Ce Declaration Of Conformity; Warning For The Installer - FAAC 596MPS Manual

ENGLISH
Manufacturer: FAAC S.p.A.
Address: Via Benini, 1 - 40069 Zola Predosa BOLOGNA - ITALY
Declares that: Electronic appliances 596MPS and 610MPS
• conform to the essential safety requirements of the following directives:
73/23/EEC and subsequent amendment 93/68/EEC.
89/336/EEC and subsequent amendment 92/31/CEE and 93/68/EEC
Additional information:
These products underwent tests in a typical, uniform configuration (all products manufactured by FAAC
S.p.A.).
Bologna 01 January 1999
1) CAUTION! It is important for personal safety to follow all the instructions
carefully. Incorrect installation or misuse of the product may cause
people serious harm.
2) Read the instructions carefully before starting to install the product.
3) Packaging material (plastic, polystyrene, etc.) must not be left within reach
of children as it is a potential source of danger.
4) Keep the instructions in a safe place for future reference.
5) This product was designed and manufactured strictly for the use indicated
in this documentation. Any other not expressly indicated use may damage
the product and/or be a source of danger.
6) FAAC accepts no responsibility due to improper use of the automation or
use other than that intended.
7) Do not install the appliance in an area subject to explosion hazard: inflam-
mable gasses or fumes are a serious safety hazard.
8) Mechanical construction elements must meet the provisions of UNI8612,
CEN pr EN 12604 and CEN pr EN 12605 Standards.
To obtain an adequate level of safety in non EU countries, the above
mentioned Standards must be observed in addition to national standards.
9) FAAC will not accept responsibility if the principles of Good Workmanship
are disregarded in constructing the closing elements to be motorised, and
if any deformation occurs during use of the said elements.
10) Installation must meet the following Standards: UNI8612, CEN pr EN 12453
and CEN pr EN 12635.
The safety class for the automation must be C+D.
11) Before carrying out any work on the system, switch off the power supply.
12) The mains power supply of the automation must be fitted with a all-pole
switch with contact opening distance of 3mm or greater. Use of a 6A
thermal breaker with all-pole circuit break is recommended.
13) Make sure there is a differential switch with 0.03A threshold upstream of the
system.
14) Check that the earthing system is correctly made and connect the closure
metal parts to it. Also connect the Yellow/Green wire of the automation to
the earthing system.

CE DECLARATION OF CONFORMITY

The Managing Director

WARNING FOR THE INSTALLER

GENERAL SAFETY OBLIGATIONS
A. Bassi
15) The automation includes an intrinsic anti-crushing device consisting of a
torque control which, however, must be installed together with other
safety devices.
16) The safety devices [e.g.: photocells, sensitive edges, etc...] protect any
dangerous areas against Movement mechanical risks, such as, crushing,
dragging, or shearing.
17) Use of at least one indicator-light is essential for each system (e.g.: FAAC
LAMP MINILAMP, etc.) as well as a sign adequately fixed to the frame
structure, in addition to the devices mentioned at point "16".
18) FAAC accepts no responsibility regarding safety and correct operation
of the automation, should components made by manufacturers other
than FAAC be used in the system.
19) Use only FAAC original spare parts for maintenance.
20) Do not make any alterations to the components of the automation.
21) The installer must supply full information regarding manual operation of
the system in case of an emergency and hand to the user of the system the
"User's Guide" included with the product.
22) Do not allow children or other persons to stand near the product while in
operation.
23) Keep remote controls or any other pulse generator well away from chil-
dren, to prevent the automation from being activated accidentally.
24) The user must refrain from attempting to repair or adjust the system person-
ally and should contact qualified personnel only.
25) Anything not expressly provided for in these instructions is not
permitted.
5
ENGLISH