Table of Contents
Advertisement
Quick Links
Operation
SaniForce™
SaniForce™
SaniForce™
Pail
Pail
Pail Unloader
Unloader System
Unloader
For use
use with
with food
food grade
grade bulk
For
For
use
with
food
grade
For
For professional
For
professional use
professional
use only.
use
only.
only.
Important
Important Safety
Important
Safety Instructions
Safety
Read all warnings and instructions in this manual and in manuals
identified in the Related Manuals table on page 2. Save
instructions.
instructions.
instructions.
Maximum Working Air Pressure: 100
psi (0.7 MPa, 7 bar)
Maximum Working Fluid Pressure: 650
psi (4.5 MPa, 45 bar)
System
System
bulk supply
supply of of of medium
medium to to to high
bulk
supply
medium
Instructions
Instructions
PROVEN QUALITY. LEADING TECHNOLOGY.
high viscosity
viscosity product.
product.
high
viscosity
product.
Save all all all
Save
3A5400B
EN
Advertisement
Table of Contents
Related Manuals for Graco SaniForce SPU.A01AAA1AA0C21
Summary of Contents for Graco SaniForce SPU.A01AAA1AA0C21
- Page 1 Operation SaniForce™ SaniForce™ SaniForce™ 3A5400B Pail Pail Pail Unloader Unloader Unloader System System System For use use with with food food grade grade bulk bulk supply supply of of of medium medium to to to high high viscosity viscosity product. product.
-
Page 2: Table Of Contents
Locate the Pump System......6 Grounding ........... 7 Dimensions ............12 Fluid Outlet Line........... 7 Technical Data ........... 13 Operation ............8 Graco Standard Warranty........14 Pressure Relief Procedure......8 Flush the Pump Before First Use ....8 Models Models Models... -
Page 3: Warnings
Warnings Warnings Warnings Warnings The following warnings are for the setup, use, grounding, maintenance, and repair of this equipment. The exclamation point symbol alerts you to a general warning and the hazard symbols refer to procedure-specific risks. When these symbols appear in the body of this manual or on warning labels, refer back to these Warnings. - Page 4 Warnings WARNING MOVING MOVING MOVING PARTS PARTS PARTS HAZARD HAZARD HAZARD Moving parts can pinch or amputate fingers and other body parts. • Keep clear of moving parts. • Do not operate equipment with protective guards or covers removed. • Pressurized equipment can start without warning. Before checking, moving, or servicing equipment, follow the Pressure Pressure Pressure Relief...
-
Page 5: Configuration Matrix
Configuration Matrix Configuration Matrix Matrix Configuration Configuration Matrix Check the identification plate (ID) for the following matrix to define the components of your Configuration Number of your pump. Use the system. SPU A01AAA1AA0C21 A01AAA1AA0C21 A01AAA1AA0C21 Sample Sample Sample Configuration Configuration Configuration Number: Number: Number:... -
Page 6: Installation
Installation Installation Installation Installation General Information Information General General Information The Typical Installation shown is only a guide for selecting and installing system components. Reference letters in the text, for example (A), refer to the callouts in the figures. The Pail Unloader System consists of parts which are stationary and parts attached to the air cylinder piston rod. -
Page 7: Grounding
Installation Integrated Integrated Integrated Air Air Control Control Control Second bleed-type bleed-type air air valve valve (W): (W): isolates air line • Second Second bleed-type valve (W): accessories and supply system for servicing. Locate upstream from all other air line accessories. The integrated air control includes: Air relief relief valve... -
Page 8: Operation
Operation Operation Operation Operation 2. Place a full pail on the base and center it under the Platen (D). 3. Adjust the pail to be sure it is aligned with the platen, and open the platen bleed port (J). NOTE: NOTE: NOTE: If the platen is not aligned properly for Pressure... -
Page 9: Change Pail
Operation Change Pail Pail Change Change Pail 3. Remove the empty pail. 4. Inspect platen and, if necessary, remove 1. Turn off pump air supply by pushing the air motor any remaining material or material slider valve (BH) to the off position. build-up. -
Page 10: Maintenance
Maintenance Maintenance Maintenance Maintenance Lubrication Lubrication Lubrication • Flush at the lowest pressure possible. Check connectors for leaks and tighten as necessary. The pump is lubricated at the factory. It is designed • Flush with a fluid that is compatible with the fluid to require no further lubrication for the life of the being dispensed and the equipment wetted parts. -
Page 11: Cleaning The Platen
Maintenance Cleaning the the Platen Platen Cleaning Cleaning Platen 1. Remove the pail. See Change Pail, page 9 2. Lower the ram so that the platen is resting flat against the baseplate. 3. Disconnect the blowoff air hose at the blowoff port (K). -
Page 12: Dimensions
Dimensions Dimensions Dimensions Dimensions In. (mm) In. (mm) In. (mm) In. (mm) In. (mm) In. (mm) In. (mm) 62.82 (1596) 42.34 (1075) 6.0 (152) 24.82 (630) 12.0 (305) 22.0 (559) 10.0 (254) 3A5400B... -
Page 13: Technical Data
Technical Data Technical Data Data Technical Technical Data Sanitary Sanitary Pail Sanitary Pail Unloader Pail Unloader Unloader Metric Metric Metric Maximum fluid working pressure 650 psi 4.5 MPa, 44.8 bar Maximum air inlet pressure 100 psi 0.7 MPa, 6.9 bar Air consumption See pump manual Maximum recommended pump... -
Page 14: Graco Standard Warranty
Graco to be defective. This warranty applies only when the equipment is installed, operated and maintained in accordance with Graco’s written recommendations. This warranty does not cover, and Graco shall not be liable for general wear and tear, or any malfunction, damage or wear caused by faulty installation, misapplication, abrasion, corrosion, inadequate or improper maintenance, negligence, accident, tampering, or substitution of non-Graco component parts.