Speed Dial Numbers; Identification Number - Viking E-1600-03B Manual

C. Quick Programming Features
First emergency speed dial number .........................................................................
Second emergency speed dial number ...................................................................
Third emergency speed dial number .......................................................................
Fourth emergency speed dial number .....................................................................
Fifth emergency speed dial number .........................................................................
Central station receiver number ...............................................................................
Central station voice number ...................................................................................
First "Info" speed dial number (E-1600-20A and E-1600-52A only) .........................
Second "Info" speed dial number (E-1600-20A and E-1600-52A only) ....................
Third "Info" speed dial number (E-1600-20A and E-1600-52A only) ........................
Voice announcer/miscellaneous options (factory set to 001210) .............................
Timing/Dialing options (factory set to 234721) .........................................................
Security code (factory set to 845464) ......................................................................
Identification number (factory cleared) ....................................................................
Second central station identification number (factory cleared) .................................
Q
To add a at any point in the dialing string ..............................................................
To add a # at any point in the dialing string ..............................................................
To add a four second pause at any point in the dialing string ...................................
To clear any speed dial number ...............................................................................
Diagnostic tones (used to check mic and speaker operation) ..................................
Exit programming and disconnect ...........................................................................
Reset all programming to factory default settings ....................................................
Note: A double beep indicates a valid memory position, four beeps indicate an error.
D. Speed Dial Numbers
Note: Up to 20 digits can be stored in each dial position. Special features such as pause, mode change, touch tone Q and # count
as single digits.
1. Emergency Speed Dial Numbers
The emergency speed dial number programmed in location #00 is the number that is dialed
when the "HELP" / "CALL" button is first pressed. Additional speed dial numbers will be
dialed when there is no answer or a busy signal is detected and the next number redial fea-
tures are activated. To program, enter the desired speed dial number followed by the location
number (#00 - #04). To clear a speed dial location, simply enter the memory location (#00 -
#04) alone. The 1600A series phone is factory set with no speed dial number programmed.
2. "INFO" Speed Dial Numbers
The information speed dial number programmed in location #07 is the telephone or extension number that is dialed when the
"INFO" button is first pressed. Additional information speed dial numbers will be dialed when there is no answer and the next
number redial feature is activated. The E-1600-20A phone will cycle through the programmed speed dial numbers until
answered. To program, enter the desired speed dial number followed by the location number (#07 - #09). To clear a speed dial
location, simply enter the location (#07 - #09) alone.
3. Speed Dial Programming Examples
To Program the 1600A Series Phone...
...to store 555-1234 as the first emergency speed dial number
...to store a Touch Tone 9, a four second pause and then 333-4444
into the second "Info" speed dial memory position
...to clear the first emergency speed dial number
E. Identification Number
The Touch Tone I.D. number (up to 20 digits) is used by emergency personnel to identify the location of the caller and is given out
when the receiving party presses a Touch Tone Q. The security office can display the number using a Touch Tone decoder. To pro-
gram the I.D. number, enter the desired number followed by #20. Example: To store 333 as the I.D. number, enter: 3 3 3 # 2 0
(memory locations #00 - #04)
(E-1600-20A/52A Only) (memory locations #07 - #09)
(memory location #20)
Enter Digits - then - Enter Memory Location
0-20 digits then
0-20 digits then
0-20 digits then
0-20 digits then
0-20 digits
then
0-20 digits then
0-20 digits then
0-20 digits then
0-20 digits
then
0-20 digits then
6 digits then
6 digits then
6 digits then
0-20 digits
then
0-20 digits then
QQ
Q
#
Q
7
(no digits) then
Q
0
#7
###
To Program:
4 second pause
Step 1 -
Step 2 - Enter Digits:
See Section A
Enter Programming
Enter Programming 9
Enter Programming
Enter:
Q QQ
Q
# #
Q
7
0, 1, 2...9 0, 1, 2...9
5 5 5 1 2 3 4 # 0 0
Q
7 3 3 3 4 4 4 4 # 0 8
# 0 0
7