Table of Contents
Advertisement
C. Quick Programming Features
Description
First emergency speed dial number
Second emergency speed dial number
Third emergency speed dial number
Fourth emergency speed dial number
Fifth emergency speed dial number
Central station receiver number
Central station voice number
Transmit ID number on inbound calls: 0 = Disable (factory setting), 1 = Enable
Speaker Mode: 0 = OFF/Silent Monitor (factory setting), 1 = OFF until answered, 2 = ON
Voice announcer/miscellaneous options (factory set to 001210)
Timing/Dialing options (factory set to 234721)
Security code (factory set to 845464)
Identification number (factory cleared)
Second central station identification number (factory cleared)
Access Code
To add a Q at any point in the dialing string
To add a # at any point in the dialing string
To add a four second pause at any point in the dialing string
To clear any speed dial number
Diagnostic tones (used to check mic and speaker operation)
Exit programming and disconnect
Reset all programming to factory default settings
Note: A double beep indicates a valid memory position, four beeps indicate an error.
D. Speed Dial Numbers
Note: Up to 20 digits can be stored in each dial position. Special features such as pause, mode change, touch tone
1. Emergency Speed Dial Numbers
The emergency speed dial number programmed in location #00 is the number that is dialed
when the "PANIC" button is first pressed. Additional speed dial numbers will be dialed when
there is no answer or a busy signal is detected and the next number redial features are
activated. To program, enter the desired speed dial number followed by the location number
(#00 - #04). To clear a speed dial location, simply enter the memory location (#00 - #04) alone.
The PB-3 phone is factory set with no speed dial number programmed.
2. Speed Dial Programming Examples
To Program the PB-3 Phone...
...to store 555-1234 as the first emergency speed dial
number
...to store a touch tone 9, a four second pause, and
then 333-4444 into the second emergency speed dial
memory position
...to clear the first emergency speed dial number
E. Transmit ID Number on Inbound Calls
With this feature enabled (1#15) the PB-3 will automatically transmit the DTMF ID number on all inbound calls.
Transmission speed is 50msec on/off. If a # is entered within 5 seconds of the ID transmission this will force the unit to
hang up. Factory Setting: Disabled, 0#15
(memory locations #00 - #04)
Access Programming (see page 3) Enter digits: 5 5 5 1 2 3 4 # 0 0
Access Programming (see page 3)
Access Programming (see page 3)
(memory location #15)
4
Enter Digits
0-20 digits
0-20 digits
0-20 digits
0-20 digits
0-20 digits
0-20 digits
0-20 digits
0 or 1
0,1 or 2
6 digits
6 digits
6 digits
0-20 digits
0-20 digits
0-6 digits
QQ
#
Q
7
Q
(no digits)
0
Q
#7
###
4 second pause
Step 1
9 Q7 3 3 3 4 4 4 4 # 0 1
Memory
+
Location
then
#00
then
#01
then
#02
then
#03
then
#04
then
#05
then
#06
then
#15
then
#16
then
#17
then
#18
then
#19
then
#20
then
#21
then
#23
then
#00 - #09
and # count as single digits.
Q
To Program:
Enter:
Q
QQ
#
Q#
Q7
0, 1, 2 .... 9
0, 1, 2 .... 9
Step 2
Enter digits:
Enter digits: # 0 0
Advertisement
Table of Contents
