Download
Share
Print this page
pottery barn kids KENDALL Manual
  1. Manuals
  2. Brands
  3. pottery barn kids Manuals
  4. Indoor Furnishing
  5. KENDALL
  6. Manual

pottery barn kids KENDALL Manual

Storage desk
Hide thumbs Also See for KENDALL:
1
2
3
4
5
6
7
8
9

Advertisement

Quick Links

Download this manual See also: Manual
pottery barn kids
KENDALL STORAGE DESK
www.potterybarnkids.com
Date: 2015-May-29
Page 1 of 8
Rev: 2015-July-29

Advertisement

loading
Need help?

Need help?

Do you have a question about the KENDALL and is the answer not in the manual?

Questions and answers

Related Manuals for pottery barn kids KENDALL

Summary of Contents for pottery barn kids KENDALL

  • Page 1 KENDALL STORAGE DESK www.potterybarnkids.com Date: 2015-May-29 Page 1 of 8 Rev: 2015-July-29...
  • Page 2 Important Safety Instructions: Please read all instructions carefully before assembling this Desk. • For your safety, assembly by two or more adults is strongly recommended. • Keep these instructions for future use. • Use only vendor-supplied hardware to assemble this item. Using unauthorized hardware could jeopardize the •...
  • Page 3 Assembly Instruction Steps: 1. Remove the drawer from the Desk Top (A) and set aside, as shown below. Open the Drawer to its maximum opening Lift up the left trigger and press down the right trigger on the drawer sides During assembly, the drawer can be removed by releasing the triggers and pulling out the drawer AT THE SAME TIME Left...
  • Page 4 3. Insert 4 Cams (H) into the pre-drilled holes, located on the rear frame of Desktop (A) and Back Rail (C), as seen below. 4. Make sure that the arrow marks on the Cams (H) point toward to the end of the rear frame, as shown below. Note: Prior to inserting the Cam into the countersunk, align the outer arrow on the Cam with the inner arrow at the center of the Cam, as seen below.
  • Page 5 5. Attach the 4 Cam Screws (I) to the Pedestal (B) and Left End Panel (D) by using Phillips Head Screwdriver (Not included), as shown below. Do not over tighten. 6. Attach (B) to (A)&(C) by aligning the Cam Screws (I) to the Cams (H), as seen in illustration below. 7.
  • Page 6 9. Tighten the bolts securely with the supplied Allen Key 4mm (E), as shown below. Do not fully tighten. 10. Attach (D) to (A&C) by aligning the Cam Screws (I) to the Cam (H), as seen in illustration below. 11. Tighten the Cam (H) securely with the supplied Allen Key 6mm (F), as shown below. Do not fully tighten. 12.
  • Page 7 14. Carefully turn the assembled desk upright. 15. Put the drawer back into the desktop. Let both the ball bearing slides be front of the slide. Align the Male runner on the drawer sides to the FEMALE runner on the desk top frame (A) and slowly push the drawer into the desk top frame Pull and push a couple times to make sure it is correctly installed Make sure to check proper assembly by slowly pulling in and out the drawer all the way...
  • Page 8 17. Adjust the levelers located on the bottom of the legs (up or down) to keep the desk level when needed. DOWN Care Instructions: Dust often using a clean, soft, dry, and lint-free cloth. • Blot spills immediately and wipe with a clean, damp cloth. •...
  • Page 9 FURNITURE TIPPING RESTRAINT WARNING: This product is only a deterrent. It is not a substitute for proper adult supervision. Manufacturer assumes no liability for improper installation or excessive loads placed on screws, brackets or straps. Young children may be injured by tipping furniture and the use of a tipping restraint is highly recommended.