Download  Print this page

Advertisement

System
Operating Manual
FUJITSU Workstation CELSIUS
W570 / W570power / W570power+
W580 / W580power / W580power+

Advertisement

Table of Contents

   Summary of Contents for Fujitsu CELSIUS W570power

  • Page 1 System Operating Manual FUJITSU Workstation CELSIUS W570 / W570power / W570power+ W580 / W580power / W580power+...
  • Page 2 Thank you for buying an innovative product from Fujitsu. Latest information about our products, useful tips, updates etc. is available on our website: "http://www.fujitsu.com/fts/" You can find driver updates at: "http://support.ts.fujitsu.com/download" Should you have any technical questions, please contact: •...
  • Page 4 Published by / Contact address in the EU Fujitsu Technology Solutions GmbH Mies-van-der-Rohe-Straße 8 80807 Munich, Germany "http://www.fujitsu.com/fts/" Copyright © Fujitsu Technology Solutions GmbH 2.018. All rights reserved. Publication Date 07/2018 Order No.: A26361-K1446-Z320-1-7619, edition 2...
  • Page 5 FUJITSU Workstation CELSIUS W570 / W570power / W570power+ W580 / W580power / W580power+ Operating Manual Your CELSIUS... Ports and Operating Elements Important notes Getting started Operation Troubleshooting and tips System expansions Technical data Index...
  • Page 6 Notes on the product description are consistent with Fujitsu´s design specifications and are made available for comparison purposes. The actual results may differ due to several factors. Technical data is subject to change without notification. Fujitsu does not accept any responsibility for technical or editorial errors nor for omissions.
  • Page 7: Table Of Contents

    No mouse pointer displayed on the screen ..........31 Fujitsu...
  • Page 8 Desktop CELSIUS W570power+, with both installation kits) ....... . .
  • Page 9 Index ................. . 83 Fujitsu...
  • Page 10 Contents Fujitsu...
  • Page 11: Your Celsius

    BIOS manual for your device • • in the operating manual for the monitor • in the manual for the mainboard • in the documentation for your operating system in the information files (e.g. *.PDF, *.HTML, *.DOC, *.CHM, *.TXT, *.HLP) • Fujitsu...
  • Page 12: Notational Conventions

    Validity of the Reference Manual This Reference Manual is valid for the following systems: • FUJITSU Workstation CELSIUS W570 • FUJITSU Workstation CELSIUS W570power • FUJITSU Workstation CELSIUS W570power+ • FUJITSU Workstation CELSIUS W580 FUJITSU Workstation CELSIUS W580power •...
  • Page 13: Ports And Operating Elements

    In order to use a headset, connect the 4 = Slot for memory cards (format: SD headset with both connections. Secure Digital card) 8 = Latch with optional casing lock 5 = USB connection 3.1 with a charging function (USB Type-C™) Fujitsu...
  • Page 14: Rear

    Ports and Operating Elements Rear 1 = Device for a Security Lock 4 = Ports for external devices (device-dependent) 2 = Holes for a padlock 5 = Slot covers 3 = Alternating voltage socket (AC IN) Fujitsu...
  • Page 15: Important Notes

    If the device is brought from a cold environment into the room where it will be used, condensation may occur. Before operating the device, wait until it is absolutely dry and has reached approximately the same temperature as the installation site. Fujitsu...
  • Page 16: Cleaning The Device

    Use disinfectant wipes to clean the keyboard and the mouse. Energy saving, disposal and recycling Disposal Energysaving Recycling You can find information on these subjects in the "Environment and Energy Information" manual or on our website ("http://www.fujitsu.com/fts/about/fts/environment-care/"). Fujitsu...
  • Page 17: Getting Started

    Drives and boards If you have received drives or boards with your device, please do not install them until after first-time setup. How to install drives and boards is described in the "System expansions", Page 33 chapter. Fujitsu...
  • Page 18: Setting Up The Device

    A minimum distance of 200 mm / 7.87 in from the device must be observed for ventilation areas. Do not stack several devices on top of each other. Do not expose the device to extreme ambient conditions (see "Technical data", Page section "Ambient conditions"). Protect the device against dust, humidity and heat. Fujitsu...
  • Page 19: Connecting The Device To The Mains Supply

    Russia and the Commonwealth of Independent States (CIS), large parts of Europe, parts of South America, the Middle East, parts of Africa, Hong Kong, India, large parts of South Asia. UK, Ireland, Malaysia, Singapore, parts of Africa China, Australia, New Zealand Fujitsu...
  • Page 20: Connecting External Devices

    Do not connect or disconnect cables during a thunderstorm. Always take hold of the actual plug when disconnecting a cable. Never pull the cable! To ensure that your device works properly, use only the supplied connection cable or only use a high-quality connection cable. Fujitsu...
  • Page 21: Ports On The Device

    VGA monitor connection, blue DisplayPort Monitorport DVI-I monitor port SD Card (slot for memory cards in the format Secure Digital Card) Some of the connected devices require special software (e.g. drivers) (refer to the documentation for the connected device and operating system). Fujitsu...
  • Page 22: Connecting A Monitor

    (e.g. connecting cables). ► Connect the data cable to a suitable monitor port of the device (VGA, DVI-I, DisplayPort). ► Depending on the connector and configuration level of your device, plug the monitor power cable into an earthed mains outlet (1). Fujitsu...
  • Page 23: Connecting The Mouse

    For an exact description of how to connect external devices to the corresponding port, please refer to the documentation of the external device. Port settings Parallelport Serialport, You can change the port settings (e.g. address, interrupt) in the BIOS Setup. Fujitsu...
  • Page 24: Connecting External Devices To The Usb Ports

    Contact your network administrator if you have any questions about these settings. When you switch on the device for the first time, the supplied software is installed and configured. Plan a reasonable amount of time for this, as this process must not be interrupted. Fujitsu...
  • Page 25: Switch On The Monitor And The Machine

    You will find more information on the system, as well as drivers, utilities and updates on the optional "Drivers & Utilities" DVD and on the Internet at "http://www.fujitsu.com/fts/support". You can find information and help on the Windows operating system functions on the Internet at "http://windows.microsoft.com".
  • Page 26: Operation

    Warning, this could lead to a loss of data! ► Press the ON/OFF switch for at least 4 seconds.  The device will switch off. When you next restart the device, error messages may be displayed due to the improper shutdown. Fujitsu...
  • Page 27: Indicators On The Device

    The device is switched off or disconnected from the mains. If the device is ready for operation, it can be switched on with the ON/OFF switch. Hard disk indicator The indicator lights up when the hard disk drive of the device is accessed. Fujitsu...
  • Page 28: Keyboard

    With some keyboards the ON/OFF switch can only be used with an ACPI (Advanced Configuration and Power Management Interface). Otherwise the key is inoperative. The mainboard must support this function. Keys, Keys, Keys, Enter key confirms the highlighted selection. The Enter key is also referred to as the "Return" key. Fujitsu...
  • Page 29: Settings In Bios Setup

    In BIOS Setup, you can set the system functions and the hardware configuration of the device. When the PC is delivered, the default entries are valid (see "BIOS Setup" manual or manual for the mainboard). You can customise these settings to your requirements in the BIOS Setup. Fujitsu...
  • Page 30: Property And Data Protection

    You can also combine these functions. Anti-theft protection and lead-sealing Device, Device, Casing, Lead-sealing Anti-theftprotection KensingtonLock Chain 1 = Holes for a padlock 2 = Device for a security lock Fujitsu...
  • Page 31: Mechanical Casing Lock (optional)

    The keys can be found on the rear panel of your device. FUJITSU Workstation CELSIUS W570power+ / W580power+: If you have a casing with a casing lock, the cover of the drive cage on the front of the device is also secured against unauthorised opening when the lock is locked.
  • Page 32: Bios Setup Security Functions

    Operation of a SmartCard reader with a RFID reader is not permitted in Taiwan. ► Connect the external SmartCard reader to your system as described in the instructions for the SmartCard reader. SmartCard reader,  After the device is switched on, you will be prompted to insert your SmartCard. Fujitsu...
  • Page 33: Troubleshooting And Tips

    ► Contact the Service Desk responsible for your country for clarification of the problem: "http://support.ts.fujitsu.com/contact/servicedesk". When you do this, please have ready the ID number and serial number of your system.
  • Page 34: The Device Cannot Be Switched Off With The On/off Switch

    ► Restart the system. Incorrect setting for the monitor ► Press while the system is booting. ► Start the system in Safe Mode. ► Set up the monitor as described in the documentation for your operating system and monitor. Fujitsu...
  • Page 35: No Mouse Pointer Displayed On The Screen

    Installing new software When installing programs or drivers, important files may be overwritten and modified. To be able to access the original data in the event of any problems following installation, you should backup your hard disk prior to installation. Fujitsu...
  • Page 36: Tips

    Troubleshooting and tips Tips Topic Out of system resources ► Close unnecessary applications. ► Run the applications in a different order. Fujitsu...
  • Page 37: System Expansions

    The following illustrations may differ slightly from your device, depending on its configuration level. Nachfolgend ist in der Regel die FUJITSU Workstation CELSIUS W570power+ / W580power+ abgebildet. Auf Unterschiede zwischen den drei Gerätevarianten FUJITSU...
  • Page 38: Information About Boards

    The equipment and tools you use must be free of static charges. • Only touch or hold the boards by the edge or, if present, at the areas marked green (Touch Points). • Never touch pins or conductors on boards fitted with ESDs. Fujitsu...
  • Page 39: Opening The Casing

    ► On devices with a casing lock: Unlock the casing. ► Lay the device on its side in the manner shown. ► Pull the locking device (1) and swivel the side part in the direction of the arrow (2). Fujitsu...
  • Page 40: Closing The Casing

    (b). Otherwise the casing cannot be closed. ► Swivel the side cover in the direction of the arrow (1) until it engages. ► On devices with a casing lock: Lock the casing. ► Reconnect the cables that you disconnected before. Fujitsu...
  • Page 41: Open And Close The Drive Cage

    FUJITSU Workstation CELSIUS W570power+ / W580 power+) For some of the work steps described below, the FUJITSU Workstation CELSIUS W570power+/ W580powert+ requires that the drive cage should be opened and, if necessary, also pulled out of the casing.
  • Page 42: Open The Drive Cage

    ► Access this from the side, reaching into the opening on the drive cage (1). ► Remove the cover (2). ► Release the lever from the cover (1). ► Pull the lever (2). ► Fold the cover in the direction of the arrow (3). Fujitsu...
  • Page 43: Pull The Drive Cage Out Of The Casing

    Pull the drive cage out of the casing. ► Open the drive cage (see "Open the drive cage", Page 38). ► Fold upwards the lever on the drive cage (1). ► Pull the drive cage out of the casing using the lever (2). Fujitsu...
  • Page 44: Slide The Drive Cage Into The Housing

    Slide the drive cage into the housing. ► Slide the drive cage into the housing (1). ► Fold the lever on the drive cage back into the cage (2). ► Close the drive cage (see "Close the drive cage", Page 41). Fujitsu...
  • Page 45: Close The Drive Cage

    System expansions Close the drive cage ► Fold the cover upwards (1). ► Attach the lever to the cover (2). ► Position the cover on the drive cage (1). ► Close the casing (see "Closing the casing", Page 36). Fujitsu...
  • Page 46: Overview Of The Drive Bays And Drives In Your Device

    (see "Removing an accessible drive", Page 47). ► Take the drive cover (a) out of the holder in the direction of the arrow (1). ► Attach the drive cover (a) to the slim-line drive (b). Fujitsu...
  • Page 47: Removing An Accessible Drive

    ► Press the release button (1). ► Press the clip (a) in the direction of the arrow (2).  The drive will be pushed forward out of the slot. ► Pull the drive out of the casing in the direction of the arrow (3). Fujitsu...
  • Page 48 fire protection and to prevent foreign objects from getting into the casing. ► Close the casing (see "Closing the casing", Page 36). It may be necessary to modify the entry for the drive in the BIOS Setup. Fujitsu...
  • Page 49: Installing And Removing The Accessible 5

    Proceed as follows: ► Open the casing (see "Opening the casing", Page 35). ► Remove the drive cover from the bracket in the direction of the arrow (1). ► Connect the drive cover to the drive (1). Fujitsu...
  • Page 50: Installing An Accessible Drive

    ► Slide the accessible drive into the casing until it snaps in place (1). ► Connect the cables to the drive. Make sure the polarity is correct. ► Close the casing (see "Closing the casing", Page 36). It may be necessary to modify the entry for the drive in the BIOS Setup. Fujitsu...
  • Page 51: Removing An Accessible Drive

    ► Remove the drive cover from the drive (1). ► Place the drive cover on the holder in the direction of the arrow (1). ► If necessary, make the required settings on the remaining hard disk drives. ► Close the casing (see "Closing the casing", Page 36). Fujitsu...
  • Page 52: Overview Of The Hard Disk Drives

    Overview of the hard disk drives The EasyChange rails for the installation are provided together with the particular drive or installation kit. FUJITSU Workstation CELSIUS W570 / W570power / W580 / W580power No. Upgrade options Reference One hard disk, size 2 inches or Solid State "Removing and installing 2...
  • Page 53 System expansions FUJITSU Workstation CELSIUS W570power+ / W580power+ The FUJITSU Workstation CELSIUS W570power+ / W580power+ is available in two variants: with the installation kit 1 (standard) or the installation kit 2 (optional). The table below therefore also shows the respective installation options for the two installation kits:...
  • Page 54 One hard disk, size 2 Both installation kits "Removing and installing inches or Solid State Disk inch hard disks or Solid State Discs (SSD) (FUJITSU (SSD) Workstation CELSIUS W570 / W570power and W580 / W580power: according to the operable 5...
  • Page 55 Installation kit 1 for up to 2 hard disks, size 3 inches (horizontal), or up to 2 hard disks, size 2 inches (vertical): The hard disks, size 2 inches (vertical), are also installed like the hard disks of installation kit 2 shown in the image below. Fujitsu...
  • Page 56 System expansions Example: Installation kit 2 (optional, with 4 hard disks, maximum upgrade, vertical) Drive cage above: Installation kit 2 (optional) for up to 4 hard disks, size 2 inches (vertical) Fujitsu...
  • Page 57: Removing And Installing Hard Disks In The Lower Part Of The Device (variants: Fujitsu Workstation Celsius W570 / W570power / W580 / W580power)

    System expansions Removing and installing hard disks in the lower part of the device (variants: FUJITSU Workstation CELSIUS W570 / W570power / W580 / W580power) The following sections apply both to 3 inch hard disks and to 2 inch hard disks.
  • Page 58: Removing The Hard Disk Drive

    ► Pull the EasyChange rails off the hard disk drive. ► If you no longer need the EasyChange rails, secure them again at their location in the drive cage. It may be necessary to modify the entry for the drive in the BIOS Setup. Fujitsu...
  • Page 59: Installing A Hard Disk Drive

    ► Connect the cables to the hard disk drive (a). ► Close the casing (see "Closing the casing", Page 36). It may be necessary to modify the entry for the drive in the BIOS Setup. Fujitsu...
  • Page 60: Celsius W570power+, Cold Plug)

    System expansions Removing and installing hard disks in the lower part of the device (variant: FUJITSU Workstation CELSIUS W570power+, cold plug) The following sections apply both to 3 inch hard disks and to 2 inch hard disks. The only difference between 2...
  • Page 61 ► Pull the EasyChange rails off the hard disk drive. ► If you no longer need the EasyChange rails, secure them again at their location in the drive cage. It may be necessary to modify the entry for the drive in the BIOS Setup. Fujitsu...
  • Page 62: Installing A Hard Disk Drive

    (1). Ensure that the connections of the hard disk drive face inwards towards the bottom of the casing. ► Press the levers of the EasyChange rails in the direction of the arrows (2). ► Close the casing (see "Closing the casing", Page 36). Fujitsu...
  • Page 63: Removing And Installing

    W580power+: on the drive frame) The procedure is identical for all three device variants and for both installation kits of the FUJITSU Workstation CELSIUS W570power+ / W580power+ Only the position in the casing is different (see "Overview of the hard disk drives", Page...
  • Page 64: Removing The Hard Disk Drive

    Solid State Disc (SSD)) ► Open the casing (see "Opening the casing", Page 35). ► FUJITSU Workstation CELSIUS W570power+ / W580power+: Open the drive cage (see "Open the drive cage", Page 38) and pull it out of the casing (see "Pull the drive cage out of the casing.", Page...
  • Page 65: Install A Hard Disk, Size 2

    EasyChange rails for the hard disk drive are located on the drive cage. ► Open the casing (see "Opening the casing", Page 35). ► FUJITSU Workstation CELSIUS W570power+ / W580power+: Open the drive cage (see "Open the drive cage", Page 38) and pull it out of the casing (see "Pull the drive cage out of the casing.", Page...
  • Page 66: Removing And Installing

    2 ("Removing and installing 2 inch hard disks in the drive cage (only for the model FUJITSU Desktop CELSIUS W570power+, with both installation kits)", Page 65). Removing the hard disk drive In the cold-plug process, the cables connected at the back of the drive will be disconnected automatically when the EasyChange rails are activated, as described below.
  • Page 67: Installing A Hard Disk Drive

    Installing a hard disk drive In the cold-plug process, the cables in the casing for the drive automatically lock into place when the EasyChange rails are activated, as described below. ► Open the drive cage (see "Open the drive cage", Page 38). Fujitsu...
  • Page 68 ► Press the levers of the EasyChange rails in the direction of the arrow (1). ► Close the drive cage (see "Close the drive cage", Page 41). If necessary, you must adjust the entry for the drive accordingly in the BIOS setup. Fujitsu...
  • Page 69: Removing And Installing 2

    System expansions Removing and installing 2 inch hard disks in the drive cage (only for the model FUJITSU Desktop CELSIUS W570power+, with both installation kits) The procedure for installation kit 1 (for the installation variant with up to two 2...
  • Page 70 (2). Ensure that the connections of the hard disk drive face inwards towards the inside of the casing. ► Close the drive cage (see "Close the drive cage", Page 41). If necessary, you must adjust the entry for the drive accordingly in the BIOS setup. Fujitsu...
  • Page 71: Removing A Hard Disk Drive

    (1), until the levers move upwards and the hard disk is unlocked. ► Press the levers together again (2). ► Pull the hard disk drive out of the drive cage in the direction of the arrow (3). Fujitsu...
  • Page 72 ► If you no longer need the EasyChange rails, secure them again at their location in the drive cage. ► Close the drive cage (see "Close the drive cage", Page 41). If necessary, you must adjust the entry for the drive accordingly in the BIOS setup. Fujitsu...
  • Page 73: Removing And fitting The Front Fan

    ► Remove the front cover from the casing in the direction of the arrow (2). ► Release the detent (3) and slide the fan away from the casing in the direction of the arrow (4).  You can now remove or install the M.2 module or long modules. Fujitsu...
  • Page 74: Installing The Front Fan

    ► Attach the front fan to the centering pins on the housing and move it in the direction of the arrow (1).  The front fan will then be locked in position. ► Fit the front cover onto the casing (2). ► Connect the fan cable to the mainboard. ► Close the casing (see "Closing the casing", Page 36). Fujitsu...
  • Page 75: Installing And Removing A Board

    ► Fold the module lock (a) upwards to open it. ► Loosen the screw on the slot cover (1), if one is fitted. ► Pull the slot cover out of the slot in the direction of the arrow (2). Fujitsu...
  • Page 76 ► Close the casing (see "Closing the casing", Page 36). If you have installed or removed a board, please check the relevant PCI slot settings in the BIOS Setup. If necessary, change the settings. Further information is provided in the PCI board documentation. Fujitsu...
  • Page 77: Removing A Board

    (2). Push the latch to the side to release the card. You can then remove the card as described below. ► Pull the slot cover out of the slot in the direction of the arrow (3). ► Place the board in suitable packaging. Fujitsu...
  • Page 78 "Closing the casing", Page 36). If you have installed or removed a PCI board, please check the relevant PCI slot settings in the BIOS Setup. If necessary, change the settings. Further information is provided in the PCI board documentation. Fujitsu...
  • Page 79: Installing And Removing An M.2 Module

    ► If you have removed the front fan and long component groups: Refit these components (see "Removing and fitting the front fan", Page 69 "Installing a board", Page 71). ► Close the casing (see "Closing the casing", Page 36). If necessary, you must adjust the entry for the drive accordingly in the BIOS Setup. Fujitsu...
  • Page 80: Removing An M.2 Module

    ► If you have removed the front fan and long component groups: Refit these components (see "Removing and fitting the front fan", Page 69 "Installing a board", Page 71). ► Close the casing (see "Closing the casing", Page 36). If necessary, you must adjust the entry for the drive accordingly in the BIOS Setup. Fujitsu...
  • Page 81: Installing And Removing Wlan Antennas

    ► Working in the direction of the arrow (1), place the WLAN antennas onto the plug-in positions of the board (2). ► Secure the WLAN antennas by turning in the direction of the arrow (3). ► Align the WLAN antennas as required. Fujitsu...
  • Page 82: Removing External Wlan Antennas

    ► Open the casing (see "Opening the casing", Page 35). ► FUJITSU Workstation CELSIUS W570+ / W580power+: Open the drive cage (see "Open the drive cage", Page 38) and pull the drive cage out of the casing (see "Pull the drive cage out of the casing.", Page...
  • Page 83: Installing The Heat Sink

    ► Fasten the screws (a). ► Connect the fan leads to the mainboard (FAN CPU). ► FUJITSU Workstation CELSIUS W570+ / W580power+: Insert the drive cage into the casing (see "Slide the drive cage into the housing.", Page...
  • Page 84: Mainboard Expansions

    Upgrading main memory ► Open the casing (see "Opening the casing", Page 35). Mainmemory ► FUJITSU Workstation CELSIUS W570+ / W580power+: Open the drive cage (see "Open the drive cage", Page 38) and pull the drive cage out of the casing (see "Pull the drive cage out of the casing.", Page...
  • Page 85: Replacing The Lithium Battery

    ► Press the catch in the direction of the arrow (1).  The battery jumps out of the holder slightly. ► Remove the battery (2). ► Push the new lithium battery of the identical type into the holder (3) and press it down until it engages. Fujitsu...
  • Page 86: Technical Data

    10 mm / 0,39 in with air vents at least 200 mm / 7,87 in The data sheets of these devices contains further technical data. The data sheets can be found on our website at "http://www.fujitsu.com/fts/". Fujitsu...
  • Page 87: Index

    19 mouse 19 PS/2 keyboard 19 Headphones 17 PS/2 mouse 19 USB keyboard 19 Contents of delivery 13 Important notes 11 Ctrl+Alt+Del 25 Installing, Cursor keys 24 software 20–21 switching on for the first time 20 Data protection 26 Fujitsu...
  • Page 88 Upgrades 80 Safety information 11 Mains adapter Security functions connecting 15 BIOS Setup 28 Microphone jack 17 SmartCard 28 Monitor Security measures 26 switching off 22 Serial port 17, 19 Switching on 22 Connecting devices 19 Monitor port 17 Fujitsu...
  • Page 89 USB port 19 Software, USB port, installing 20–21 connecting devices 20 System expansion 33 connecting keyboard 19 System settings, connecting the mouse 19 BIOS Setup 25 System unit, see Device 12 Workstation 14 Transportation 11–12 Universal Serial Bus 17 Fujitsu...

This manual is also suitable for:

Celsius w570Celsius +w580Celsius w580power

Comments to this Manuals

Symbols: 0
Latest comments: