Positioning The Appliance - Olsberg Virgo Installation Instructions Manual

2.0 INSTALLATION
2.2 - Installation Notes & Guide Cont..
In hermetically insulated rooms a separate air inlet pipe is needed to guarantee a sufficient supply of air
for the operation of the stove. It is also necessary in the case of rooms with forced aeration systems (e/g
extractor fan).
If it is possible a solution must be found for turning off these appliances. Some Olsberg stoves have an
optional connection for an external air inlet. Use of Olsberg stoves in building with hermetic insulation
and mechanical airing systems is only allowed under certain conditions. Authorization of the stove as
"independent of the air in the room" and insulated air inlet from outside are among these conditions. It is
important to consult a competent chimney sweep or expert regarding this matter.
Choose a location for the stove close to the chimney to prevent the use of a long horizontal connecting pipe.
The location of installation has to be flat and level. Make sure that the floor has the necessary load-bearing
capacity. The weight of the appliance can be found on the technical data sheet. In case the load bearing
capacity of the floor is too low, usage of a plate for better load distribution might help. If the problem exists
you should seek professional help.

2.3 - Positioning the Appliance

ęň Ó·˛·ł«ł Ľ·­¬ż˛˝»­ ş®±ł ˝±łľ«­¬·ľ´» ±® ¸»ż¬ ­»˛­·¬·Ş»
The technical data sheet and the type of board on the stove contain the data referring to the stove that
łż¬»®·ż´­ć
might differ from these standard regulations.
̸» ¬»˝¸˛·˝ż´ Ľż¬ż ­¸»»¬ ż˛Ľ ¬¸» ¬§°» ľ±ż®Ľ ±˛ ¬¸» ­¬±Ş» ˝±˛¬ż·˛ ¬¸» Ľż¬ż ®»ş»®ó
In case of combustible floors, being sensitive to a rise in temperature, non combustible floor protectors
®·˛ą ¬± ¬¸» ­¬±Ş» ¬¸ż¬ ł·ą¸¬ Ľ·şş»® ş®±ł ¬¸»­» ­¬ż˛Ľż®Ľ ®»ą«´ż¬·±˛­ň
must be used. This floor protector must reach 50cm beyond the front of the stove, 30cm to either side
ײ ˝ż­» ±ş ˝±łľ«­¬·ľ´» ş´±±®­ô ľ»·˛ą ­»˛­·¬·Ş» ¬± ż ®·­» ·˛ ¬»ł°»®ż¬«®»ô ˛±˛ó˝±łó
(measured form inside the combustion chamber). The floor protector can be made of metal or glass. The
ľ«­¬·ľ´» ş´±±® °®±¬»˝¬±® ł«­¬ ľ» «­»Ľň ̸·­ ş´±±® °®±¬»˝¬±® ł«­¬ ®»ż˝¸ ë𠽳
given minimum distances from combustible or heat sensitive materials have to be kept by all means at the
ľ»§±˛Ľ ¬¸» ş®±˛¬ řş®±ł ¬¸» ˝¸ż®˝±ż´ °ż˛÷ô í𠽳 ľ»§±˛Ľ ¬¸» ­·Ľ» řş®±ł ¬¸» ·˛˛»®
back, the front and sides.
©ż´´ ±ş ¬¸» ˝±łľ«­¬·±˛ ˝¸żłľ»®÷ ±ş ¬¸» ş·®»°´ż˝»ň ̸» ş´±±® °®±¬»˝¬±® ˝ż˛ ľ»
łżĽ» ±ş ł»¬ż´ ±® ą´ż­­ ©¸·˝¸ ˝ż˛ ľ» ˝¸±­»˛ ş®±ł ¬¸» °®±Ľ«˝¬ ´·­¬ ±ş Ú×ÎŰó
Certain stoves can be installed without safety distances, which can be found on the technical data sheet
ĐÔßÝŰ ż˝˝»­­±®·»­ň
and the type of board.
̸» ą·Ş»˛ ł·˛·ł«ł ­żş»¬§ Ľ·­¬ż˛˝»­ ş®±ł ˝±łľ«­¬·ľ´» ±® ¸»ż¬ ­»˛­·¬·Ş» łż¬»ó
®·ż´­ ¸żŞ» ¬± ľ» µ»°¬ ľ§ ż´´ ł»ż˛­ ż¬ ¬¸» ľż˝µô ¬¸» ş®±˛¬ ż˛Ľ ­·Ľ»©ż§­ň
More information regarding min. safety distances from the connecting pipe can be found at the description
of the connection.
ײ ˝ż­» ż ş·®»°´ż˝» ­¬±Ş» ˝ż˛ ľ» ·˛­¬ż´´»Ľ ©·¬¸±«¬ ­żş»¬§ Ľ·­¬ż˛˝»­ ¬¸ż¬ ˝ż˛ ľ»
ş±«˛Ľ ±˛ ¬¸» ¬»˝¸˛·˝ż´ Ľż¬ż ­¸»»¬ ż˛Ľ ¬¸» ¬§°» ľ±ż®Ľň
Ó±®» ·˛ş±®łż¬·±˛ żľ±«¬ ­żş»¬§ Ľ·­¬ż˛˝»­ ş®±ł ¬¸» ˝±˛˛»˝¬·˛ą °·°» ˝ż˛ ľ» ş±«˛Ľ
ż¬ ¬¸» Ľ»­˝®·°¬·±˛ ±ş ˝±˛˛»˝¬·˛ąň
î𠽳
î𠽳
í𠽳
ë𠽳
ďđ𠽳
PAGE 9
î𠽳
ë𠽳