Related Manuals for pottery barn kids STAR WARS BED
Summary of Contents for pottery barn kids STAR WARS BED
- Page 1 STAR WARS BED (Part 2 of 2) Please follow strickly this assembling instruction to prevent this bed from damage or misalignment. www.potterybarnkids.com Date: 2054-Jun.-18 Rev: Page 1 of 14...
- Page 2 WARNING:. Follow mattress manufacturer instructions for use. Use proper ventilation foundation with latex mattresses. Failure to follow this instruction can lead to property damage. Important Safety Instructions: • Please read all instructions carefully before assembling. • For your safety, assembly by four or more adults is strongly recommended.
- Page 3 (A) Footboard (x1) (B) Headboard (x1) (CL) Left triangle block(x2) (CR) Right triangle block(x2) (DL) 1 Left side rail(x1) (DR) 1 Right side rail(x1) (EL) 2 Left side rail(x1) (ER) 2 Right side rail(x1) (F) 3 Side rail(x2) (G) Bottom Panel(x1) (H) Leg(x4) (I) Platform panel(x3) (J) Center leg(X3)
- Page 4 ASSEMBLY INSTRUCTIONS 1. Make sure the Footboard (A) is fully assembled followed separated AI. Lay down (A ) on a Styrofoam taken from the carton as seen in the illustration below. Using Platform Panel (I) as an measurement to make sure the Footboard is placed straightly as shown below.
- Page 5 3. Attach 4pcs (H) to 02pcs (F), with the pre-drilled holes aligned, as seen in the illustration below. 4. Attach (F) to (A), with the wooden dowels and pre-drilled holes aligned, as seen in the illustration below. Adjust the levelers on the bottom of the unit (up or down) to level the panel. Date: 2015-Jun.-18 Rev: Page 5 of 14...
- Page 6 Tighten with bolt (attach to (A)) and mending plate (attach to (F)), as seen in the illustration below. *Tip: See Image A (Page 4) for ease of assembly. 6. Repeat step #4 to assemble another side Rail (F), as seen in the illustration below. Date: 2015-Jun.-18 Rev: Page 6 of 14...
- Page 7 7. Repeat step # 5 to assemble another side Rail (F) to (A) & (G), as seen in the illustration below. *Tip: See Image A (Page 4) for ease of assembly. 8. Attach (EL& ER) to (A), as seen in the illustration below. *Tip: See Image A (Page 4) for ease of assembly.
- Page 8 Attach (EL) and (ER) to (F), as seen in the illustration below. Note: Tighten the mending plate to the pre-drilled holes first. Check aligment and tighten the rest screws. 10. Thread (U) to (DL&DR), as seen in the illustration below. Date: 2015-Jun.-18 Rev: Page 8 of 14...
- Page 9 Note: - Prior to inserting the Cam into the countersunk, align the outer arrow on the Cam with the inner arrow at the center of the Cam, as seen below. - The cam may become disassembled during shipping. If you find it disassembled, please re-assemble, as shown in the illustration below.
- Page 10 12. Insert (U) to (A), as seen in the illustration below. 13. Insert (T) to (CL&CR), attach(DL&DR) to (A), tighten (T) with Allen key (S) as seen in the illustration below. Date: 2015-Jun.-18 Rev: Page 10 of 14...
- Page 11 14. Repeat step # 5 to secure (DL&DR ) to (A) and (EL & ER), as seen in the illustration below. 15. Insert (U) to (B) , as seen in the illustration below. Date: 2015-Jun.-18 Rev: Page 11 of 14...
- Page 12 16. Insert (T) to (CL&CR), attach(B) to (CL&CR), tighten (T) with Allen key (S) as seen in the illustration below. 17. Secure all side rails to Headboard (B), as seen in the illustration below. *Tip: See Image A (Page 4) for ease of assembly. Date: 2015-Jun.-18 Rev: Page 12 of 14...
- Page 13 18. Thread 03pcs (J) to 03pcs (I), as seen in the illustration below. 19. Place (I) in between of slat support on side rails, adjust the levelers on the bottom of the support legs (J) up or down) to level the panel, as seen in the illustration below. Date: 2015-Jun.-18 Rev: Page 13 of 14...
- Page 14 20. Secure (I) with screw (X). 21. Remove the Styrofoam under the footboard, as seen in the illustration below. 22. Assembly is now complete. Care Instructions: • Dust often using a clean, soft, dry, and lint-free cloth. • Blot spills immediately and wipe with a clean, damp cloth. •...