motor will continue to run after switch activation but will send an "h"... - Page 21 A: ASCII Commands Command Function Description Example Get Real Current This command returns the current being used in milliamperes Get Status This command returns motion controller status. Description Bit 0: 1... Position mode 0... Velocity mode Bit 1: 1... Speed command is analog input 0...
- Page 22 A: ASCII Commands Command Function Description Example Get Version This command returns firmware version. GPOR Get Proportional Term This command returns Proportional gain setting GPOR 000-10000-140-02-1209...
-
Page 23: Appendix B: Hl-2000-Hp-232 Specifications
Appendix B HL-2000-HP-232 Specifications This section provides information on the operating environment, physical controls, and dimensions of the HL-2000-HP-232. It also provides a parts list. Specifications Specification Criteria Dimensions 70 mm x 100 mm x 160 mm Weight 600 g... -
Page 24: Parts List
B: HL-2000-HP-232 Specifications Parts List Spare Parts / Order Information Item Number Halogen high-power 20 W light source with RS232 control HL-2000-HP-232 Halogen spare bulb High-Power HL-2000-HP-B 000-10000-140-02-1209... -
Page 25: Index
Index ASCII commands, 9 optical power optimizing output, 5 bulb replacement, 7 package contents, 2 parts list, 16 product-related documentation, iii commands configuration-related, 10 data-returning, 12 external switch limit configuration, 11 setup, 1 motion-related, 9 setup procedure, 2 shutter diagram, 6 specifications, 15 document audience, iii... - Page 26 Index 000-10000-140-02-1209...
Need help?
Do you have a question about the HL-2000-HP-232 and is the answer not in the manual?
Questions and answers