Advertisement
4.
Connect Power
1. Plug the AC power cord into the socket on the rear of
the switch.
2. Connect the other end of the power cord to an AC
power source. Verify that the external AC power
requirements for the switch can be met as listed below:
SC50010: 100-240 VAC, 50/60 Hz, 18.4 A
i
Note: For International use, you may need
to change the AC line cord. You must use a
line cord set that has been approved for the
socket type in your country.
5.
Verify Switch Operation
Verify basic switch operation by checking the system LEDs.
When operating normally, the System, PWRA and/or
PWRB LEDs should be on and green depending on the
number of power supplies used in the switch.
6.
Connect to the Web User Interface
1. Connect a PC to the switch through one of the RJ-45
ports.
2. The switch has a default management IP address of
192.168.2.1 and a subnet mask of 255.255.255.0. You
must set your PC IP address to be on the same subnet
as the switch (that is, the PC and switch addresses
must both start with 192.168.2.x).
3. Log in to the web interface or CLI using the default
settings: username "admin" and password "admin".
www.signamax.com
7.
Connect
Network Cables
1. For RJ-45 ports, connect 100-ohm Category 5, 5e or
better twisted-pair cable.
2. For the SFP/SFP+ slots, first install SFP/SFP+
transceivers and then connect fiber optic cabling to the
transceiver ports. All Signamax 1G and 10G SFPs are
supported.
3. As connections are made, check the port status LEDs
to be sure the links are valid. Press the Mode/Reset
button less than 2 seconds to change from Ethernet to
PoE status. RJ45 Ports:
•
On/Blinking Green — Port has a valid 1G link.
•
On/Blinking Amber — Port has a valid 10/100Mb
link.
SFP/SFP+ Ports:
•
On/Blinking Blue — Port has a valid 10G link.
•
On/Blinking Green — Port has a valid 1G link.
Blinking indicates network activity.
8.
Connect to the Console Port
1. Connect a PC to the switch console port using the
included console cable.
2. Configure the PC's serial port: 115200 bps, 8
characters, no parity, one stop bit, 8 data bits, and no
flow control.
3. Log in to the CLI using default settings: Username
"admin" and no password.
9.
Mode/Reset Button
Press
Switch Action
Time
<2
Change LED Mode
2-7
Reboot the switch
Reset the switch to factory
> 7
default and reboot
Hardware Specifications
Switch Chassis
Size
17.4 x x17.1 x 1.73in (44.2 x 44 x
(W x H x D)
4.4cm)
Weight
1 Power Supply: 12.68lb (5.3kg)
2 Power Supplies: 13.89lb (6.3kg)
Temperature
Operating: 32 to 113°F (0 to 45°C)
Storage: -4 to 158°F (-20 to 70°C)
Humidity
10 to 95% (non-condensing)
Power Specification
AC Input
100 - 240 V AC, 50/60 Hz
Power
Dual Redundant
Max Power
1840W
Consumption
Regulatory Compliances
Emissions
CE Mark
•
EN 55022, Class A
FCC Part 15 Subpart B Class A
Immunity
IEC 61000-3-3,IEC61000-4-2/3/4/5/6/8
-
2 -
Quick Start Guide
System LED
ON Green
Blinking Green
Blinking Green
Advertisement
