EarthWay 2600A-Plus Estate Assembly And Operating Instructions Manual
Broadcast spreader
Hide thumbs
Also See for 2600A-Plus Estate:
- Assembly instructions manual (10 pages) ,
- Assembly and operating instructions (5 pages) ,
- Assembly instructions manual (6 pages)
Table of Contents
Advertisement
2600A-Plus Estate
Broadcast Spreader
ASSEMBLY and OPERATING INSTRUCTIONS
IF YOU ARE MISSING ANY PARTS, HAVE ANY DIFFICULTY IN ASSEMBLY, OR HAVE ANY QUESTIONS REGARDING
THE SAFE OPERATION OF THIS SPREADER, PLEASE CONTACT US. THIS MODEL INCLUDES LIFETIME TECHNICAL
SUPPORT HOT LINE: 574-848-7491 or 800-294-0671, email: techsupport@earthway.com
HELPFUL HINTS:
; Make sure the ARROW on the gear box points to the front of the spreader. The impeller must turn clockwise.
Reversing the gearbox will cause the impeller to turn counter clockwise. Clean the impeller plate after each
use. Fertilizer stuck on the impeller blades will cause uneven spreading.
; Your spreader is designed to be pushed at three miles per hour, which is a brisk walking speed. Slower or
faster speeds will change the spread patterns. Wet fertilizer will also change the spread pattern and flow rate.
Clean and dry your spreader thoroughly after each use. A coating of light spray oil on all metal parts will help
prevent corrosion, pay special attention to coating the inside of the steel tubing.
; Gears are permanently lubricated at the factory. Do not open the gearbox or dirt may enter.
1. Remove and identify all loose parts from carton.
Upper handles
Handle Shaft
Wheels
Impeller
3. Install gear box by inserting the pinion shaft into hole in center
of hoppers bottom. The ARROW on the gearbox must point to
FRONT of the hopper. Follow label instructions on hopper.
Remove agitator when
using Rock Salt to prevent
gearbox damage
REVIEW THE DIRECTIONS BEFORE ASSEMBLY
Gauge &
Linkage
Assembly
Control Rod
Frame
Gearbox
Lower
Handles
Axle
Warning
2. Position hopper as shown to the
right. Install Frame using (4) #10
x 1¼" Flat Head Phillips screws.
TIGHTEN THESE NOW
Arrow
#10 X 1-1/4"
Flat Head Screw
8-2016 Pt# 52215
PAGE 1
Advertisement
Table of Contents
Related Manuals for EarthWay 2600A-Plus Estate
Summary of Contents for EarthWay 2600A-Plus Estate
- Page 1 IF YOU ARE MISSING ANY PARTS, HAVE ANY DIFFICULTY IN ASSEMBLY, OR HAVE ANY QUESTIONS REGARDING THE SAFE OPERATION OF THIS SPREADER, PLEASE CONTACT US. THIS MODEL INCLUDES LIFETIME TECHNICAL SUPPORT HOT LINE: 574-848-7491 or 800-294-0671, email: techsupport@earthway.com HELPFUL HINTS: REVIEW THE DIRECTIONS BEFORE ASSEMBLY ;...
- Page 2 4. Install lower handles onto Frame and secure with ¼-20 x 2¼” Slide Axle through as shown bolt through hole in Frame Braces and through the hole in frame install locknut. Next, Slide the axle (Coast Wheel side first) through the right side lower handle and into the gearbox (with the arrow facing the FRONT), you will need to rotate the axle to engage Right...
- Page 3 10. Attach Linkage Pivot with 1/4-20 x 1½” Hex Bolt, Flat Washer, Spacer and Locknut as shown below. Next, install Control Rod into the Shut-Off Plate as shown at the right. TIP: Make sure that the Control 12317 Rod is above the Lower Handles. Shut-Off Plate Control Lever...
-
Page 4: Operating Instructions
5-Years to the end user with the original purchase receipt. If a manufacturing non-conformance is found, Earthway Products, Inc. at its discretion will repair or replace the part(s) or product at no charge provided the failure is not the result of incorrect installation, mishandling, misuse, tampering, or normal wear and tear as determined by Earthway. - Page 5 Earthway Products, Inc. P.O. Box 547 Bristol, IN 46507 Phone: 574-848-7491 or 800-294-0671 77000 OPTIONAL www.earthway.com Heavy-Duty Rain Cover 1” 1-1/2” 2” 2-1/4” 2-3/4” Coast Wheel Drive Wheel Warning Remove agitator when using Rock Salt to prevent gearbox damage 2600APlus Broadcast Spreader...
- Page 6 Broadcast Setting Matrix Calibration Techniques How to ensure your spreader is properly calibrated Make sure the drop holes in the bottom of the hopper are fully open when the Rate Control handle is on #30. If not, please adjust the control rod to allow for a full open hopper position at #30. Drop holes shown fully open.
- Page 7 Manufacturer makes no warranty as to the uniformity of coverage actually obtained from the settings listed. 25 Grams 5 LBS. SPREAD PATH FULL Rate HALF Rate (one pass) (two passes) SIDEWALK DRIVEWAY FLOWER FLOWER Pt. #53192 © 2015 Earthway Products, Inc. All rights reserved...