Page 1
Uni-9 Series Operation Manual PN 174357 January 27 2016...
Page 3
NOTICES NOTICES IMPORTANT NOTICE Those who handle the machine must be aware of the hazards involved. These dangers may not be obvious, so it is imperative to follow the instructions detailed in this manual when installing, operating, inspecting, or servicing the machine. Therefore, we recommend that you thoroughly read and understand this manual before installing, operating, inspecting, or servicing the machine.
Page 4
PRECAUTIONS FOR SAFE USE PRECAUTIONS FOR SAFE USE It is strongly advised that the following safety measures must be observed to ensure the safe operation of the machine. • Prepare a dedicated power source and always use a power supply with rated voltage. Never connect the machine power input with an AC power supply exceeding the rated voltage.
Page 5
PRECAUTIONS FOR SAFE USE • Do not hold the connector cover when carrying the machine. Dropping the machine may result in injury or cause the machine to break down. • Do not hold the operation panel or weigh platter when carrying the machine. Doing so may cause the operation panel or the platter to break down.
Page 6
PRECAUTIONS FOR SAFE USE • Risk of explosion if battery is replaced by an incorrect type. Make sure to dispose of used batteries according to the instructions. UNI-9 User’s Manual...
Page 7
PRECAUTIONS FOR SAFE USE PRECAUTIONS FOR MACHINE INSTALLATION Do not install the machine in the following types of places: • • • Places subject to high Places subject to excessive Places subject to a lot of dust or temperatures or high humidity vibration or unstable foundations dirt •...
Page 8
PRECAUTION SYMBOLS PRECAUTION SYMBOLS This machine is manufactured for use according to proper procedures by a qualified person and only for the purposes described in this manual. The following conventions are used to indicate and classify precautions depending on the level of danger, or seriousness of potential injury. Always heed the information provided in this manual.
Chapter 1: BEFORE USE BEFORE USE 1.1 specifications UNIT ITEM DESCRIPTIONS Weighing unit Weighing capacity 6 kg specification: 0 to 3 kg / 1 g, 3 to 6 kg / 2 g Weighting accuracy 1/3000 8.4 inch color TFT liquid crystal display with LED Operation panel unit Display method backlight, Screen resolution SCGA (800 X 600 dots)
Chapter 1: BEFORE USE 1.3 Level Adjustment Install the machine horizontally to use. Be sure to turn off the power switch before placing the machine on a stable platform, and adjust the machine inclination by turning the four level adjustment legs so that the bubble is located at the center of the level gauge. Accurate measurements cannot be performed if it is not installed horizontally.
Chapter 1: BEFORE USE 1.4 label / receipt roll Loading Pull out the cassette from the main body. Before pulling out the cassette unit, ensure that nothing is placed on the weighing platter. Set a new roll around the roll holder and raise the roll stopper to fix the roll position. Roll stopper Label roll Roll holder...
Page 16
Chapter 1: BEFORE USE For labels, fix the paper end with the backing paper stopper, and gently turn the winding bobbin clockwise until the label becomes tight. Winding bobbin Slide the label/receipt guide to help smooth paper feeding according to the paper width. Label / Receipt guide Push the cassette straight into the main body to return to its original position.
Chapter 1: BEFORE USE 1.5 removing & replacing of weighing platter 1.5.1 REMOVING THE WEIGHING PLATTER When removing the weighing platter from the main body, lift the front side to pull out the two pins from the two rubber platter holders and remove the platter by pulling it to disengage the two hooks at the rear side of the platter.
Chapter 1: BEFORE USE 1.6 Cleaning of the machine 1.6.1 CLEANING OF THE THEREMAL HEAD Pull out the cassette from the main body. Before pulling out the cassette unit, ensure that nothing is placed on the weighing platter. Use a cotton-tipped swab to clean off the thermal head. Uni-9 User’s Manual...
Chapter 1: BEFORE USE 1.6.2 CLEANING OF THE LABEL SENSOR Pull out the cassette from the main body. Before pulling out the cassette unit, ensure that nothing is placed on the weighing platter. Use a dry cloth to clean off the emitter and receiver of the label sensor. Uni-9 User’s Manual...
Chapter 1: BEFORE USE 1.6.3 CLEANING OF THE PRINT ROLLER AND PRISM Pull out the cassette from the main body. Before pulling out the cassette unit, ensure that nothing is placed on the weighing platter. Use a dry cloth to clean off the print roller and prism. Uni-9 User’s Manual...
Chapter 1: BEFORE USE 1.6.4 PRECAUTIONS WHEN USING CLEANING FLUIDS Use a soft cloth and a neutral detergent to clean the machine. Do not use thinner, benzene, etc. Doing so may damage the original safety functions. For some parts, use cleaning fluid (isopropyl alcohol). ...
Chapter 1: BEFORE USE STARTING PROCEDURES 1.7.1 TURNING ON THE POWER Push down the Power Switch to turn on the The “Clock Check” screen is displayed. power. Check that displayed date and time agree with the current date and time, and press the [ENTER] button on the screen to proceed to the next step.
Chapter 1: BEFORE USE 1.7.2 ZERO ADJUSTMENT If the “ZERO” indicator does not appear in the The “ZERO” indicator lights up and the “WEIGHT” field on the initial screen, press weight value becomes zero. the [ZERO] key. 1.7.3 GETTING BACK TO THE INITIAL SCREEN To get back to the initial screen from a Menu The initial screen is displayed.
Chapter 2: OPERATION MODE OPERATION MODE OPERATION MODE ENTRY / EXIT Ensure that the initial screen is displayed. Then, press the Return button to display the “Menu” screen. Note: The contents of the initial screen may differ depending on the settings on your machine. The “Menu”...
Chapter 2: OPERATION MODE SALES OPERATIONS 2.3.1 ISSUING LABELS FOR WEIGHING PRODUCTS Press the “SALES” icon on the operation The initial screen is displayed. menu selection screen. Note: The contents of the initial screen may differ depending on the settings on your machine. Enter a PLU number and press the [PLU] key Press a preset product department key to on the keypad.
Page 28
Chapter 2: OPERATION MODE The designated weighing PLU screen is Put the product on the weighing platter. displayed. EXAMPLE A product to which its unit price and tare weight were set beforehand. The product is weighed and its total price is calculated.
Chapter 2: OPERATION MODE 2.3.2 ISSUING LABELS FOR WEIGHING FIXED PRICE PRODUCTS Press the “SALES” icon on the operation The initial screen is displayed. menu selection screen. Note: The contents of the initial screen may differ depending on the settings on your machine. Enter a PLU number and press the [PLU] key Press a preset product department key to on the keypad.
Page 30
Chapter 2: OPERATION MODE The designated weighing PLU screen is Put the product on the weighing platter. displayed. EXAMPLE A product to which its tare weight and price were set beforehand. The product is weighed, but its price stays the same. Press the [PRINT] key to issue a label when “MANUAL”...
Chapter 2: OPERATION MODE 2.3.3 ISSUING LABELS FOR FIXED PRICE PRODUCTS Press the “SALES” icon on the operation The initial screen is displayed. menu selection screen. Note: The contents of the initial screen may differ depending on the settings on your machine. Enter a PLU number and press the [PLU] key Press a preset product department key to on the keypad.
Page 32
Chapter 2: OPERATION MODE The designated non-weighing PLU screen is Press the [PRINT] key to issue labels when displayed. “MANUAL” is set in the “Print Mode” field. Note: Labels are automatically issued when “AUTO” is set in the “Print Mode” field. Non-traceable products Traceable products Note: To stop printing, press the [PRINT] key again.
Chapter 2: OPERATION MODE 2.3.4 ISSUING LABELS FOR FIXED WEIGHT/UNIT PRICE PRODUCTS Press the “SALES” icon on the operation The initial screen is displayed. menu selection screen. Note: The contents of the initial screen may differ depending on the settings on your machine. Enter a PLU number and press the [PLU] key Press a preset product department key to on the keypad.
Page 34
Chapter 2: OPERATION MODE The designated non-weighing PLU screen is Enter the fixed weight and press the “FIXED displayed. WEIGHT” field. EXAMPLE Fixed weight “159 g” Non-traceable products Traceable products Note: To stop printing, press the [PRINT] key again. UNI-9 User’s Manual 2-11...
Chapter 2: OPERATION MODE 2.3.5 ISSUING LABELS REQUIRING OPERATOR REGISTRATION Press the “SALES” icon on the operation The initial screen is displayed. menu selection screen. Note: The contents of the initial screen may differ depending on the settings on your machine. Enter a PLU number and press the [PLU] key Press a preset product department key to on the keypad.
Page 36
Chapter 2: OPERATION MODE The designated PLU screen is displayed. Put the product on the weighing platter. EXAMPLE A product to which its unit price and tare weight were set beforehand. The product is weighed and its total price is calculated.
Chapter 2: OPERATION MODE 2.3.6 ISSUING RECEIPTS BY THE SAME OPERATOR Ensure that the “Operator Selection” screen The initial screen is displayed. is displayed. Note: The contents of the initial screen may differ Then, press an operator button for selection. depending on the settings on your machine.
Page 38
Chapter 2: OPERATION MODE The designated weighing PLU screen is Put the product on the weighing platter. displayed. Press the [SUB TOTAL] key to complete the The subtotal screen for the designated registration. operator appears on the screen. Select a product department by pressing the The PLU preset key screen associated to the corresponding field.
Page 39
Chapter 2: OPERATION MODE Press [] to complete the registration. Select a product department by pressing the The PLU preset key screen associated to the corresponding field on the screen. designated department is displayed. Then, press the preset PLU key where the EXAMPLE “VEGETABLES”...
Page 40
Chapter 2: OPERATION MODE Press the [SUB TOTAL] button. The subtotal screen for the designated operator is displayed. Select a product department by pressing the The PLU preset key screen associated to the corresponding field on the screen. designated department is displayed. Then, press the preset PLU key where the EXAMPLE “VEGETABLES”...
Page 41
Chapter 2: OPERATION MODE Press the [SUB TOTAL] button. The subtotal screen is displayed. Press the operator field to display more The detailed subtotal screen is displayed. detailed subtotal data. Then, confirm that the details of the displayed transaction are correct. UNI-9 User’s Manual 2-18...
Page 42
Chapter 2: OPERATION MODE Press the [PRINT] key to issue a receipt. The subtotal screen is displayed. UNI-9 User’s Manual 2-19...
Chapter 2: OPERATION MODE 2.3.7 ISSUING RECEIPTS BY DIFFERENT OPERATORS Ensure that the initial screen is displayed. Note: The contents of the initial screen may differ depending on the settings on your machine. Enter a PLU number and press the [PLU] key Press a preset product department key to on the keypad.
Page 44
Chapter 2: OPERATION MODE The designated PLU screen is displayed. Put the product on the weighing platter. Press an operator button. The subtotal screen for the designated operator is displayed. EXAMPLE Operator “BETTY” Select a product department by pressing the The PLU preset screen associated to the corresponding field on the screen.
Page 45
Chapter 2: OPERATION MODE The designated PLU screen is displayed. Press an operator button. EXAMPLE Operator “BETTY” The subtotal screen for the designated Now, the operator has changed from operator is displayed. “BETTY” to “JACK”. Select a product department by pressing the corresponding field on the screen.
Page 46
Chapter 2: OPERATION MODE Put the product on the weighing platter. Press an operator button. EXAMPLE Operator “JACK” The subtotal screen for the designated Now, “BETTY” is back again. operator is displayed. Select a product department by pressing the corresponding field on the screen. EXAMPLE “VEGETABLES”...
Page 47
Chapter 2: OPERATION MODE Enter the weight value, and press the “Fixed Press an operator button. Weight” field. EXAMPLE Operator “BETTY” EXAMPLE Weight “159 g” The subtotal screen for the designated Press the operator field to display more operator is displayed. detailed subtotal data.
Page 48
Chapter 2: OPERATION MODE Press the [PRINT] key to issue a receipt. The subtotal screen is displayed. UNI-9 User’s Manual 2-25...
Chapter 2: OPERATION MODE 2.3.8 VOIDING PRODUCT REGISTRATIONS To void a product registration that has been Press the field of a product registration to be made in the transaction, display the voided, and then press the [VOID] button. “Sub-Total” screen. EXAMPLE Voiding the third registration...
Page 50
Chapter 2: OPERATION MODE Press the [PRINT] key to issue a receipt. The subtotal screen is displayed. Deleted by a dashed line UNI-9 User’s Manual 2-27...
Chapter 2: OPERATION MODE 2.3.9 ENTERING OR OVERWRITING TARE WEIGHTS Ensure that the designated PLU screen is Enter a numerical value and press the displayed. [T] (Tare) key. EXAMPLE Tare weight “50 g” 2.3.10 CHANGING UNIT PRICES Ensure that the designated PLU screen is Enter the unit price and press the “UNIT displayed.
Chapter 2: OPERATION MODE 2.3.11 CHANGING FIXED PRICES Ensure that the designated PLU screen is Enter the price, and press the “FIXED displayed. PRICE” field. EXAMPLE “$1.56” Fixed Price Products 2.3.12 DISCOUNTING UNIT PRICES BY AMOUNT Ensure that the designated PLU screen is Enter the amount to be discounted, and displayed.
Chapter 2: OPERATION MODE 2.3.13 DISCOUNTING UNIT PRICES BY PERCENTAGE Ensure that the designated PLU screen is Enter the discount percentage, and press the displayed. “-% (U/P)” field. EXAMPLE Discount percentage “10%”. 2.3.14 DISCOUNTING TOTAL PRICES BY AMOUNT Ensure that the designated PLU screen is Enter a discount amount using the numeric displayed.
Chapter 2: OPERATION MODE 2.3.15 DISCOUNTING TOTAL PRICES BY PERCENTAGE Ensure that the designated PLU screen is Enter the discount percentage, and press the displayed. “-%” field. EXAMPLE Discount percentage “10%”. 2.3.16 CHANGING QUANTITIES Ensure that the designated price PLU screen Enter the quantity and press the [X] key.
Chapter 2: OPERATION MODE 2.3.17 SPECIFYING THE NUMBER OF LABELS Ensure that the designated PLU screen is Enter the number of labels to be printed and displayed, and confirm that “AUTO” is press the [PRINT] key to print labels. . selected in the “Print Mode”...
Chapter 2: OPERATION MODE 2.3.18 SELF-SERVICE OPERATIONS FOR WEIGHING PRODUCTS Ensure that the initial screen for self-service Select a product by pressing the operations is displayed. corresponding field on the screen. EXAMPLE “Red Grape” (weighing product) The designated product image is displayed. Put the product on the weighing platter.
Chapter 2: OPERATION MODE 2.3.19 SELF-SERVICE OPERATIONS FOR FIXED PRICE PRODUCTS Ensure that the initial screen for self-service Select a product by pressing the operations is displayed. corresponding field on the screen. EXAMPLE “APPLE ROYAL” The designated product image is displayed. Enter the quantity and press the [MULTI] key.
Chapter 2: OPERATION MODE 2.3.20 ACCUMULATIONS THROUGH MANUAL ENTRY Ensure that the operation menu selection The “Input Numerical Accumulation” screen screen is displayed. is displayed. Then, press the “ACC (Accumulation)” icon. Press the input field at the right-bottom of the The “Input Numerical Accumulation”...
Page 60
Chapter 2: OPERATION MODE The accumulation procedure has been completed. UNI-9 User’s Manual 2-37...
Chapter 2: OPERATION MODE 2.3.21 ACCUMULATIONS THROUGH WEIGHING PRODUCTS Ensure that the operation menu selection The “Input Numerical Accumulation” screen screen is displayed. is displayed. Then, press the “ACC (Accumulation)” icon. Press the “WGT. ACC” tab to display the Press the input field at the right-bottom of the “Weighing Accumulation”...
Page 62
Chapter 2: OPERATION MODE The confirmation screen is displayed. Remove the product from the weighing Press [EXEC] to continue, or [STOP] to go platter. back. The accumulation procedure has been completed. UNI-9 User’s Manual 2-39...
Chapter 2: OPERATION MODE 2.3.22 VOIDING REGISTRATIONS THROUGH MANUAL ENTRY Ensure that the operation menu selection The “Input Numerical Accumulation” screen screen is displayed. is displayed. Then, press the “ACC (Accumulation)” icon. Press the “NUM. VOID” tab to display the Press the input field at the right-bottom of the “Input Number Void”...
Page 64
Chapter 2: OPERATION MODE The confirmation screen is displayed. The void procedure has been completed. Press [EXEC] to continue, or [STOP] to go back. UNI-9 User’s Manual 2-41...
Chapter 2: OPERATION MODE 2.3.23 VOIDING THROUGH WEIGHING PRODUCTS Press the “ACC (Accumulator)” icon. The “Input Number Accumulation” screen is displayed. To display the “Weighing Void” screen, press Press the input field at the right-bottom of the the “WGT. VOID” tab. screen to display the keypad.
Page 66
Chapter 2: OPERATION MODE The confirmation screen is displayed. Remove the product from the weighing Press [EXEC] to continue, or [STOP] to go platter. back. The void procedure has been completed. UNI-9 User’s Manual 2-43...
Chapter 2: OPERATION MODE 2.3.24 SUBTRACTING TOTALS THROUGH MANUAL ENTRY Press the “TOTAL ADJUST” icon. The “Total Adjust (Input Number Subtraction)” screen is displayed. Press the input field at the right-bottom of the The Total Adjust (Input Number Subtraction) screen to display the keypad. screen for the selected product is displayed.
Page 68
Chapter 2: OPERATION MODE The subtraction procedure has been completed. UNI-9 User’s Manual 2-45...
Chapter 2: OPERATION MODE 2.3.25 SUBTRACTING TOTALS THROUGH WEIGHING PRODUCTS Press the “TOTAL ADJUST” icon. The “Total Adjust (Input Number Subtraction)” screen is displayed. To display the “Total Adjust (Weighing Press the input field at the right-bottom of the Subtraction)” screen, press the “WGT. SUB” screen to display the keypad.
Page 70
Chapter 2: OPERATION MODE The confirmation screen is displayed. Remove the product from the weighing Press [EXEC] to continue, or [STOP] to go platter to complete the subtraction procedure. back. UNI-9 User’s Manual 2-47...
Chapter 2: OPERATION MODE 2.3.26 ADDING TOTALS THROUGH MANUAL ENTRY Press the “TOTAL ADJUST” icon. The “Total Adjust (Input Number Subtraction)” screen is displayed. To display the “Total Adjust (Input Number Press the input field at the right-bottom of the Addition)”...
Page 72
Chapter 2: OPERATION MODE The confirmation screen is displayed. The addition procedure has been completed. Press [EXEC] to continue, or [STOP] to go back. UNI-9 User’s Manual 2-49...
Chapter 2: OPERATION MODE 2.3.27 ADDING TOTALS THROUGH WEIGHING PRODUCTS Press the “TOTAL ADJUST” icon. The “Total Adjust (Input Number Subtraction)” screen is displayed. To display the “Total Adjust (Weighing Add)” Press the input field at the right-bottom of the screen, press the [WGT.
Page 74
Chapter 2: OPERATION MODE The confirmation screen is displayed. Remove the product from the weighing Press [EXEC] to continue, or [STOP] to go platter to complete the addition procedure. back. UNI-9 User’s Manual 2-51...
Chapter 3: TOTAL MODE TOTAL MODE 3.1 total MODE ENTRY / exit Make sure that the initial screen is displayed. Press the [TOTAL] button. Then, press the Return button on the screen to display the “Menu” screen. Note: The contents of the initial screen may differ depending on the settings on your machine.
Chapter 3: TOTAL MODE DAILY TOTALS The total menu selection screen is The “Production Daily Total (Total)” screen displayed. is displayed. To display the “Production Daily Total To display the “Production Daily Total (Hourly)” screen, press the “HOUR” tab. (Department)” screen, press the “DEPT.” ...
Page 77
Chapter 3: TOTAL MODE To display the “Production Daily Total To display the “Production Daily Total (PLU)” (Group)” screen, press the “GROUP” tab. screen, press the “PLU” tab. Press the input field at the right-bottom of the screen to display the keypad. Then, enter a desired PLU number and press the [PLU] key on the keypad.
Page 78
Chapter 3: TOTAL MODE Select the target reports by pressing a Select the listing order by pressing a desired desired button. button. The total analysis is performed for all products. DEPT. The total analysis is performed for all departments. GROUP The total analysis is performed for all groups.
Chapter 3: TOTAL MODE WEEKLY TOTALS Press the “PROD. WEEKLY” icon. The Weekly Total (Week) screen is displayed. To display the “Production Weekly Total” total for the day-of-the week, press a desired day-of-the week tab. To turn pages, press the [ ] or [ ...
Chapter 3: TOTAL MODE CUMULATIVE TOTALS Press the “PROD. CUM. TOTAL” icon. The “Cumulative Total (Total) screen is displayed. To display total for departments, press the To display total for groups, press the “DEPT.” tab. “GROUP” tab. To display total for operators, press the To display analysis totals, press the “TYPE”...
Page 81
Chapter 3: TOTAL MODE Z PRICE The total analysis is performed in ascending price order. Z WEIGHT The total analysis is performed in ascending weight order. Z PCS The total analysis is performed in ascending quantity order. Select the target reports and listing order by pressing desired buttons, and press the [ANALYSIS] button.
Chapter 3: TOTAL MODE TRACEABILITY TOTALS Press the “TRACE. TOTAL” icon. For more information, refer to the Service Manual for UNI-9. UNI-9 User’s Manual...
Chapter 3: TOTAL MODE PRESET REPORTS Press the “PRESET REPORT” icon. The “Preset Report” screen is displayed. Select a desired report type by pressing the corresponding fields. Press the [PRINT] button to issue the selected reports. UNI-9 User’s Manual...
Chapter 3: TOTAL MODE TOTAL CLEAR Press the “TOTAL CLEAR” icon. The “Total Clear” screen is displayed. Select desired reports to be cleared by The confirmation screen is displayed. pressing the corresponding fields. Press [EXEC] to continue, or [STOP] to go Then, press the [DELETE] button.
Chapter 4: PROGRAM MODE PROGRAM MODE 4.1 program MODE ENTRY / exit Ensure that the initial screen is displayed, The “Menu” screen is displayed. and press the Return button on the screen. Then, press the [PROGRAM] button. Note: The contents of the initial screen may differ depending on the settings on your machine.
Chapter 4: PROGRAM MODE PLU DATA Press the “PLU” icon on the menu selection The “PLU” screen is displayed. screen. To turn pages, press [ ] or [ Select a desired PLU by pressing the The “PLU Detail (Sales)” screen is displayed. corresponding field, and press the [DETAIL] To edit the PLU name, press the name field.
Page 87
Chapter 4: PROGRAM MODE Press [<] or [>] to select a desired sales mode. 0: Weight (for selling weighing products) 1: Fix price (for selling fixed price products) 2: Weight fix price (for selling weighing fixed price products) SALES MODE 3: Fix unit price (for selling fixed unit price products) 4: Weight (100 g) (when the setting of the unit price per 100 g is needed in accordance of the laws of a country)
Page 88
Chapter 4: PROGRAM MODE Press the “UNIT TYPE” field to display the “Fix Price Symbol” screen. Then, press a desired field for selection. UNIT TYPE Enter the packed quantity and press this field. Enter the tare percentage and press this field. TARE Enter the lower weight limit and press this field.
Page 89
Chapter 4: PROGRAM MODE ITEM DESCRIPTIONS Press [<] or [>] to select whether or not to use the point flag. POINT FLAG 0: OFF 1: ON Press [<] or [>] to select a desired point type. POINT TYPE 0: Weight 1: Fixed weight POINTS Enter a desired number and press this field.
Page 90
Chapter 4: PROGRAM MODE The selected image has been registered. The “Image” screen is displayed. Press [NO PRINT] or [PRINT] in the “Safe Press a desired image for selection. Handling Image” field to select whether or not to print the image. Press a desired display image field.
Page 91
Chapter 4: PROGRAM MODE The selected image has been registered. Press [NO PRINT] or [PRINT] in the “Safe Handling Image” field to select whether or not to print the image. Press the “PRINT” tab to display the PLU / Detail (Print) screen. ITEM DESCRIPTIONS 1st LABEL FORMAT...
Page 92
Chapter 4: PROGRAM MODE Press the “DATE” tab to display the PLU / Detail (Date) screen. ITEM DESCRIPTIONS Press [YES] or [NO] in this field to select whether or not to print the packed PACK DATE PRINT date. Press [<] or [>] to select a desired pack time printing method. 0: No print PACK TIME PRINT 1: Designated time...
Page 93
Chapter 4: PROGRAM MODE TIME PRINT”. Enter the time and press this field. Press [YES] or [NO] in this field to select whether or not to print the sell-by SB DATE PRINT date. Press [<] or [>] to select a desired sell-by time printing method. 0: No print SB TIME PRINT 1: Designated time...
Page 94
Chapter 4: PROGRAM MODE REG CODE Enter the register code and press this field. This field is available only when “1: PLU File” is selected in “POS POS FLAG REFERENCE”. Enter a POS flag number and press this field. BARCODE Enter a barcode number and press this field.
Page 95
Chapter 4: PROGRAM MODE Press [YES] or [NO] in this field to select whether or not to enable a TRACE ENABLE traceability function. Press this field to display the Department screen. DEPARTMENT No. To set a department, press a desired field on the list, or press the “DEPARTMENT No.”...
Chapter 4: PROGRAM MODE CAMPAIGN DATA The “Campaign” screen is displayed. Press the “CAMPAIGN” icon on the menu To create the first data, press the [NEW] selection screen. button. To change existing data, press a desired field To call up desired data, press the Input field for selection and then the [DETAIL] button.
Page 97
Chapter 4: PROGRAM MODE The PLU screen is displayed. The designated “Campaign / Detail (Data)” Press a desired item field for selection. screen is displayed. Press the “MD MODE” field. The Campaign / Mode List screen is displayed. Press a desired field for selection. EXAMPLE Percent discount “-%”...
Page 98
Chapter 4: PROGRAM MODE 4-14 UNI-9 User’s Manual...
Chapter 4: PROGRAM MODE 4.4 OPerator data Press the “OPERATORS” icon on the menu The “Operator” screen is displayed. selection screen. To call up desired data, press the Input field at the bottom right of the screen to display the keypad. Then, enter a numerical value and press the [PLU] key on the keypad.
Page 100
Chapter 4: PROGRAM MODE To finish the editing, press the Return button. To set a password, press the Input field at the bottom right of the screen to display the keypad. Enter the 4-digit numerical value and press the [SET] key on the keypad, and then press the “PASSWORD”...
Page 101
Chapter 4: PROGRAM MODE The edited data has been registered. 4-17 UNI-9 User’s Manual...
Chapter 4: PROGRAM MODE PRESET KEY REGISTRATION 4.5.1 SETTING PRESET GROUPS AND PAGES The Preset Key screen is displayed. Press the “PRESET KEY” icon on the menu Press a desired field for selection, and press selection screen. the [DETAIL] button. The edit screen is displayed.
Chapter 4: PROGRAM MODE 4.5.2 SETTING PRESET KEYS The “Preset Key” screen is displayed. Press the “PRESET KEY” icon on the menu Press a desired field for selection, and press selection screen. the [DETAIL] button. Select the group and the page where you Available preset keys are listed on the screen.
Page 104
Chapter 4: PROGRAM MODE Press a desired function for selection. EXAMPLE Selecting the PLU function The PLU screen is displayed. The selected preset key has been assigned. Press a desired field for selection. EXAMPLE PLU No.3 4-20 UNI-9 User’s Manual...
Page 105
Chapter 4: PROGRAM MODE 4-21 UNI-9 User’s Manual...
Chapter 4: PROGRAM MODE 4.5.3 CHANGING PRESET KEY SIZES AND POSITIONS The “Preset Key” screen is displayed. Press the “PRESET KEY” icon on the menu Press a desired field for selection, and press selection screen. the [DETAIL] button. Select the group and the page that the preset The size and position editing screen is key you want to edit is located, and then displayed.
Chapter 4: PROGRAM MODE 4.5.4 EDITING PRESET KEYS The “Preset Key” screen is displayed. Press the “PRESET KEY” icon on the menu Press a desired field for selection, and press selection screen. the [DETAIL] button. Select the group and the page that the preset The editing screen is displayed.
Page 108
Chapter 4: PROGRAM MODE To change the font size, press the “TITLE The font size has been changed. FONT” or ”FONT” field, enter a numerical value, and press the [SET] button on the keypad. Enter To change the preset key title, press the The “Preset Key / Name Edit”...
Page 109
Chapter 4: PROGRAM MODE To assign a desired image to the preset key, The Preset Key / Image screen is displayed. press the “IMAGE No.” field. Press a desired image for selection. Note: To use images stored in the USB memory, press [STORAGE] key.
Page 110
Chapter 4: PROGRAM MODE Press a desired color for selection. The selected color has been applied to the background of the key. To change the font color, press the “UPPER Press a desired color for selection. TEXT” or “LOWER TEXT” field. The selected color has been applied to the To change the preset key operation, press the text on the key.
Page 111
Chapter 4: PROGRAM MODE Available functions are listed on the screen. To change the PLU number called up by the for selection Press a desired function preset key, press the “DATA” field. Upon completion of all settings, press the Return The PLU screen is displayed.
Chapter 4: PROGRAM MODE 4.5.5 DELETING PRESET KEYS The “Preset Key” screen is displayed. Press the “PRESET KEY” icon on the menu Press a desired field for selection, and press selection screen. the [DETAIL] button. Select the group and the page that the preset The selected key has been deleted.
Chapter 4: PROGRAM MODE ADVERTISEMENT MESSAGES Press the “AD MSG.” icon on the menu The “Advertisement Message” screen is selection screen. displayed. To create the first data, press the [NEW] button. To change existing data, press a desired field To call up desired data, press the Input field for selection and then the [DETAIL] button.
Page 114
Chapter 4: PROGRAM MODE The “Advertisement Message / Detail / Edit” To exit the edit mode, press the Return button. screen is displayed. Edit a desired message according to the procedure described in Appendix “Text Editing”. The confirmation screen is displayed. To confirm changes, press [SAVE].
Page 115
Chapter 4: PROGRAM MODE The “Advertisement Message / Detail (Text)” screen is displayed. ITEM DESCRIPTIONS Press [<] or [>] to select a desired display type. 0: None TEXT DISPLAY TYPE 1: Slide 2: Flash Press [<] or [>] to select a desired display type. 0: None IMAGE DISPLAY TYPE 1: Slide...
Page 116
Chapter 4: PROGRAM MODE Press the “IMAGE” tab to display the Press a desired field to display the Image “Advertisement Message / Detail (Image)” screen. screen. The selected image has been assigned in The “Advertisement Message / Image” the designated field. screen is displayed.
Chapter 4: PROGRAM MODE SCHEDULE DATA Press the “SCHEDULER” icon on the menu To call up a desired data number, press the selection screen. Input field at the bottom right of the screen to display the keypad. Then, enter a desired numerical value and press the [PLU] key on the keypad.
Page 118
Chapter 4: PROGRAM MODE To enter the end date, press the “END DATE” To enter the start time, press the “START field, enter a numerical value, and press the TIME” field, enter a numerical value, and [SET] key on the keypad. press the [SET] key on the keypad.
Chapter 4: PROGRAM MODE STORE DATA Press the “STORE” icon on the menu The “Store” screen is displayed. selection screen. To call up desired data, press the Input field at the bottom right of the screen to display the keypad. Then, enter a numerical value and press the [PLU] key on the keypad.
Page 120
Chapter 4: PROGRAM MODE The “Store / Detail” screen is displayed. The “Store / Name Edit” screen is displayed Press the name field. for the selected store number. Edit text according to the procedure described in Appendix “Text Editing”. Press the Return button to finish the editing. The confirmation screen is displayed.
Page 121
Chapter 4: PROGRAM MODE The “Store / Edit Address” screen is Press the Return button to finish the editing. displayed. Edit text according to the procedure described in Appendix “Text Editing”. The store address has been registered. The confirmation screen is displayed. To confirm changes, press [SAVE].
Chapter 4: PROGRAM MODE 4.9 department name data Press the “DEPARTMENT” icon on the The “Department” screen is displayed. menu selection screen. To create the first data, press the [NEW] button. To change existing data, press a desired field To call up desired data, press the Input field for selection and press the [DETAIL] button.
Page 123
Chapter 4: PROGRAM MODE The confirmation screen is displayed. Press the Return button to finish the editing. To confirm changes, press [SAVE]. To undo changes, press [CANCEL]. The edited data has been registered. 4-39 UNI-9 User’s Manual...
Chapter 4: PROGRAM MODE 4.10 group name data Press the “GROUP” icon on the menu The “Group” screen is displayed. selection screen. To create the first data, press the [NEW] button. To change existing data, press a desired field To call up desired data, press the Input field for selection and then the [DETAIL] button.
Page 125
Chapter 4: PROGRAM MODE Press the Return button to finalize the edited The confirmation screen appears. text. Press [EXEC] to continue, or [STOP] to go back. The edited data has been registered. 4-41 UNI-9 User’s Manual...
Chapter 4: PROGRAM MODE 4.11 cooking instruction data Press the “COOKING TIME” icon on the The “Cooking Time” screen is displayed. menu selection screen. To create the first data, press the [NEW] button. To change existing data, press a desired field To call up desired data, press the Input field for selection and then the [DETAIL] button.
Page 127
Chapter 4: PROGRAM MODE The confirmation screen is displayed. Press the Return button to finish the editing. To confirm changes, press [SAVE]. To undo changes, press [CANCEL]. The edited data has been registered. Press the Input field at the bottom right of the screen to display the keypad.
Chapter 4: PROGRAM MODE 4.12 extra message data Press the “EXTRA MSG.” icon on the menu The “Extra Message” screen is displayed. selection screen. To create the first data, press the [NEW] button. To change existing data, press a desired field To call up a desired data number, press the for selection and then the [DETAIL] button.
Page 129
Chapter 4: PROGRAM MODE Press the Return button to finish the editing. The confirmation screen is displayed. To confirm changes, press [SAVE]. To undo changes, press [CANCEL]. The edited data has been registered. 4-45 UNI-9 User’s Manual...
Chapter 4: PROGRAM MODE 4.13 coupon message data Press the “COUPON MSG.” icon on the The “Coupon Message” screen is displayed. menu selection screen. To create the first data, press the [NEW] button. To change existing data, press a desired field To call up desired data, press the Input field for selection and then the [DETAIL] button.
Page 131
Chapter 4: PROGRAM MODE Press the Return button to finish the editing. The confirmation screen is displayed. To confirm changes, press [SAVE]. To undo changes, press [CANCEL]. The edited data has been registered. 4-47 UNI-9 User’s Manual...
Chapter 4: PROGRAM MODE 4.14 pop message data Press the “POP MSG.” icon on the menu The “POP Message” screen is displayed. selection screen. To create the first data, press the [NEW] button. To change existing data, press a desired field To call up desired data, press the Input field for selection and then the [DETAIL] button.
Page 133
Chapter 4: PROGRAM MODE Press the Return button to finish the editing. The confirmation screen is displayed. To confirm changes, press [SAVE]. To undo changes, press [CANCEL]. The edited data has been registered. 4-49 UNI-9 User’s Manual...
Chapter 4: PROGRAM MODE 4.15 scheme table data Press the “SCHEME TABLE” icon on the The “Scheme Table” screen is displayed. menu selection screen. To create the first data, press the [NEW] button. To change existing data, press a desired field To call up desired data, press the Input field for selection and then the [DETAIL] button.
Page 135
Chapter 4: PROGRAM MODE The “Scheme Table / Edit screen” is Press the Return button to finish the editing. displayed. Edit text according to the procedure described in Appendix “Text Editing”. The confirmation screen is displayed. The edited data has been registered. To confirm changes, press [SAVE].
Page 136
Chapter 4: PROGRAM MODE ITEM DESCRIPTIONS Press this field to select whether or not to use this lot number. RETAIN LOT No. 0: No 1: Yes PASSPORT FORMAT No. Enter a numerical value and press this field. ICON No. Enter a numerical value and press this field. LIFE OFFSET Enter a numerical value and press this field.
Page 137
Chapter 4: PROGRAM MODE The edited data has been registered. Upon completion of the table data registration, press the Return button. 4-53 UNI-9 User’s Manual...
Chapter 4: PROGRAM MODE 4.16 GEN table data Press the “GEN TABLE” icon on the menu The “GEN Table” screen is displayed. selection screen. Press a desired field for selection. To change the text, press the [EDIT] button. Enter a numerical value, press the applicable field, and press the [SET] key.
Page 139
Chapter 4: PROGRAM MODE The confirmation screen is displayed. The edited data has been registered. To confirm changes, press [SAVE]. To undo changes, press [CANCEL]. 4-55 UNI-9 User’s Manual...
Chapter 4: PROGRAM MODE 4.17 Lookup Table data Press the “LOOKUP TABLE” icon on the The “Lookup Table” screen is displayed. menu selection screen. To create the first table, press the [NEW] button. To change existing data, press a desired field To call up desired data, press the Input field for selection and then the [DETAIL] button.
Page 141
Chapter 4: PROGRAM MODE The confirmation screen is displayed. Press the Return button to finish the editing. To confirm changes, press [SAVE]. To undo changes, press [CANCEL]. To create the first data, press the [NEW] The edited text has been registered. button.
Page 142
Chapter 4: PROGRAM MODE The Lookup Data / Text Edit screen is Press the Return button to finish the editing. displayed. Edit text according to the procedure described in Appendix “Text Editing”. The confirmation screen is displayed. The edited data has been registered. To confirm changes, press [SAVE].
Chapter 4: PROGRAM MODE 4.18 mince traceability data Press the "MINCE TRACE.” icon on the The “Mince Traceability” screen is displayed. menu selection screen. Press a desired field for selection. The keypad is displayed. Press the Return button to complete the procedure.
Chapter 4: PROGRAM MODE 4.19 FixeD price symbols Press the "FIX PRICE SYMBOL” icon on the The “Fix Price Symbol” screen is displayed. menu selection screen. Press the Input field at the bottom right of the Enter a desired table number and press the screen to display the keypad.
Page 145
Chapter 4: PROGRAM MODE The edited text has been registered. The confirmation screen is displayed. To confirm changes, press [SAVE]. To undo changes, press [CANCEL]. 4-61 UNI-9 User’s Manual...
Chapter 4: PROGRAM MODE 4.20 free message data Press the "FREE MSG.” icon on the menu The “Free Message” screen is displayed. selection screen. To create the first message, press the [NEW] button. To change existing data, press a desired field To call up desired data, press the Input field for selection and then the [DETAIL] button.
Page 147
Chapter 4: PROGRAM MODE Press the Return button to finish the editing. The confirmation screen is displayed. To confirm changes, press [SAVE]. To undo changes, press [CANCEL]. The edited data has been registered. 4-63 UNI-9 User’s Manual...
Chapter 4: PROGRAM MODE 4.21 check label data Press the "CHECK LABEL” icon on the The “Check Label” screen is displayed. menu selection screen. Press a desired field. Enter the start number and the end number Press the [STRAT] button to print a label. via the keypad, and press the [SET] key.
Chapter 4: PROGRAM MODE 4.22 STAMP PRICE data Press the "STAMP PRICE” icon on the menu The “Stamp Price” screen is displayed. selection screen. Press a desired field for selection. Enter the stamp price and the reference price via the keypad, and press the [SET] key.
Chapter 4: PROGRAM MODE 4.23 nutrition text data Press the "NUTRITION TEXT” icon on the The “Nutrition Text” screen is displayed. menu selection screen. To create the first text, press the [NEW] button. To change existing data, press a desired field To call up desired data, press the Input field for selection and then the [DETAIL] button.
Page 151
Chapter 4: PROGRAM MODE The “Nutrition Text / Edit” screen is Press the Return button to finish the editing. displayed. Edit text according to the procedure described in Appendix “Text Editing”. The confirmation screen is displayed. The edited data has been registered. To confirm changes, press [SAVE].
Chapter 5: SETUP MODE SETUP MODE 5.1 setup mode entry / Exit Ensure that the initial screen is displayed. The “Menu” screen is displayed. Then, press the Return button on the screen Then, press the [SETUP] button. to display the “Menu” screen. Note: The contents of the initial screen may differ depending on the settings on your machine.
Chapter 5: SETUP MODE MACHINE NUMBER / NETWORK NUMBER Press the “MACHINE No.” icon on the menu The “Machine No. (Basic)” screen is selection screen. displayed. Press a desired field for selection. Enter a numerical value via the keypad and press the [SET] key.
Page 154
Chapter 5: SETUP MODE The confirmation screen is displayed. Press [EXEC] to continue, or [STOP] to go back. UNI-9 User’s Manual...
Chapter 5: SETUP MODE SALES MODE Press the “SALES MODE” icon on the menu The “Sales Mode” screen is displayed. selection screen. Then, select a desired sales mode by pressing the corresponding button. EXAMPLE “With Operator” Press the Return button to complete the procedure.
Chapter 5: SETUP MODE PASSWORD Press the “PASSWORD” icon on the menu The “Password (Operate)” screen is selection screen. displayed. Press the “TOTAL” tab to display the Press the “PROGRAM” tab to display the “Password (Total)” screen. “Password (Program)" screen. ...
Page 157
Chapter 5: SETUP MODE Press the “SETUP” tab to display the “Password (Setup)” screen. To turn pages, press [ ] or [ Press the “ADJUST” tab to display the “Password (Adjust)" screen. UNI-9 User’s Manual...
Page 158
Chapter 5: SETUP MODE Press the “PASSWORD” field to display the Select a desired mode by pressing the keypad. corresponding tab, and press any selection Enter a 6-digit password and press [SET] key buttons to set whether or not to prompt the on the keypad.
Chapter 5: SETUP MODE KEY LOCK Press the “KEY LOCK” icon on the menu The “Key Lock (Display Key)” screen is selection screen. displayed. Press the “FUNCTION KEY” tab to display the “Key Lock (Function Key)” screen. To turn pages, press [ ] or [ ...
Page 161
Chapter 5: SETUP MODE Press the “PASSWORD” field to display the Select a desired key category by pressing the keypad. corresponding tab, and press any selection Then, enter a 6-digit password and press the buttons to lock or unlock lock the key. [SET] key on the keypad.
Chapter 5: SETUP MODE DATA STORAGE Press the “DATA STORAGE” icon on the The “Data Staorage (Total Add)” screen is menu selection screen. displayed. To turn pages, press [ ] or [ Press any selection buttons to set whether or not to apply the total addition function for each menu.
Chapter 5: SETUP MODE PRESET REPORT Press the “PRESET REPORT” icon on the The “Preset Report (Daily)” screen is menu selection screen. displayed. To turn pages, press [ ] or [ Press the “WEEKLY” tab to display the “Preset Report (Weekly)”...
Page 164
Chapter 5: SETUP MODE Press the “CUMULATIVE” tab to display the “Preset Report (Cumulative)” screen. To turn pages, press [ ] or [ Select a desired report type by pressing the Press the Return button to complete the corresponding tab, and press any selection procedure.
Chapter 5: SETUP MODE PLU OVERWRITE Press the “PLU OVERWRITE” icon on the The “PLU Overwrite” screen is displayed. menu selection screen. To turn pages, press [ ] or [ Note: Display items may vary depending on the country setting.
Page 166
Chapter 5: SETUP MODE Press the Return button to complete the procedure. UNI-9 User’s Manual 5-15...
Chapter 5: SETUP MODE PLU INITIAL DATA Press the “PLU INITIAL DATA” icon on the The “PLU Initial Data (Sale 1)” screen is menu selection screen. displayed. Press [<] or [>] to select a desired sales mode. 0: Weight (for selling weighing products) SALES MODE 1: Fix price (for selling fixed price products) 2: Weight fix price (for selling weighing fixed price products)
Page 168
Chapter 5: SETUP MODE Press [<] or [>] to select a desired markdown mode. 0: Normal price 1: Special price 2: Amount discount for total price MARKDOWN MODE 3: Percent discount for total price 4: Special unit price 5: Amount discount for unit price 6: Percent discount for unit price M/D AMOUNT Enter a markdown amount or percentage and press this field.
Page 169
Chapter 5: SETUP MODE DESCRIPTIONS ITEM Press [<] or [>] to select whether or not to use the point flag. POINT FLAG 0: OFF 1: ON Press [<] or [>] to select a desired point type. POINT TYPE 0: Weight 1: Fixed weight POINTS Enter a desired number and press this field.
Page 170
Chapter 5: SETUP MODE The “Extra Message” screen is displayed. The selected message has been registered. Press a desired field for selection. Press the “IMAGE” tab to display the “PLU Press a desired field for selection. Initial Data (Image)” screen. UNI-9 User’s Manual 5-19...
Page 171
Chapter 5: SETUP MODE The “Image” screen is displayed. The selected image has been registered. Press a desired image for selection. Press [NO PRINT] or [PRINT] in the “Safe Handling Image” field to select whether or not to print the image. Press the Display Image field.
Page 172
Chapter 5: SETUP MODE Press the “PRINT” tab to display the “PLU Initial Data (Print)” screen. ITEM DESCRIPTIONS 1st LABEL FORMAT Enter a desired format number and press this field. No. (M) 2nd LABEL Enter a desired format number and press this field. FORMAT No.
Page 173
Chapter 5: SETUP MODE Press the “DATE” tab to display the “PLU Initial Data (Date)” screen. ITEM DESCRIPTIONS Press [YES] or [NO] in this field to select whether or not to print the packed PACK DATE PRINT date. Press [<] or [>] to select a desired pack time printing method. 0: No print PACK TIME PRINT 1: Designated time...
Page 174
Chapter 5: SETUP MODE Press the “CODE” tab to display the “PLU Initial Data (Code)” screen. DESCRIPTIONS ITEM ITEM CODE Enter an item code and press this field. REG CODE Enter the register code and press this field. This field is available only when “1: PLU File” is selected in “POS POS FLAG REFERENCE”.
Page 175
Chapter 5: SETUP MODE Press this field to display the “Barcode Format” screen, and press a desired barcode format for selection. POS FORMAT (WGT) Press [YES] or [NO] in this field to select whether or not to enable a TRACE ENABLE traceability function.
Page 176
Chapter 5: SETUP MODE Press the “LINK” tab to display the “PLU Press the Return button to complete the Initial Data (Link)” screen. procedure. UNI-9 User’s Manual 5-25...
Chapter 5: SETUP MODE 5.10 PLU UPDATE Press the “PLU UPDATE” icon on the menu The “PLU Update” screen is displayed. selection screen. To turn pages, press [] or [ ]. Note: Display items may vary depending on the country setting.
Page 178
Chapter 5: SETUP MODE Enter the start and end numbers and press these fileds respectively to specify the target PLUs. UNI-9 User’s Manual 5-27...
Page 179
Chapter 5: SETUP MODE Press desired items for selection. Note 1: To clear the selection, press the selected field again. Note 2: To clear all selections at one time, press the [BATCH DELETE] button. Press the [EXEC] button to update the The confirmation screen is displayed.
Chapter 5: SETUP MODE 5.11 RECEIPT SETTING Press the “RECEIPT SETTING” icon on the The “Receipt Setting (Title)” screen is menu selection screen. displayed. To edit the header and footer titles, press the corresponding field. The text edit screen is displayed. To finish the editing, press the Return button Edit the text according to the procedure on the screen.
Page 181
Chapter 5: SETUP MODE The “Header Image” screen is displayed. Press a desired image for selection. The selected logo image has been registered. UNI-9 User’s Manual 5-30...
Chapter 5: SETUP MODE 5.12 tax registration Press the “TAX” icon on the menu selection screen. The “Tax” screen is displayed. ITEM DESCRIPTIONS TAX TYPE Press a desired tax type for selection. Exclusive tax Inclusive tax Tax exemption TAX RATE Enter a numerical value and press the applicable field.
Chapter 6: ADJUSTMENT MODE ADJUSTMENT MODE ADJUSTMENT MODE ENTRY / EXIT Ensure that the initial screen is displayed. The “Menu” screen is displayed. Then, press the [ADJUST] button. Then, press the Return button on the screen to display the “Menu” screen. Note: The content of the initial screen may differ depending on the settings on your machine.
Chapter 6: ADJUSTMENT MODE DATE / TIME Press the “DATE TIME” icon on the menu The “Date / Time” screen is displayed. selection screen. To change the date, press the “DATE” field and enter a new date data. Then, press the [SET] key. EXAMPLE 22 June, 2007 Enter...
Page 185
Chapter 6: ADJUSTMENT MODE Enter To register new date and time, press the The confirmation screen is displayed. [SET] button. Press [EXEC] to continue, or [STOP] to go back. UNI-9 User’s Manual...
Chapter 6: ADJUSTMENT MODE TOUCH SCREEN Press the “TOUCH SCREEN” icon on the The “Touch Screen” screen is displayed. menu selection screen. Press [+] on the button at the upper left of the Press [+] on the button at the lower right of screen with a round-pointed device.
Chapter 6: ADJUSTMENT MODE DISPLAY CHECK Press the “DISPLAY CHECK” icon on the The “Display Check (Vertical)” screen is menu selection screen. displayed. Press [-] or [+] to adjust the vertical brightness for operator and customer displays. The “Display Check (Horizontal)” screen is Press the [HORIZONTAL] button to change displayed.
Chapter 6: ADJUSTMENT MODE SOUND Press the “DISPLAY CHECK” icon on the The “Sound” screen is displayed. menu selection screen. To set sound levels, press “ON” in the “Sound” field and press [ < ] or [ > ]. UNI-9 User’s Manual...
Page 189
Appendix: TEXT EDITING TEXT EDITING EDIT SCREENS Upper-case mode Used to finalize the editing Displays the called number Displays the number of Press this field to select a input characters desired font size Press this field to select a Displays the number of remaining desired font style characters Lower-case mode...
Appendix: TEXT EDITING EDIT KEYS Used to switch between Used to specify a normal lower-case and upper-case character style. character modes. Used to specify a bold character Used to begin a new line. font style. Used to delete a line text at the Used to specify a reverse place where the cursor is placed.
Page 192
Appendix: TEXT EDITING Used to display the following key screen. UNI-9 User’s Manual...
Appendix: TEXT EDITING INPUT EXAMPLES A.3.1 TEXT EDITING Enter desired characters using alpha-numeric keys. Upper-case characters Lower-case characters To begin a new line, press the [New Line] key. Enter desired characters. The confirmation screen is displayed. To register the editing, press the Return To confirm changes, press [SAVE].
Appendix: TEXT EDITING A.3.2 FONT STYLE SELECTION Press the following keys to select a desired font style. Note: The selected font style is displayed in the “STYLE” display field. Enter desired characters using alpha-numeric keys. UNI-9 User’s Manual...
Page 195
Appendix: TEXT EDITING The confirmation screen is displayed. Press the Return key to register the editing. To confirm changes, press [SAVE]. To undo changes, press [CANCEL]. UNI-9 User’s Manual...
Appendix: TEXT EDITING A.3.3 LINE DATA DELETION Press the [Line Delete] key to delete the line The line data has been deleted. data. Press the Return button to register the deletion. The confirmation screen is displayed. To confirm changes, press [SAVE]. To undo changes, press [CANCEL UNI-9 User’s Manual...
Appendix: TEXT EDITING A.3.4 DATA ERASE Press the [ERASE] button to delete the full The confirmation screen is displayed. text currently being called. Press [EXEC] to continue, or [STOP] to go back. The full text has been erased. UNI-9 User’s Manual...
Appendix: TEXT EDITING A.3.5 DATA COPY To call up a desired string of characters, Then, enter a numerical value and press the press the INPUT field at the bottom right of [SET] key on the keypad. the screen to display the keypad. Enter Press the [COPY] key while the number is The confirmation screen is displayed.
Page 200
Specifications subject to change without notice. Rice Lake Weighing Systems is an ISO 9001 registered company. 230 W. Coleman St. • Rice Lake, WI 54868 • USA U.S. 800-472-6703 • Canada/Mexico 800-321-6703 • International 715-234-9171 • Europe +31 (0)26 472 1319 www.ricelake.com/retail...