Dear customer, We want to thank you for having chosen a JOY SPORT product, and wish you a lot of fun and success during training with your JOY SPORT exercisers. Please note and follow the enclosed safety and assembly instructions carefully.
INSTRUCTIONS.) You must be able to safely lift 100 pounds ( 46 KGS) in order to raise, lower or move the elliptical exerciser. Do not place object under the elliptical exerciser in an attempt to change the incline of the elliptical exerciser. Inspect and tighten all parts of the elliptical exerciser every three months. This elliptical exerciser is intended for in‐home use only. Do not use this elliptical exerciser in any commercial, rental or institutional setting. Use in any commercial, rental or institutional setting voids the warranty. WARNING: Consult your physician before beginning this or any exercise program. This is especially important for any person over the age of 35 or any person with any pre‐existing health problems. Read all instructions before using. North American/LMX Group assumes no responsibility for personal injury or property damage sustained by or through the use of this product. SAVE THESE INSTRUCTIONS JOY SPORT...
Page 5
Pedal tube cover top (L) Pedal tube cover bottom (L) Pedal tube cover top (R) Pedal tube cover bottom (R) Top step foot cover Bottom step foot cover AC Adaptor Base Frame Pedal tube(R) Pedal tube(L) JOY SPORT...
Page 6
HARDWARE PACKAGE/PARTS/TOOLS hardware box CT-Advanced Rear cover for upright tube X450 Advanced Fix handle bar Up right tube Front cover for upright tube X450 Bottle holder Front stabilizer Rear stabilizer Arm cover front Arm cover rear Console JOY SPORT...
Page 8
3) locking sleeves with tool and cover the nut with two caps (#21) STEP:3 UPRIGHT TUBE ASSY.TO THE FRAME PARTS LIST QUANTITY As photo shown Insert the post joint cover (#5) onto the upright tube (#68) then 1) place upright tube on top of a chair ( or by a second person to assist holding) close to the main frame be facilitated to connect the cables. 2) check the direction of upright tube before connect the Top/Bottom pre‐assembled cables as photo shown. 3) keep the post cover with upper part of the upright tube,fixing six screws (#18) with finger locking first then tighten all firmly. Note! tighten two screws on the label "①" screw hold first and then tighten up the rest of four screws to avoid the hold alignment match problem. PEDAL COVER ASSY ( 一) STEP:4 PARTS LIST QUANTITY As photo shown 1) Set both pedal tube assy (#74/#75) (left/right) on the floor, indentify (right/left)tube. 2) Assembly the top step (#97/#98) with screws (#29 & #30) STEP:5 PEDAL COVER ASSY ( 二)& PEDAL TUBE ASSY. (一) PARTS LIST QUANTITY As photo show 1) Set the pedal tube left & right (#74/#75) to the main frame, secure the pedal tube with main frame with washer (#17) and M10 lock nut (#12) tighten firmly. 2) Set the right pedal tube cover, top "R" (#101) and bottom "R" (#102) with screws (#29). 3) Do the same to tighten up the pedal tube cover, top "L" (#101)and bottom (#102) to the left pedal tube (#74) JOY SPORT...
Page 10
2) Three locations on the swivel tube available adjust to lock with the middle holes for both right/left tubes. STEP:7 UPPER SWING ARM ASSY. PARTS LIST QUANTITY As photo shown 1) Set the swing arm handlebars R/L (#72/#73), insert to both swivel tubes (#69/#70). 2) Turn and match the handlebars with the aligned holes, secure parts (#72/#69) also (#73/#70) with screw (#18) and special spring washer (#A) then flat washer (#65), tighten up both totally. STEP:8 CENTER COVER & BOTTLE HOLDER ASSY PARTS LIST QUANTITY As photo shown 1) Pre‐assemble the rear cover (#94) with bottle holder Grey (#105) with #104 screws (#104) 2) tighten up the front cover (#95) with rear cover (#96) with screws (#29) for both right & left side. Finally secure the font cover A(#93) with rear cover A (#94) with screw (#29) FIX HANDLEBAR ASSY. STEP:9 PARTS LIST QUANTITY As photo shown 1) Fit the fixed handlebar (#71) with screws (#6) and thru the bracket hold of upright tube with screw driver. 2) Set both EKG cables thru the small holes under the fix handlebar (#71) on the #88A/B upright tube, pick up cables from top of the upright tube. 3) Secure the fix handlebar covers (#88A/#88B) with screw (#61) Note: Bottom cover (#88B) got a nut inject in the bar. JOY SPORT...
Page 12
A photo shown 1) Connect cable comes out from console (#43) also cables from the upright tube firmly. Note: check & plug cables, same color to plug together, black color can plug with black no need to select special plug. 2) Insert all plugged cables into the uprught tube, set console (#43) on the top of upright tube, secure with for screws (E) STEP:11 PLASTIC PEDAL ASSY. PARTS LIST QUANTITY As photo shown 1) Set both pedal tube (#74/#75) & plastic pedals(#52) on the floor, There is no difference between the left /right pedals (#52), secure both pedal (#52) to the pedal tube assy.(#74/#75) with screw (#18) from the top. Note! the pedal has left/right label, check the direction of pedal for front and foot protection edge of pedal as drawing shown) 2) There is a stride location adjustable bar (#55) can set with 8 different locations for the stride length, it has to set both left & right bar at the same location ( number shown on the plastic pedals) Note! Three sets of holds on the tube plate, user may choice one set to use, eash set will give one inch variation pedal distance to select, make sure both pedasl select the same location of holes STEP:12 POWER ADAPTOR PARTS LIST QUANTITY As photo shown #106 1) Plug the power cord with power adaptor (#34) into an appropriate outlet IMPORTANT: The elliptical exerciser is not compatible with GFCI‐equipped outlets. 2) The othe r end of the access hole in the rear of the base frame Note! before plug in, please check the voltage specifications on the label. JOY SPORT...
Page 14
Joy Sport CT-Advanced Ⅰ. Power Modes Power On: Plug in the power cord with power adaptor into an appropriate outlet. Next, locate and switch “on” the reset/off button on the frame, near the power cord . A loud beep will sound and the display will then light (Fig.
Page 15
The console is now in Program Selection mode. Press select a preset workout program: Press to confirm your PROGRAM SELECTION. ENTER MANUAL→ PROGRAM→FITNESS→ PERSONAL→H.R.C.→RANDOM ● MANUAL ● PROGRAM ● FITNESS ● PERSONAL ● HRC ●RANDOM JOY SPORT...
Page 16
You can now set up CALORIES Press to adjust target then press to confirm CALORIES set up. ENTER You can now set up PULSE Press to adjust target heart rate then press to confirm PULSE set up. ENTER JOY SPORT...
Page 17
You can now set up CALORIES Press to adjust target then press to confirm CALORIES set up. ENTER You can now set up PULSE Press to adjust target heart rate then press to confirm PULSE set up. ENTER JOY SPORT...
Page 19
40% < FAT ≦ 50% Body Fat Index from American Council on Exercise Classification Women (% Fat) Men (% Fat) Essenti l Fat 10-12 Athletes 14-20 6-13 Fitness 21-24 14-17 Acceptable 25-31 8-25 Obese > 31 > 25 JOY SPORT...
After turning the power on, pressing this button will allow you to directly go into the MANUAL program and start your work out on default settings. 4. + & - These buttons are used to adjust gender (SEX), AGE, HEIGHT (H.t), Weight (W.t), TIME, DISTANCE, CALORIES, Target Heart Rate (H.R.C.), and resistance level (LEVEL) selections. JOY SPORT...
Page 21
0: 00 RPM(每分钟转速) L1 - L24 BRAKE RESISTANCE LEVEL HOW TO USE THE SOUND SYSTEM To play music or audio books through the console sound system while you exercise, plug the included audio cable into the jack on the back of the console and into a jack on your MP3 or IPOD; make sure that the audio cable is fully plugged in. Next, press the play button on your MP3 player or IPOD. Adjust the volume level using the volume control on your MP3 or IPOD. JOY SPORT...
Joy Sport CT-Advanced PARTS LIST Key Number Description Key Number Description Handlebar end cap Belt Handlebar grip End cap T-Bar grip Drive pulley Hand pulse grip unit Pedal, LH Upright Protector Pedal, RH Screw Adjustable foot Locking washer pedal resistance...
Page 25
Joy Sport CT-Advanced PARTS LIST Rear cover for swivel tube front lower cap right Front cover for swivel tube Rear foot cover Top step foot cover Front foot cover (middle) Bottom step foot cover Front foot cover (left) Pedal tube cover top L...
INHOUDSOPGAVE Veiligheidsvoorschrift………………………………………………………………………………..1 Belangrijke veiligheids en Joy sport importeur …………………………………..…. 2‐3 Hoofdbestanddelen.......……………………………………………………………………... 4‐5 Hardware Kit.............…………………………………………......6 Montage instruktie........……………………………..………………………… . .7‐12 Computerhandleid……………………………………………............13‐20 Overzicht..……………………………………………................21 Onderdelenlijst..……………………………………………….……………………………………….22‐23 Transport en opslag........…………….……………………………………...……….24 WARNING DECAL PLACEMENT JOY SPORT...
Deze garantie geldt gedurende 24 maanden voor elke fabricagefout aan uw JOY SPORT product die door een JOY SPORT dealer werd verkocht. Wanneer u garantie claimt bied JOY SPORT de mogelijkheid om naar eigen goeddunken het defecte apparaat of het betreffende onderdeel te herstellen of te vervangen.
Page 30
De gegevens van de computer zijn geen precisie metingen maar enkel een indicatie voor de status van het moment en een hulpmiddel voor de trainingen. Controleer regelmatig of alle delen nog goed bevestigd zitten en waar nodig zorg voor voldoende smering. Waarschuwing:Neem eerst contact op met uw huisarts of er serieuze problemen met uw gezondheid kunnen ontstaan door het gebruik van dit apparaat. Bewaar deze instrukties. JOY SPORT...
Page 34
Onderdeel Aantal 1) Plaats een deel van de verpakking onder frame om montage te vereenvoudigen. 2) Verbind de steun met twee bouten (#19) vulringen (#65) moeren (#20). 3) Zet de moeren goed vast en dek ze af met de kapjes (#21). STAP:3 Montage staander op hoofdframe Nummer Onderdeel Aantal 1) Monteer de afdekkap (#5) over de staander (#68). 2) Houd de onderzijde van de paal tegen framebuis en verbind de kabels. 3) Monteer de 6 schroeven (#18) zet deze eerst allemaal losjes vast en pas daarna vastzetten. Montage Pedaalafdekking STAP:4 Nummer Onderdeel Aantal 1) Monteer op beide pedalen (#74/#75) (links/rechts) de pedaalarm kapjes, let op (linker/rechter). 2) Monteer de afdekkingen (#97/#98) en zet vast met met schroeven (#29 & #30). STAP:5 Montage draaipuntafdekking Nummer Onderdeel QUANTITY 1) Monteer de pedaalbuis links & rechts (#74/#75) op het frame, zet deze vast met vulring (#17) en M10 borgmoer (#12) zet deze goed vast. 2) Monteer rechter pedaalafdekking,boven "R" (#101) en onder "R" (#102) met schroeven(#29). 3) Doe hetzelfde met de linkerpedaal afdekking , boven (#101) en onder (#102). JOY SPORT...
Page 36
(#A) vulring (#65),Goed vastzetten. STAP:8 Montage centrale afdekking & bidonhouder Nummer Onderdeel Aantal 1) Verbind de achterafdekking (#94) met bidonhouder (#105) met de schroeven (#104). #104 2) Verbind de voorafdekking (#95) met achterafdekking (#96) met de schroeven (#29) voor linker en rechterkant, verbind afdekking (#93) met achterafdekking (#94) met de schroeven (#29). Montage handgreep STAP:9 Nummer Onderdeel Aantal 1) Monteer de handgreep (#71) met de schroeven (#6) in de steun op de voorstaander. 2) Schuif beide EKG kabels door het kleine gaatje onder de steun (#71) en pak ze op aan de bovenzijde van de voorstaander. #88A/B 3) Bevestig de handgreep afdekkingen (#88A/#88B) met de schroeven (#6 ). STAP:10 Montage computer Nummer Onderdeel Aantal 1) Verbind de kabels uit de computer (#43) met de kabels uit de voorstaander. Tip: controleer en verbind kabels ,met dezelfde kleur, de zwarten kunnen onderling worden gewisseld. 2) Stop alle kabels weg in de voorstaander en plaats de computer (#43) bovenop de voorstaander en zet deze vast met de schroeven (E). JOY SPORT...
Page 38
STAP:11 Montage kunsstof voetplaat Nummer Onderdeel Aantal 1) Monteer de voetplaat met de vier bouten (#18) ringen (#65) en moeren (#20), 2) Zet deze vast met de bijgeleverde sleutel en dek de moeren af met de sierafdekkingen. STAP:12 Adapter Nummer Onderdeel Aantal 1) Plaats adapter (#92) in geaard stopcontact. #106 2) Plaats de connector in het achtergedeelte van het apparaat. JOY SPORT...
Page 40
Druk om geslacht te bevestigen. ENTER 3. Leeftijd. Display geeft aan “AGE” is leeftijd boven rechts in display. druk om uw leeftijd in te voeren Druk om uw leeftijd te bevestigen. ENTER JOY SPORT...
Page 41
6. Gebruikersinstelling is nu gereed, apparaat nu klaar voor start oefening. U kunt nu een programma selecteren Druk workout programma te selecteren: Druk om ingestelde programma te bevestigen. ENTER MANUAL→ PROGRAM→FITNESS→ PERSONAL→H.R.C.→RANDOM ● MANUAL ● PROGRAM ● FITNESS ● PERSONAL ● HRC ●RANDOM JOY SPORT...
Page 42
DISTANCE te bevestigen. ENTER Wijzigen van CALORIEN Druk naar gewenste waarde en druk om CALORIES te bevestigen. ENTER Wijzigen hartslag. Druk naar gewenste waarde en druk om PULSE te bevestigen. ENTER JOY SPORT...
Page 43
ENTER Wijzigen CALORIEN Druk naar gewenste waarde en druk om CALORIES te bevestigen. ENTER Wijzigen hartslag Druk naar gewenste waarde en druk om PULSE te bevestigen. ENTER JOY SPORT...
Page 46
Na starten kan door indrukken van deze knop het programma direct gestart worden met de opgeslagen waarden. 4. + & - Deze knoppen worden gebruikt om warden te verhogen of te verlagen. 5. ENTER Wordt gebruikt om een instelling te bevestigen. JOY SPORT...
Page 47
0 - 250 rpm 0: 00 RPM(每分钟转速) L1 - L24 BRAKE RESISTANCE LEVEL Hoe het muzieksysteem te gebruiken Om muziek af te spelen plugt u de kabel van uw MP3 speler of IPOD in op de achterzijde van de console. Door inschakelen van de speler kan muziek worden afgespeeld en het volume dient ook vanaf uw apparaat te worden ingesteld. JOY SPORT...