Carrier AERO 39MN Installation, Start-Up And Service Instructions Manual page 97

GROUP NUMBER PARAMETER NUMBER
99
10
11
12
13
14
16
20
21
22
26
30
31
34
40
*Factory Programmed as follows: For 208-230v / 60 Hz = 208, 460v / 60 Hz = 460, 200-230v / 50 Hz = 200, 380 / 50 Hz = 400.
†Motor Nameplate Amps. Factory programmed per Programmed Settings in Table 28. This value should always be compared to the actual motor nameplate value
before start-up.
**Maximum Output Amps — Factory programmed per Table 28.
Table 29 — Air Handler VFD Factory-Set Parameters
DESCRIPTION
9902 Application Macro
9904 Motor Control Mode
9905 Motor Nominal Voltage
9906 Motor Nominal Current
9907 Motor Nominal Frequency
9908 Motor Nominal Speed
9909 Motor Nominal Power
1001 EXT1 Commands
1002 EXT2 Commands
1003
1104 REF1 Minimum
1105 REF1 Maximum
1201 Constant Speed Select
1202 Constant Speed Value
1301 Minimum AI-1
1302 Maximum AI-1
1303
1304 Minimum AI-2
1305 Maximum AI-2
1306
1401 Relay Output 1
1402 Relay Output 2
1403 Relay Output 3
1601
1608 Start Enable 1
1609 Start Enable 2
2002 Maximum Fan Speed
2003 Maximum Current
2007 Minimum Frequency
2008 Maximum Frequency
2101 Start Function
2102 Stop Function
2202 Accelerate Time
2203 Decelerate Time
2605 Volt/Freq Ratio
2606 Switching Frequency
2607 Switching Frequency Control
3006 Motor Thermal Time
3007 Motor Load Curve
3008 Zero Speed Load
3009 Break Point Frequency
3010 Stall Function
3011 Stall Frequency
3012
3017
3101 Number of Retries
3102
3103
3104 AR Overcurrent
3105 AR Overvoltage
3106 AR Undervoltage
3107 AR AI< Minimum
3108 AR External Fault
3415 Signal Parameter 3
3416 Signal 3 Minimum
3417 Signal 3 Maximum
3418 Output 3 DSP Form
3419 Output 3 DSP units
3420 Output 3 Minimum
3421 Output 3 Maximum
4001
4002 Integration Time
4005 Error Value Invert
4006
4007 Display Format
4010 Setpoint Select
4011 Internal Setpoint
4012 Setpoint Minimum
4013 Setpoint Maximum
4016
4027 PID 1 Parameter Set
Direction
Filter AI-1
Filter AI-2
Run Enable
Stall Time
Earth Fault
Trial Time
Delay Time
Gain
Units
ACT 1 Input
96
VALUE
Supply Fan
Scalar
*
†
60 Hz or 50 Hz
Nameplate rpm at Load
Nameplate Hp
DI-1 Start / Stop
(0) N/A
Forward
9.33 Hz at 60 Hz / 7.78 Hz at 50 Hz
62.7 Hz at 60 Hz / 52.2 Hz at 50 Hz
DI-3
Field Program (8 Hz – Motor Nominal Freq.)
0%
100%
1 sec
0%
100%
1 sec
Started
Run
Fault (Inverted)
DI-2
DI-4
DI-5
Per Fan
**
8 Hz
Belt Drive: 60 Hz/50 Hz
Direct Drive: Calculated Per Fan and Motor
FlyStart
Coast
60 Seconds
60 Seconds
Linear
8 KHz
ON
1050
105%
70%
35 Hz
Fault
20 Hz
20 sec
Fault
2
600 sec
5 sec
Enable
Enable
Enable
Disable
(0) Disable
SPEED
0
30000
0
rpm
0
30000
0.7
30 sec
NO
Volts
x.xxx
Internal
Field Program (0.0 v – 10.0 v)
0.0 v
10.0 v
AI-2
SET 1