Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Related Manuals for Cornelius JT20D
Summary of Contents for Cornelius JT20D
- Page 1 OPERATORS MANUAL JT20D ETSPRAY ISUAL ISPLAY ISPENSER Release Date: June 27, 2008 Publication Number: 620920865INS Revision Date: March 13, 2019 Revision: C Visit the Cornelius web site at www.cornelius.com for all your Literature needs.
-
Page 2: Contact Information
Commercial Warranty. Cornelius will not be responsible for any repair, replacement or other service required by or loss or damage resulting from any of the following occurrences, including but not limited to, (1) other than normal and proper use and normal... -
Page 3: Table Of Contents
Setting Up Your JT20D ........ - Page 4 Publication Number: 620920865 - 2 - © 2018, Cornelius Inc.
-
Page 5: Safety Instructions
Only trained and certified electrical, plumbing and refrigeration technicians should service this unit. ALL WIRING AND PLUMBING MUST CONFORM TO NATIONAL AND LOCAL CODES. FAILURE TO COMPLY COULD RESULT IN SERIOUS INJURY, DEATH OR EQUIPMENT DAMAGE. © 2018, Cornelius Inc. - 1 - Publication Number: 620920865... -
Page 6: Safety Precautions
NOTE: Many units incorporate the use of additional equipment such as ice makers. When any additional equipment is used, you must check with the equipment manufacturer to determine the additional weight that the counter will need to support to ensure a safe installation. Publication Number: 620920865 - 2 - © 2018, Cornelius Inc. -
Page 7: Power And Water
ATER Power The JT20D requires a 120 Volt, 60Hz grounded receptacle for proper operation, grounding and safety. NOTE: If the colors of the wires in the main leads of this unit do not correspond with the colored marking identifying the terminals in your plug, process as follows. - Page 8 Operators Manual Publication Number: 620920865 - 4 - © 2018, Cornelius Inc.
-
Page 9: Introduction
Operators Manual INTRODUCTION The JT20D Dispenser is a counter top visual display action beverage dispenser. It is designed to dispense a variety of products. It dispenses fruit juice, lemonade or other non-carbonated drinks. PECIFICATIONS Power Cord 7 ft. w/ground connection (2.1 meters) Size 16 in. -
Page 10: Machine Clearance
Operating: 60 ° F (16 ° C) to 110 ° F (43 ° C) Storage: Above 20 ° F (-7 ° C) with bowl empty and dry. Humidity: Below 95% Publication Number: 620920865 - 6 - © 2018, Cornelius Inc. -
Page 11: Installation And Operating Instructions
B. Grasp the clips on the handle. Squeeze clips until they are free from the panel. Pull straight down on the handle. 2. Disassemble the bowl, lid, gasket. and pump housing assemblies. CAUTION: Abrasive cleaners scratches the plastic parts. DON’T USE abrasive cleaners. © 2018, Cornelius Inc. - 7 - Publication Number: 620920865... -
Page 12: To Assemble
5. Slide bowl over the cooling dome and assemble the bowl to the dispenser. Be careful not to wrinkle the gasket. If gasket is wrinkled, beverage will leak out of bowl. See Figure 4. Cooling Dome Figure 4. Publication Number: 620920865 - 8 - © 2018, Cornelius Inc. - Page 13 Figure 7. 9. Replace push handle and pinch tube. A. Push the handle assembly straight up through the rectangular hole until the clips snap into place see Figure 8. Figure 8. © 2018, Cornelius Inc. - 9 - Publication Number: 620920865...
-
Page 14: Operating Procedures
NOTE: If unit is to be used to dispense beverage from only one bowl, use right hand bowl, but add a gallon of water to left bowl to assure proper cooling. 3. The thermostat is preset at the factory and does not normally require resetting by owner. Publication Number: 620920865 - 10 - © 2018, Cornelius Inc. -
Page 15: Frequent Maintenance Procedures
2. To replace the condensate drains, hold the drain against the front panel under the rectangular hole (opening in side of drain should be toward front panel). Push up through the hole until the drain snaps into place see Figure 11. Towards Front Panel Figure 11. © 2018, Cornelius Inc. - 11 - Publication Number: 620920865... -
Page 16: Sanitizing The Unit
2. Be sure gasket has been installed properly. Check gasket for tears or cuts in the rubber.Tears cause leaks in the gasket. 3. Remove and inspect pinch tube for holes. Figure 12. Model JT20D Wiring Diagram (Rev 8) Publication Number: 620920865 - 12 -... - Page 18 Cornelius Inc. www.cornelius.com...
Need help?
Do you have a question about the JT20D and is the answer not in the manual?
Questions and answers