Deze garantie geldt gedurende 12 maanden voor elke fabricagefout aan uw JOY SPORT product die door een gemachtigd JOY SPORT dealer werd verkocht. Wanneer u garantie claimt bied JOY SPORT de mogelijkheid om naar eigen goeddunken het defecte apparaat of het betreffende onderdeel te herstellen of te vervangen.
Page 4
Veligheids instructies Lees de volgende veiligheids punten aandachtig door: 1. Houd kinderen altijd uit de buurt van dit apparaat, de enthousiastheid van kinderen kan leiden tot verkeerd gebruik van dit apparaat, zorg altijd dat wanneer kinderen dit apparaat gebruiken dit gebeurd onder toezicht van een volwassen persoon.
Page 5
1 Gereedschap en Onderdelen: Name en Specificatie Foto Name en Specificatie Foto M8*36 inbusbout M8 gebogen ring M8*6.35T borgmoer OD20*ID8.5*2.0T ring M4*35 schroef M8*20 bout M4*20 schroef M8 borgmoer M10*50 bout M5*16 schroef OD20*ID10.5*2.0T ring 5MM inbussleutel M8*72 inbusbout 6MM inbussleutel Ringsleutel met M8 veerring kruisschroevendraaier...
Page 6
2 Voor stabilisator Plaats de voor stabilisator (52) Op het hoofdframe. Plaats op de twee M8*72 inbusbouten (51) de twee M8 veerringen (17) en dan de twee M8 gebogen ringen (49) plaats deze twee inbusbouten door de voor stabilisator en zet de voor stabilisator vervolgens vast op het hoofdframe.
Page 7
5 Stuurkolom Demonteer de twee M8*68 inbus bouten (48), twee M8 borgmoeren (59), vier M8 veerringen (17), twee M8 gebogen ringen (49), twee M8*20 inbus bouten (16) en de twee OD20*ID8.5*2.0T ringen (15) Welke al zitten voorgemonteerd op de stuurkolom. Schijf nu het beschermkapje (60) op de stuurkolom (46).
Page 8
7. Montage van de bovenste zwenkarm Houd de bovenste zwenkarm (12) dicht bij de onderste zwenkarm (94). Bevestig nu de twee kabels met elkaar. Schuif nu de bovenste zwenkarm op de onderste zwenkarm. Monteer nu een M8*36 inbusbout en gebruik een M8*6.35T borgmoer (9) om de bovenste op de onderste zwenkarm vast te zetten.
Page 9
10. Bidonhouder & Bidon Demonteer de bidonhouder (57) op de stuurkolom. Gebruik twee M5*16 schroeven (36) om de bidonhouder te monteren. Plaats daarne de bidon (58) in de bidonhouder. 11 Uw apparaat aansluiten op het lichtnet Zorg ervoor dat U de adaptor (101) altijd aansluit op het lichtnet met (230V-50HZ).
Page 11
Onderdelenlijst Name & Specificaiton Qty. Name & Specificaiton Qty. Dopje Voor stabilisator Foam Kabel (Computer) Handgreep sensoren Kabel voor de handgreep sensoren Hangreep sensoren schroeven Kabel voor de handgreep sensoren M3*10 Bovenste zwenkarm links Stuur Kabel voor de handgreep sensoren Bidonhouder M8*36 inbusbout Bidon...
Page 12
Handleiding Computer ENTER: 1. Druk op deze knop om de volgende gegevens te bevestigen Year- Month- Date- Hour-Minute and alarm. 2. Druk op deze knop om de volgende functies te selecteren Distance, Time, Calories, T.H.R, Gender, Age, Height, Weight and hart Rate%, de gekozen functie zal in het scherm flikkeren.
Functies 1. Kalender: geeft de datum en de week weer. 2. Temperatuur: Geeft de omgevings temperatuur aan van 10 tot 60 graden. 3. Klok: geeft de tijd weer. 4. Alarm: deze monitor heeft een alarm functie. 5. Scan: geeft alle gegevens tijdelijk weer SPEED- RPM- DIST-TIME-CAL-WATT-PULSE. 6.
Page 14
b. Tijd: De computer zal de tijd optellen van 00:00 tot 99:59 minuten. Gebruiker kan ook zelf de tijd instellen van 1:00 tot 99:00 de monitor zal dan omlaag tellen. Als de ingestelde waarde bereikt is zal de computer een alarm toon geven. c.
Page 15
(De standard ingestelde warden zijn, Geslacht- Man, leeftijd- 30, Hoogte- 175 cm en gewicht -70 kg .) Hierna drukt u op de START/STOP knop om het lichaamsvet te bepalen. Het display zal Body type, Body Fat ratio and BMI aangeven. Druk op een knop om terug te keren naar het hoofddisplay.
Page 16
*Gebruikers programma U1~U4 Druk de ENTER knop om in setting mode te komen. Distance, Time, Calories and T.H.R. Gebruik de UP of DOWN knop om de waarde in te stellen en druk de ENTER knop om elke waarde te bevestigen. Nadat de eerste kolom flikkert, kan de gebruiker de waarden instellen door te drukken op de UP of DOWN knop dan op de ENTER knop drukken om de waarde te bevestigen.
Dear customer, We want to thank you for having chosen a JOY SPORT product, and wish you a lot of fun and success during training with your JOY SPORT exercisers. Please note and follow the enclosed safety and assembly instructions carefully.
General safety instructions In the design and the production of this fitness equipment, much attention has been paid to safety. Nevertheless, you need at all times to remain conscious of certain safety measures. Make certain that you have carefully read through the whole user manual prior to your use of the equipment.
Warning Consult with your physician prior to starting your exercises. A frequent and intensive training programme should first be approved by your family physician. This is especially important for individuals above 35 years of age or for those with physical problems. Carefully read through the entire user manual before you start exercising.
Page 21
Products Overview 手握心跳 Hand pulse 右上扶手 Right upper swing 握把管 Round bar 仪表 Computer 左上扶手 Left upper swing bar 扶手饰盖 Swing bar housing 水壶 Water 下扶手组 Lower swing bar Computer post 仪表杆组 脚踏管饰盖( 右) Left pedal tube cover Right pedal tube cover 脚踏管饰盖( 左) Right pedal 右脚踏板...
2 Front stabilizer Move the front stabilizer (52) close to the front bottom of the main frame. Insert M8*72 inner hexagon screw (51) through the M8 spring washer (17) and M8 acr washer (49) then lock them up. 3. Rear stabilizer Take the rear stabilizer plate (74) close to the rear bottom of the main frame.
5 Meter assembly First please remove two M8*68 inner hexagon screws (48), two M8 nylon caps (59), four M8 spring washers (17), two M8 arc washers (49), two M8*20 inner hexagon screws (16) and two OD20*ID8.5*2.0T flat washers (15) which are pre-assembled at the bottom of the computer post.
Page 25
7. Upper swing bar & lower swing bar Take the right upper swing bar (12) close to the right lower swing bar (94). Then combine the hand pulse wire 1 out of the upper swing bar with the hand pulse 3 out of the lower swing bar.
Page 26
10. Water bottle Attach the water bottle holder (57) on the computer post. Use M5*16 screw (36) to fix it. After this insert the water bottle (58) directly into the holder. 11 Connection with the electricity power The computer can start to run only after you get it with connection with the power.
Parts List Name & Specificaiton Qty. Name & Specificaiton Qty. swing bar end cap front stabilizer swing bar foam computer connecting upper wire hand pulse hand pulse wire 3 hand pulse screw M3*10 hand pulse wire 4 left upper swing bar round bar hand pulse wire 1 water bottle holder...
Page 29
Instruction Manual for Exercise Monitor Key Functions: ENTER: 1. Press this button to confirm the setting value of Year- Month- Date- Hour-Minute and alarm. 2. Press this button to select functions of Distance, Time, Calories, T.H.R, Gender, Age, Height, Weight and hart Rate% to be preset, the chosen function will be blinking. Please note that not all functions can be selected in each program.
Page 30
** KM/MILE SWITCH: During the stop situation, press ENTER and Recovery key and hold 2 seconds then can change from Km to Mile or from Mile to Km automatically. ** CALENDAR SETTING: During the stop situation, press MODE and Recovery keys and hold 2 seconds then can enter setting mode of Calendar.
Page 31
Use up or down key to set the value while the number of year, month, date and time is blinking then press Enter key to confirm each setting value. (If users did not enter any value over 20 seconds, the display will proceed with next step. At this time you can press START and ENTER keys for 2 seconds to enter setting of Calendar &...
Page 32
setting value. Once reach the setting value, the monitor will alarm then stop. If user would like to continue exercise, press Start key then the value will count up from 00:00. c. CAL: The monitor will count up the calories form 0.0 to 999.9 without setting the value. User can set the target value from 10 to 9990 then the monitor will count down form the setting value.
Page 33
each data. (The default values for each data are Gender- Male, Age- 30, Height- 175 cm and weight-70 kgs.) After that press START/STOP key to calculate the body fat and also place your palms on the both of contact pads appropriately. The display will show out Body type, Body Fat ratio and BMI.
Page 34
*User programs of U1~U4 Press ENTER key to enter setting mode to set up Distance, Time, Calories and T.H.R. Use UP or DOWN key to adjust the value and then press ENTER key to confirm each value. After that the first column will be flashing, user can adjust the level of loading by pressing UP or DOWN key then press ENTER key to confirm.