Cancelling Timecode Offset; Setting Timecode Offset "On The Fly; Park Position; Automatic Park Position Setting - Tascam DA-78HR Owner's Manual

9 - Operations related to timecode
4 Use the
and keys to set the offset for the
slave DA-78HR, and the
keys to move the cursor to the different fields.
OFFSET
You can also use the
cursor key.
The front panel OFFSET
when an offset value has been set.
See 4.3.5, ""Left" and "right" keys" for details
of setting values in a time field. You can set the
offset to sub-frame (percentage or sample)
accuracy.
5 You can also change the sign of the offset value
to a minus value by moving the cursor to the
appropriate position and using the
keys.

9.6.4 Cancelling timecode offset

To cancel the offset, simply set the offset value to
.
1 Enter the offset setting, as described above.
2 Press and hold down the
key to reset the value.
Timecode offset will now be cancelled and the
OFFSET
front panel indicator will go out.
9.6.5 Setting timecode offset "on the
fly"
As well as entering an absolute number, it is also pos-
sible to enter a number "on the fly" as the tapes are
playing.
1 Locate the two devices (master and slave DA-
78HR) so that they have the right offset, either
by playing the tapes and pausing them or carry
out the next operation while one or both tapes
is being played back.
2 On the slave DA-78HR, press and hold the
SHIFT key, and press the
OFFSET
( ) key at the correct offset time to cap-
ture and store the offset.
The display will briefly show
OFFSET
), and the current difference between
the master unit and slave DA-78HR will be
stored as an offset.

9.6.6 Park position

When the DA-78HR is slaved to an external time-
code source, it will take some time between the mas-
ter unit starting to play and starting to transmit
timecode for the DA-78HR to read.
59
TASCAM DA-78HR
SHIFT ed and
key as a right
indicator will light
and
key and press the
AUTO IN/OUT
AT
(
These functions allow you to measure and test the
optimum pre-roll position for the DA-78HR (when it
is a timecode slave) to park itself relative to the mas-
ter timecode device so that it will lock up and start
playing quickly.
1 Press the
SHIFT key so that the
is flashing, then press the
display shows
2 Press the
SUB MENU
PARK POS

shows

(
then changes to
current setting, shown in seconds and frames.
3 Use the
and keys to adjust the value
(maximum is 1 second and 29 frames)

9.6.7 Automatic park position setting

When the DA-78HR is acting as a timecode slave, it
can automatically determine the optimum park pre-
roll position to sync with the master.
1 Turn the DA-78HR's
make sure that the time mode is set to TC.
2 Press the
SHIFT key so that the
is flashing, then press the
display shows
3 Press the
SUB MENU
shows
and then changes to
4 Play and stop the master tape.
5 Use the
or key to turn the park test on.
The DA-78HR will then rewind so that the rel-
ative difference is zero. When the DA-78HR
has stopped, go on to the next step below.
6 Play the timecode master.
When the value shown on the display has
stopped changing and is stabilized, go on to the
next step below.
7 Use the
or key to turn the park test off.
The display shows
optimum park pre-roll time for the timecode
master is now stored.

9.6.8 Absolute and relative difference

The offset as set above ("Timecode offset" on
page 58) can be called the "absolute difference"
between the two times. However, if the slave
machine "wanders" (actually, this is unlikely), the
offset (theoretical difference) will not be equal to the
SHIFT indicator
MENU
key until the
TC CHS--
( ).
key so that the display
) briefly, and
( PRK ) followed by the
CHASE on, if it is off and
SHIFT indicator
MENU key until the
TC CHS--
( ).
key so that the display
( PK POS TST ) briefly,
OFF
( ).
DONE
( ), and the