Jung FMDW360WW Operating Instructions Manual

Jung FMDW360WW Operating Instructions Manual

Enet motion detector

Advertisement

Quick Links

eNet motion detector
eNet motion detector
Art. no.: FMDW360WW
Operating instructions
1
Safety instructions
Electrical devices may only be mounted and connected by electrically skilled persons.
Serious injuries, fire or property damage possible. Please read and follow manual fully.
The radio communication takes place via a non-exclusively available transmission path, and is
therefore not suitable for safety-related applications, such as emergency stop and emergency
call.
These instructions are an integral part of the product, and must remain with the end customer.
2
Battery safety instructions
This device or its accessories are supplied with batteries in the form of alkaline batteries LR03.
DANGER! Batteries can be swallowed. This can lead directly to death by suffocation.
Keep new and used batteries away from children.
Do not use devices if the battery compartment does not close securely and keep away from
children.
If you suspect that a battery has been swallowed or is in any orifice of the body, seek immediate
medical attention.
WARNING! Improper handling of batteries can result in explosion, fire or chemical burn due to
leakage.
Do not heat or throw batteries into fire.
Do not reverse polarity, short-circuit or recharge batteries.
Do not deform or disassemble batteries.
Replace batteries only with an identical or equivalent type.
Remove empty batteries immediately and dispose of in an environmentally friendly manner.
Exchange all batteries at the same time. Only use batteries of the same type and manufacturer.
Do not combine old and new batteries.
3
Intended use
Automatic switching of lighting depending on the heat motion and ambient brightness
Operation only with radio actuators for switching and dimming from the eNet system
Ceiling mounting, surface-mounted, in dry interiors
4
Function
Product characteristics
LED for signalling
Battery-powered device
Brightness threshold settable
Run-on time adjustable
Sensitivity can be set
Can be set with eNet server:
Disabling of manual commissioning
Longer run-on time adjustable
Brightness threshold settable
Power saving level
82598403
J0082598403
1 / 12
25.07.2019

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the FMDW360WW and is the answer not in the manual?

Questions and answers

Subscribe to Our Youtube Channel

Summary of Contents for Jung FMDW360WW

  • Page 1 Art. no.: FMDW360WW Operating instructions Safety instructions Electrical devices may only be mounted and connected by electrically skilled persons. Serious injuries, fire or property damage possible. Please read and follow manual fully. The radio communication takes place via a non-exclusively available transmission path, and is therefore not suitable for safety-related applications, such as emergency stop and emergency call.
  • Page 2: Operation

    eNet motion detector – Transmission behaviour Supplementary functions with eNet Server – Fully encrypted radio transmission (AES-CCM) – Operation with eNet server from version 2.2 – Update of the device software – Reading of error memory Automatic operation The device detects heat motions of people, animals and objects. –...
  • Page 3: Information For Electrically Skilled Persons

    eNet motion detector Information for electrically skilled persons Selecting installation location The sensor is installed on the ceiling and monitors the surface below. The sensor has a detec- tion area of 360° and is more sensitive in the central area than in the peripheral area. The detection of heat sources by a motion detector and thus the extent of the detection field is influenced by the following criteria: Mounting height, sensitivity setting and direction of move- ment.
  • Page 4 eNet motion detector Figure 3: Fasten the base plate ■ Pay attention to correct alignment of the base plate already during mounting. ■ Align the device so that the brightness sensor (3) (Figure 4) is on the side away from the windows.
  • Page 5 eNet motion detector Figure 4: Adjuster Without eNet Server the commissioning should be carried out in the following order. This pre- vents an actuator connected to the sensor from saving an undesired run-on time. Set the run-on time on the sensor. The adjuster Lux (7) must not be set to PC for a run-on –...
  • Page 6 eNet motion detector Figure 5: Insert batteries ■ Pull off decor ring (2). Turn the sensor by approx. 45° in the OPEN direction to disconnect it from the base plate ■ (Figure 2). ■ Insert batteries with correct polarity (Figure 5). The status LED (4) lights up for 1 minute.
  • Page 7 eNet motion detector The connections in the actuators and eNet Server are preserved and must be deleted separately. ■ Turn adjuster Time (6) and Lux (7) (Figure 4) to PC position. ■ Press the Prog. (3) button (Figure 4) for longer than 20 seconds. The status LED (4) flashes after 4 seconds.
  • Page 8: Disposal Of Batteries

    eNet motion detector ■ To exit the walking test: Press Prog button (3) briefly or wait for approx. 5 minutes. Limiting the detection field using the push-on cover The push-on cover can be used to limit the detection field, e.g. in order to mask out interference sources.
  • Page 9: Parameter List

    eNet motion detector Ambient temperature -5 ... +45 °C Degree of protection IP20 Brightness setting approx. 5 ... 2000 lx (and day opera- tion) Sensitivity 25 ... 100% Run-on time approx. 10 s ... 30 min (60 min with eNet Server) Installation height 2.5 m Detection angle 360°...
  • Page 10 eNet motion detector Parameter name Setting options, Basic setting Explanations is ignored and the device works brightness-independent (day operation). This setting does not affect the transmission of brightness values to the eNet Server for use in the eNet SMART HOME app Brightness threshold 5 ...
  • Page 11: Troubleshooting

    eNet motion detector Parameter name Setting options, Basic setting Explanations Transmission behaviour Do not send brightness val- Power-optimised: ues / power-optimised If movements are constantly detected, the device sends a Do not send brightness val- telegram after 3 minutes at the ues / power-optimised latest.
  • Page 12: Warranty

    Limit the detection field using the push-on cover. 12 Conformity Albrecht Jung GmbH & Co. KG hereby declares that the radio system type art. no. FMD- W360WW meets the directive 2014/53/EU. You can find the full article number on the device.

Table of Contents