X-lander X-RUN User Manual page 10

G UA R D R A I L A DA P T E R S D I S A S S E M B LY
14
To disassemble the guardrail adapters, remove them from the mounting slots by pulling
the red lock lever.
15 G UA R D R A I L A S S E M B LY
To assemble the guardrail, push the ends of the guardrail into the mounting holes until
the locks engage.
16 G UA R D R A I L D I S A S S E M B LY
To disassemble the guardrail, press the guardrail lock buttons and slide guardrail ends out
of the mounting holes (a). The guardrail can be turned by unfastening it from one side only.
Attention: Fold or remove the guardrail before folding the trolley. To fold the guardrail, press
buttons located on the guardrail sides (b) and set the guardrail in the folding position (c).
17 F O OT R E S T A D J U S T M E N T
Press the buttons on both sides of footrest and adjust it to the required position.
18
H A N D B R A K E
The hand brake is used for speed reduction (braking) of the stroller e.g. when riding
down a steep slope. During faster stroller rides e.g. while jogging, tighten the wristband
and hold one hand on the brake lever the whole time.
19 M O U N T I N G A N D U N M O U N T I N G T H E S E AT U N I T ( U P H O L S T E R Y)
Unscrew the screws holding he sides of the seat unit to the frame using a cross screw­
driver (a). Unfasten the snaps on the footrest (b) and unfasten the belt buckle from
underneath the seat unit (c). Unfasten the seat unit hooks on the back legs together with
the regulation belts on both sides of the frame (d). Unmount the seat unit from the side
hooks of the frame (e). To mount the seat unit, perform the above steps in reverse order.
20
C A R R YC OT M O U N T I N G
To assembly body pram you should use special adapters. Remove the seat unit. Remove
the plugs from fastening sockets by drawing red lock's lever away and put adapters
inside them, putting them till moment of entire blockage. Put carrycot on adapters by
putting adapters tips inside assembling openings and tightening locks.
Check before use if carrycot is assembled correctly.
21
C A R R YC OT U N M O U N T I N G
To disassembly carrycot unblock fastening locks by pressing button, which are shown
on photo and remove carrycot by lifting up from adapters. Disassembly adapters by
drawing them out from fastening sockets having first drawn back the red lock lever.
Attention:
22
M O U N T I N G T H E C A R S E AT
To mount the car seat use special adapters. Unmount the seat unit. Remove the plugs from
the mounting points using the red lever and put in the adapters until locked. Mount the car
seat on the adapters by pressing the adapter tips into the mount­points on the car seat.
Press the car seat firmly until the safety locks have engaged. Attention: Before using the
stroller check carefully if the car seat unit has been properly fitted to the chassis.
23 R E M OV I N G T H E C A R S E AT
To remove the car seat release the safety locks pressing the buttons on both sides of the
stroller as show in the picture. Pull up the car seat to detach it from the chassis. Disas­
semble the adapters by removing them from the mount­points, having first drawn back
the red lock lever.
24 P R OT E C T I N G C A P S
Where the adapters for gondola fastening are not used, the assembly sockets should be
8
covered with protecting caps. The caps should be inserted into the assembly sockets as
shown in the picture.
It's impossible to fold the stroller with assembled adapters.
Attention:
The stroller will not fold with the adapters fitted.
Attention: