Table of Contents
Advertisement
Quick Links
Instructions – Parts List
Parts
PORTABLE, AIR-ASSISTED AIRLESS
10:1 Ratio Monarkr
Hydra-Sprayr Pumps
95 psi (0.66 MPa, 6.6 bar) MAXIMUM AIR INLET PRESSURE
950 psi (6.6 MPa, 66 bar) MAXIMUM FLUID WORKING PRESSURE
Model 231158
For cold spray applications. Includes pump, cart, hose, gun and tip
Model 231162, Series B
For cold spray applications. Includes pump, cart,
fluid regulation kit 222564, hose, gun and tip
Model 224629, Series A
For heated spray applications. Includes pump, cart,
Viscon@ heater, heater mounting kit 222262,
and circulating kit 222436
Model 231161
For heated spray applications. Includes pump, cart,
Viscon@ heater, heater mounting kit 222262,
circulating kit 222436, hose, gun and tip
Read warnings and instructions.
See page 2 for table of contents.
GRACO INC. P.O. BOX 1441 MINNEAPOLIS, MN 55440-1441
Copyright 1988, Graco Inc. is registered to I.S. EN ISO 9001
307929J
Model 231158 Shown
Advertisement
Table of Contents
Related Manuals for Graco 231161
Summary of Contents for Graco 231161
- Page 1 222436, hose, gun and tip Read warnings and instructions. See page 2 for table of contents. Model 231158 Shown GRACO INC. P.O. BOX 1441 MINNEAPOLIS, MN 55440-1441 Copyright 1988, Graco Inc. is registered to I.S. EN ISO 9001...
- Page 2 D This equipment is for professional use only. D Read all instruction manuals, tags, and labels before operating the equipment. D Use the equipment only for its intended purpose. If you are uncertain about usage, call your Graco distributor. D Do not alter or modify this equipment. Use only genuine Graco parts and accessories.
- Page 3 Permanently coupled hoses cannot be repaired; replace the entire hose. D Use only Graco approved hoses. Do not remove any spring guard that is used to help protect the hose from rupture caused by kinks or bends near the couplings.
- Page 4 WARNING FIRE AND EXPLOSION HAZARD Improper grounding, poor ventilation, open flames or sparks can cause a hazardous condition and result in a fire or explosion and serious injury. D Ground the equipment and the object being sprayed. Refer to Grounding on page 5. D If there is any static sparking or you feel an electric shock while using this equipment, stop spray- ing immediately.
- Page 5 5. Air compressor: follow manufacturer’s recommen- dations. Accessories mentioned in the text are available from your Graco distributor. If you supply your own acces- 6. Spray gun: grounding is obtained through connec- sories, be sure they are adequately sized to meet your tion to a properly grounded fluid hose and pump.
- Page 6 Installation Air Line Filter Main Air Line Air Line Lubricator Fluid Hose Spray Gun Gun Air Supply Hose G Bleed-Type Master Air Valve (for accessories) Ground Wire (required) Pump 22 Suction Hose 23 Suction Tube 25 Fluid Filter 31 Air Regulators 52 Air Relief Valve 62 Bleed-Type Master Air Valve (for pump)
-
Page 7: Model
Installation Installing Fluid Regulation Kit 222564 Connect the gun air supply hose (F) between the air inlet of the gun (E) and the outlet nipple of the gun (Pump Model 231162) (left) air regulator. See Fig. 2. WARNING Connect the fluid hose (D) between the gun fluid inlet and the outlet nipple (66b) of the fluid regulation kit. -
Page 8: And Circulating Kit
Installation Converting the Pump to a Heated NOTE: Reference numbers marked with an asterisk (for example, 68*) are included in kit 222262. Circulating System Apply 110110 pipe sealant (included in the kit) to all To convert pump Model 231162 to a heated circulating male threads, except at swiveling connections. - Page 9 Installation 5. Screw the check valve (70*) into the pump’s fluid outlet, making certain that the arrow on the check valve points away from the pump. Screw the rigid end of the adapter (71*) onto the check valve. See Fig. 5. 6.
-
Page 10: Model
Installation Installing Circulating Kit 222436 4. Screw one of the nipples (41{) into the outlet in the base of the back pressure regulator (83{), then screw one of the elbows (40{) onto the nipple so WARNING the male end of the elbow faces forward. Install another elbow (40{) in the inlet of the back pres- Before installing the heater, heater mounting kit sure regulator, then install the other nipple (41{) in... -
Page 11: Warnings
4. See Fig. 6. (refer to page 12 for Models 231162, 224629 and 231161). Order the parts listed, and perform the as- 2. Install a 101180 Gauge (P) and 100509 Plug (Q) sembly procedure. - Page 12 Installation Model 231162 (Refer to Figs. 6 and 7, and the Parts Models 224629 and 231161 (Refer to Figs. 6 and 7, Drawing on page 18) and the Parts Drawing on page 20) WARNING WARNING Before performing this procedure, follow the Pres- Before performing this procedure, follow the Pres- sure Relief Procedure on page 14.
- Page 13 Filter (For All Models Except 231162) Regulator (Model 231162 Only) 0869B DETAIL C: Fluid Return Connections at Back Pres- sure Valve (Models 224629 & 231161 Only) 0976 DETAIL D: Assembly of Hoses and Gun (Models 231158 and 231162 Only) 0871A...
- Page 14 Operation Pressure Relief Procedure Flush the Pump Before Using WARNING Pumps are tested with lightweight oil which is left in to protect the pump parts. To prevent contamination of INJECTION HAZARD the fluid, flush the pump with a compatible solvent Fluid under high pressure can be in- before using it.
- Page 15 The back pressure regulator (83) used on models 224629 and Shutdown and Care 231161 does the same by requiring a minimum flow rate and also setting the minimum circulating rate WARNING needed to prevent fluid from settling.
- Page 16 Parts Model 231158 7 (REF) 33 (REF) See Detail Above For Parts 0979B 16 307929...
- Page 17 Parts Model 231158 Part No. Description Part No. Description 100016 LOCKWASHER, spring;1/4” 101180 GAUGE, pressure, air; 100022 CAPSCREW, hex hd; 0–200 psi (0–14 bar) 1/4–20 x 3/4” long 102254 SCREW, hex hd; 1/4–20 x 7/8” long 100015 NUT, hex; 1/4–20 166999 ELBOW, street, reducing;...
- Page 18 Parts Model 231162, Series B Ref. No. 66 Fluid Regulation Kit includes items 66a–66q 7 (REF) See Detail At Left For Parts 27 29 30 31 (REF) 33 (REF) 0980B 18 307929...
- Page 19 Parts Model 231162, Series B Part No. Description Part No. Description 100016 LOCKWASHER, spring; 1/4” 158491 NIPPLE; 1/2 npt; 1–5/8” long 100022 CAPSCREW, hex hd; 107142 VALVE, air, bleed-type; 1/2 npt (m x f) 1 1/4–20 x 3/4” long 150286 ADAPTER;...
- Page 20 Parts Model 224629, Series A Includes items 1–83 Model 231161 Includes items 1–92 See Detail At Left For Parts 7 (REF) (REF) 27 29 33 (REF) 22 (REF) Ref. No. 85 Hose Kit Includes Items 86–92 7 (REF) Part Of...
- Page 21 Parts Model 224629, Series A Includes items 1–83 Model 231161 Includes items 1–92 Part No. Description Part No. Description 100016 LOCKWASHER, spring; 1/4” 159801 UNION, adapter, 90_; 100022 CAPSCREW, hex hd; 3/8 npt(f) x 1/2 npsm(f) swivel 1/4–20 x 3/4” long 158683 ELBOW, 90_;...
- Page 22 Notes 22 307929...
-
Page 23: Technical Data
Conversion Kits Heater Mounting Kit 222262 Circulating Kit 222436 Required to convert Model 231158 to a circulating unit. Consists of: Required to convert Model 231158 to a heated unit. Consists of: Ref. No. Ref. No. Ref. No. Ref. No. Also includes 6 ml supply of sst pipe sealant 110110. Kit 222436 includes some parts not required for this pump: 156953 Mounting Stud, 100639 Lockwashers, Also includes 6 ml supply of sst pipe sealant 110110. -
Page 24: Graco Information
With the exception of any special, extended, or limited warranty published by Graco, Graco will, for a period of twelve months from the date of sale, repair or replace any part of the equipment determined by Graco to be defective.