Related Manuals for Pulsar 7T62
Summary of Contents for Pulsar 7T62
- Page 1 CAL. 7T62 ALARM & CHRONOGRAPH TIME/CALENDAR Hour, minute and small second hands Date displayed in numerals STOPWATCH Measures up to 60 minutes in 1/5 second increments. Split time measurement SINGLE-TIME ALARM Rings only once at a designated time within the coming 12...
- Page 2 DISPLAY AND CROWN/BUTTONS STOPWATCH STOPWATCH 1/5-second hand minute hand Minute hand Hour hand CROWN Small second hand Date ALARM hour hand ALARM minute hand a: Normal position b: First click c: Second click...
- Page 3 SCREW DOWN CROWN [for models with screw down crown] Unlocking the crown 1 Turn Crown counterclockwise until you no longer feel the threads turning. 2 Crown can be pulled out. Locking the crown 1 Push Crown back in to normal position. 2 Turn Crown clockwise while pressing it lightly until tight.
- Page 4 SETTING THE TIME AND ADJUSTING THE STOPWATCH HAND POSITION This watch is so designed that the following are all made with the crown at the second click position: 1) main time setting 2) alarm hand adjustment 3) stopwatch hand position adjustment Once the crown is pulled out to the second click, be sure to check and adjust 1) and 2) at the same time.
- Page 5 1) MAIN TIME SETTING Hour hand Minute hand Turn to set the hour and CROWN minute hands. * It is recommended that the hands be set to the time a few minutes ahead of the current time, taking into consideration the time required to set the ALARM hands and to adjust the STOPWATCH hand position if necessary.
- Page 6 Hour hand Minute hand Press repeatedly to set ALARM hands to the time indicated by the main time hands. * ALARM hands move quickly if button B is kept pressed. ALARM ALARM hour hand minute hand 3) STOPWATCH HAND POSITION ADJUSTMENT If the STOPWATCH hands are not in the “0”...
- Page 7 Press repeatedly to set STOP- STOPWATCH STOPWATCH WATCH minute hand to the “0” 1/5-second minute hand hand position. * The hand moves quickly if button B is kept pressed. Press for 2 seconds. * STOPWATCH 1/5-second hand turns a full circle. Press repeatedly to set STOP- WATCH 1/5-second hand to the “0”...
- Page 8 ALARM and STOPWATCH hands can be readjusted in the following order by pressing button A for 2 seconds. ALARM STOPWATCH STOPWATCH hands minute hand 1/5-second hand Advance Turns a Turns a 12 hours. full circle. full circle. * After all the adjustments are completed, check that the main time and alarm hands indicate the same time.
-
Page 9: Setting The Date
SETTING THE DATE Before setting the date, be sure to set the main time. CROWN 1 Pull out to first click. 2 Turn clockwise until the desired date appears. 3 Push back in to normal position. Date... - Page 10 STOPWATCH The stopwatch can measure up to 60 minutes in 1/5-second increments. After 60 minutes, it will start counting again from “0” repeatedly up to 12 hours. STOPWATCH 1/5-second hand STOPWATCH minute hand Start / Stop / Restart Reset / Split /Split release...
- Page 11 Before using the stopwatch, be sure to check that the crown is set at the normal position and that the STOPWATCH hands are reset to the “0” position. * If the STOPWATCH hands do not return to the “0” position when the stopwatch is reset to “0”, follow the procedure in “SETTING THE TIME AND ADJUSTING THE STOPWATCH HAND POSITION”.
- Page 12 SINGLE-TIME ALARM The alarm can be set to ring only once at a designated time within the coming 12 hours. The alarm time can be set in one minute increments. ALARM TIME SETTING Before using the alarm, check that the ALARM hands are adjusted to the current time.
- Page 13 Push back in to normal CROWN position. * The alarm is automatically engaged. HOW TO STOP THE ALARM At the designated time the alarm rings for 20 seconds, and it is automatically disengaged as it stops. To stop it manually, press button A or B. HOW TO CANCEL THE ALARM TIME YOU HAVE SET Pull out to first click.
- Page 14 TACHYMETER [for models with tachymeter scale on the dial] To measure the hourly average speed of a vehicle [ Ex. 1 ] Use the stopwatch to determine how many seconds it takes to go 1 km or STOPWATCH 1 mile. second hand: 40 seconds Tachymeter scale indicated by...
- Page 15 “90” (tachymeter scale figure) x 2 (km or mile) = 180 km/h or mph “90” (tachymeter scale figure) x 0.5 (km or mile) = 45 km/h or mph To measure the hourly rate of operation [ Ex. 1 ] Use the stopwatch to measure the STOPWATCH second hand: time required to complete 1 job.
-
Page 16: Notes On Operating The Watch
NOTES ON OPERATING THE WATCH SETTING THE TIME AND ADJUSTING THE STOPWATCH HAND POSITION When the stopwatch is or has been measuring, if the crown is pulled out to the second click, it will automatically reset the STOPWATCH hands to “0”. If the alarm has been set and the crown is pulled out to the second click, the ALARM hands will turn to indicate the current time. - Page 17 STOPWATCH Restart and stop of the stopwatch can be repeated by pressing button A. Measurement and release of split time can be repeated by pressing button B. SINGLE-TIME ALARM The single-time alarm cannot be set for a time more than 12 hours ahead of the current time.
-
Page 18: Battery Change
BATTERY CHANGE Battery life : Approx. 3 years Battery : SEIKO SR927W Years If the stopwatch is used for more than 2 hours a day and/or the alarm rings for more than 20 seconds a day, the battery life may be less than the specified period. As the battery is inserted at the factory to check the function and performance of the watch, its actual life once in your possession may be less than the specified period. - Page 19 * The watch remains accurate while the small second hand is moving at two-second intervals. WARNING Do not remove the battery from the watch. If it is necessary to take out the battery, keep it out of the reach of children.
-
Page 20: To Preserve The Quality Of Your Watch
If the watch becomes wet, we suggest that you Water resistance (10 bar/15 bar/20 bar)* have it checked by an AUTHORIZED PULSAR If “WATER RESISTANT 10 BAR”, DEALER or SERVICE CENTER. “WATER RESISTANT 15 BAR”... - Page 21 * Before using the water resistance 5, 10, 15 or 20 bar watch in water, be sure the crown is pushed in completely. Do not operate the crown when the watch is wet or in water. If used in sea water, rinse the watch in fresh water and dry it completely.
- Page 22 2 - 3 careful not to drop your Years your watch checked by an watch or hit it against hard AUTHORIZED PULSAR surfaces, as this may DEALER or SERVICE CENTER to cause damage. ensure that the case, crown, buttons, CHEMICALS gasket and crystal seal remain intact.