Page 1
PNOZ m EF 16DI Configurable control systems PNOZmulti 2 Operating Manual 1002703-EN-03...
Page 2
Preface This document is a translation of the original document. All rights to this documentation are reserved by Pilz GmbH & Co. KG. Copies may be made for internal purposes. Suggestions and comments for improving this documentation will be gratefully received.
Connecting the base unit and expansion modules Section 6 Commissioning General wiring guidelines Connection Download modified project to the PNOZmulti system Section 7 Operation Messages Section 8 Technical details Safety characteristic data Section 9 Order reference Product Accessories Operating Manual PNOZ m EF 16DI 1002703-EN-03...
Introduction Introduction Validity of documentation This documentation is valid for the product PNOZ m EF 16DI. It is valid until new docu- mentation is published. This operating manual explains the function and operation, describes the installation and provides guidelines on how to connect the product.
Page 5
Introduction INFORMATION This gives advice on applications and provides information on special fea- tures. Operating Manual PNOZ m EF 16DI 1002703-EN-03...
Expansion module PNOZ m EF 16DI Jumper Unit features Using the product PNOZ m EF 16DI: Expansion module for connection to a base unit from the configurable control system . The product has the following features: Can be configured in the PNOZmulti Configurator 16 inputs for connecting, for example: –...
In order to achieve the re- quired safety level for the overall plant/machine, define the safety requirements for the plant/machine and then define how these must be implemented from a technical and organ- isational standpoint. Operating Manual PNOZ m EF 16DI 1002703-EN-03...
Do not open the housing or make any unauthorised modifications. Please make sure you shut down the supply voltage when performing maintenance work (e.g. exchanging contactors). Operating Manual PNOZ m EF 16DI 1002703-EN-03...
Calculation of the maximum reaction time between an input switching off and a linked out- put in the system switching off is described in the document "PNOZmulti System Expan- sion". Block diagram Input Operating Manual PNOZ m EF 16DI 1002703-EN-03...
Connect the base unit and the expansion modules as described in the operating manuals for the base modules. The terminator must be fitted to the last expansion module Install the expansion module in the position configured in the PNOZmulti Configurator. Operating Manual PNOZ m EF 16DI 1002703-EN-03...
Page 12
Please refer to the document "PNOZmulti System Expansion" for details of the number of modules that can be connected to the base unit and the module types. Operating Manual PNOZ m EF 16DI 1002703-EN-03...
PNOZmulti Configurator. Proceed as described in the operat- ing instructions for the base unit. NOTICE For the commissioning and after every program change, you must check whether the safety devices are functioning correctly. Operating Manual PNOZ m EF 16DI 1002703-EN-03...
Expansion module PNOZ m EF 16DI is running without error Expansion module PNOZ m EF 16DI is in a STOP condition Internal error on the expansion module PNOZ m EF 16DI or on the overall system. Expansion module is in a safe condition.
In accordance with the standard EN 60068-2-6 Frequency 5,0 - 150,0 Hz Acceleration Shock stress In accordance with the standard EN 60068-2-27 Acceleration Duration 11 ms Max. operating height above sea level 2000 m Operating Manual PNOZ m EF 16DI 1002703-EN-03...
Page 16
Spring-loaded terminals: Terminal points per connec- tion Stripping length with spring-loaded terminals 9 mm Dimensions Height 101,4 mm Width 22,5 mm Depth 120,0 mm Weight 95 g Where standards are undated, the 2012-08 latest editions shall apply. Operating Manual PNOZ m EF 16DI 1002703-EN-03...
A safety function's SIL/PL values are not identical to the SIL/PL values of the units that are used and may be different. We recommend that you use the PAScal software tool to calculate the safety function's SIL/PL values. Operating Manual PNOZ m EF 16DI 1002703-EN-03...
751 004 Set screw terminals 1 set of screw terminals 750 004 Terminator, jumper Product type Features Order No. PNOZ mm0.xp connector Jumper yellow/black to connect the modules, 10 piece 779 260 left Operating Manual PNOZ m EF 16DI 1002703-EN-03...
Page 19
Back cover Support Technical support is available from Pilz round the clock. Americas Australia Scandinavia Brazil +61 3 95446300 +45 74436332 +55 11 97569-2804 Spain Canada Europe +34 938497433 +1 888-315-PILZ (315-7459) Austria Switzerland Mexico +43 1 7986263-0 +41 62 88979-30...