Please check carefully to make sure there are no missing or defective parts - defective parts must never be used. B-Tech AV Mounts, its distributors and dealers are not liable or responsible for damage or injury caused by improper installation, improper use or failure to observe these safety instructions. In such cases, all guarantees will expire.
Page 3
A B-Tech AV Mounts recomenda que a instalação deste produto seja efectuada por um instalador de AV instalador de AV profissional ou outra pessoa devidamente habilitada. A B-Tech AV Mounts e os seus distribuidores e concessionários não são responsáveis por danos ou lesões causados por uma instalação incorrecta.
BT8563 PARTS LIST PLEASE KEEP THIS FOR FUTURE REFERENCE...
Page 5
PART NAME BASE CASTOR COLUMN MOUNTING BAR BALANCE BOX REAR COVER BALANCE BOX ADAPTOR PLATE MOUNTING PLATE INTERFACE ARM 600mm ADAPTOR ARM TRIM COLUMN CAP COLUMN REAR COVER COLUMN FRONT STRIP M8 x 35mm CSK SCREW SLIDING NUT M8 x 10mm SCREW M8 x 20mm SCREW M6 x 20mm SCREW M8 x 16mm CSK SCREW...
INSTALLATION INSTRUCTIONS FIX CASTORS TO BASE Screw 4 x item 2 into item 1 and apply the brakes. ATTACH COLUMN TO BASE Stand item 1 in its upright position. Insert item 3 into the cut out in item 1. Screw 4 x item 15 through the underside of item 1 into item 3.
ATTACH MOUNTING BARS TO COLUMN i. Slide 8 x item 16 into the front slots of item 3. ii. Attach item 4 to item 3 using 4 x item 17 fastening into item 16. Mount one item 4 approx 10mm from the top of item 3 and the other item 4, 433mm below. INSERT BALANCE BOX MOUNTING SCREWS Insert 2 x item 18 into the top item 4.
INSERT BALANCE BOX REAR COVER Insert item 5 into the slots on the left and right side of item 6. TOP VIEW Rear of item 6 SLOT SLOT HOOK ON BALANCE BOX Hook item 6 onto item 18 using the keyhole fixings on the rear of item 6. KEYHOLE...
Page 9
LEVEL BALANCE BOX Using a crosshead screwdriver and a spirit level, adjust the levelling screws on the front of item 6 until the balance box is level. LEVELLING SCREW LEVEL FIX BALANCE BOX Fix item 6 to the bottom item 4 using item 19. Insert item 19 through these holes .
Using 600mm adaptor arms FIXING INTERFACE ARMS TO SCREEN i) Attach item 10 to item 9 Fix items 9 to the back of the screen using the interface kit (items A-M). with items 23. Note: Ensure items 9 are positioned the correct way round. Portrait mounting assembly shown ii) Attach item 10 to rear of screen using the interface kit (items A-L).
Page 12
SCREEN ADJUSTMENT To level the screen, use the height adjustment screws at the top of item 9, using item 24. SCREEN SCREEN HEIGHT ADJUSTMENT SCREW LOCK SCREEN ONTO MOUNTING PLATE Lock screen onto item 8 using the locking screws at the bottom of item 9. SCREEN LOCKING SCREW SCREEN...
Page 13
BALANCE SCREEN TO ENABLE HEIGHT ADJUSTMENT To balance the screen use a drill driver at low torque setting and a 10mm socket. i. Turn the left spring tension point counter-clockwise for 5 seconds. ii. Turn the right spring tension point counter-clockwise for 5 seconds. iii.
ATTACH PLASTIC COVERS i. Attach items 13 to the rear of item 3. ii. Fit item 12 to the top of item 3. SCREEN iii. Fit item 11 to the front and rear of item 1. INSERT COLUMN STRIPS CABLE MANAGEMENT Insert item 14 into the front slots on item 3.
269.9mm 620mm 869.2mm BACK VIEW TOP VIEW 572mm 225mm 30mm 1074.4mm HEIGHT OPTIONS Maximum Height Minimum Height THESE INSTRUCTIONS ARE INTENDED AS A GUIDE ONLY AND B-TECH ACCEPTS NO LIABILITY FOR THE ACCURACY OF THE INFORMATION CONTAINED IN THIS DOCUMENT.