Subscribe to Our Youtube Channel
Related Manuals for Pulsar Z46G
Summary of Contents for Pulsar Z46G
- Page 1 CAL. Z46G MECHANICAL WATCHES Automatic winding Time and date calendar Power reserve indicator...
- Page 2 DISPLAY AND CROWN/BUTTONS Power reserve hand Minute hand Click button Hour hand CROWN Date Second hand AUTOMATIC 21 Jewels b: First click a: Normal position...
-
Page 3: How To Start The Watch
HOW TO START THE WATCH This is an automatic-winding mechanical watch. To initially start your watch: Swing it from side to side in a horizontal arc for about 30 seconds, to start the second hand moving. * If the watch is worn on the wrist, the mainspring will be wound automatically through normal wrist movement. -
Page 4: Screw Down Crown
SCREW DOWN CROWN [for models with screw down crown] Unlocking the crown 1 Turn Crown counterclockwise until you no longer feel the threads turning. 2 Crown can be pulled out. Locking the crown 1 Push Crown back in to normal position. 2 Turn Crown clockwise while pressing it lightly until tight. -
Page 5: Time / Calendar Setting
TIME / CALENDAR SETTING Setting the time and adjusting the date Hour hand Minute hand 1 Press the click button and set it to the date of a previous day. CROWN 2 Pull out the crown. (The second AUTOMATIC hand does not stop.) 21 Jewels 3 Turn the crown clockwise until you reach the today’s date. -
Page 6: Power Reserve Indicator
POWER RESERVE INDICATOR Power reserve hand The power reserve indicator shows the amount the watch is wound as an amount of time, so you can see how long the watch will run at a glance. The power reserve hand indicates the remaining amount. The time pointed to by the power AUTOMATIC reserve hand is the remaining... -
Page 7: Notes On Operating The Watch
NOTES ON OPERATING THE WATCH TIME/CALENDAR SETTING Do not set the date between 9:00 p.m. and 2:00 a.m. Otherwise, it may not change properly. * If it is necessary to set the date during that time period, first change the time to any time outside it, set the date and then reset the correct time. - Page 8 POWER RESERVE INDICATOR The remaining time shown is only an approximation. The time shown may be different from actual remaining time. This product has an automatic-winding system which comes with a power reserve indicator function. The mainspring will be automatically wound by your natural arm movements while you wear it on your wrist.
-
Page 9: Specifications
SPECIFICATIONS Vibration : 21,600 Oscillations / 1hr Loss/Gain : Within +25 and –15 second (Daily Rate)* Jewels : 21 Jewels * The mechanism of mechanical watches is very precise and delicate. Time accuracy may change depending of which direction the watch faces. Therefore, any actual loss/gain may not fall within the range of time accuracy specified above, and depends on the condition of use, such as the length of time during which the watch is worn on the wrist, temperature, affection of strong magnetism,... - Page 10 If the watch becomes wet, we suggest that you Water resistance (10 bar/15 bar/20 bar)* have it checked by an AUTHORIZED PULSAR If “WATER RESISTANT 10 BAR”, DEALER or SERVICE CENTER. “WATER RESISTANT 15 BAR”...
- Page 11 * Before using the water resistance 5, 10, 15 or 20 bar watch in water, be sure the crown is pushed in completely. Do not operate the crown when the watch is wet or in water. If used in sea water, rinse the watch in fresh water and dry it completely.
-
Page 12: Periodic Check
PERIODIC CHECK CARE OF CASE AND BRACELET To prevent possible rusting It is recommended that the of the case and bracelet watch be checked once every caused by dust, moisture and 2 to 3 years. Have your 2 - 3 Years p e r s p i r a t i o n , w i p e t h e m w a t c h c h e c k e d b y a n...
Need help?
Do you have a question about the Z46G and is the answer not in the manual?
Questions and answers