Honda F300 Owner's Manual
  1. Manuals
  2. Brands
  3. Honda Manuals
  4. Tiller
  5. F300
  6. Owner's manual

Honda F300 Owner's Manual

Hide thumbs Also See for F300:
Table of Contents

Advertisement

Quick Links

See also: Owners Workshop Manual
4MV488000.book -1 ページ ２０１６年３月２日　水曜日　午後１２時３６分
Honda F300
OWNER'S MANUAL
취급 설명서
使用說明書

Advertisement

Table of Contents
loading

Related Manuals for Honda F300

Summary of Contents for Honda F300

  • Page 1 4MV488000.book -1 ページ ２０１６年３月２日　水曜日　午後１２時３６分 Honda F300 OWNER’S MANUAL 취급 설명서 使用說明書...
  • Page 2 The information and specifications included in this publication were in effect at the time of approval for printing. Honda Motor Co., Ltd. reserves the right, however, to discontinue or change specifications or design at any time without notice and without incurring any obligation whatsoever.
  • Page 3 4MV488000.book 1 ページ ２０１６年３月２日　水曜日　午後１２時３６分 INTRODUCTION Congratulations on your selection of a Honda tiller. We are certain you will be pleased with your purchase of one of the finest tillers on the market. We want to help you get the best results from your new tiller and to operate it safely.
  • Page 4 4MV488000.book 2 ページ ２０１６年３月２日　水曜日　午後１２時３６分 INTRODUCTION A FEW WORDS ABOUT SAFETY Your safety and the safety of others are very important. And using this tiller safely is an important responsibility. To help you make informed decisions about safety, we have provided operating procedures and other information on labels and in this manual.

  • Page 5: Table Of Contents

    4MV488000.book 3 ページ ２０１６年３月２日　水曜日　午後１２時３６分 CONTENTS TILLER SAFETY..................5 IMPORTANT SAFETY INFORMATION ..........5 SAFETY LABEL LOCATIONS..............8 CONTROLS ....................10 COMPONENT & CONTROL LOCATIONS...........10 CONTROLS...................11 Fuel Valve ..................11 Choke Lever..................11 Engine Switch ..................11 Starter Grip..................12 Throttle Lever ...................12 Clutch Lever..................13 Drag Bar....................13 BEFORE OPERATION ................14 ARE YOU READY TO GET STARTED?..........14 IS YOUR TILLER READY TO GO? ............14 Check the Engine ................15...
  • Page 6 4MV488000.book 4 ページ ２０１６年３月２日　水曜日　午後１２時３６分 CONTENTS SERVICING YOUR TILLER (continued) ENGINE OIL CHANGE................33 ENGINE OIL RECOMMENDATIONS ...........34 TRANSMISSION OIL LEVEL CHECK...........35 AIR FILTER INSPECTION ..............36 AIR FILTER CLEANING ................36 SPARK PLUG SERVICE................39 THROTTLE CABLE ADJUSTMENT .............41 TINES AND FASTENERS CHECK............42 TINE REPLACEMENT................43 RECOIL STARTER COVER CHECK AND CLEANING......45 STORAGE....................46 STORAGE PREPARATION..............46...

  • Page 7: Tiller Safety

    4MV488000.book 5 ページ ２０１６年３月２日　水曜日　午後１２時３６分 TILLER SAFETY IMPORTANT SAFETY INFORMATION Honda tillers are designed to cultivate earth outdoors. Other uses can result in injury to the operator or damage to the tiller and other property. Most injuries or property damage can be prevented if you follow all the instructions in this manual and on the tiller.
  • Page 8 4MV488000.book 6 ページ ２０１６年３月２日　水曜日　午後１２時３６分 TILLER SAFETY Fire and Burn Hazards • The exhaust system gets hot enough to ignite some materials. – Keep the tiller at least 1 meter away from buildings and other equipment during operation. – Keep flammable materials away from the tiller. •...
  • Page 9 4MV488000.book 7 ページ ２０１６年３月２日　水曜日　午後１２時３６分 TILLER SAFETY Keep Shields in Place Guards and shields are designed to protect you from being hit by thrown objects and to keep you from touching hot engine parts and moving components. For your safety and the safety of others, keep all shields in place when the engine is running.

  • Page 10: Safety Label Locations

    SAFETY LABEL LOCATIONS These labels warn you of potential hazards that can cause serious injury. Read them carefully. If a label comes off or becomes hard to read, contact your Honda servicing dealer for a replacement. For RD, IN, T types...
  • Page 11 4MV488000.book 9 ページ ２０１６年３月２日　水曜日　午後１２時３６分 TILLER SAFETY For KW types...

  • Page 12: Controls

    4MV488000.book 10 ページ ２０１６年３月２日　水曜日　午後１２時３６分 CONTROLS COMPONENT & CONTROL LOCATIONS SPARK PLUG THROTTLE LEVER ENGINE SWITCH FUEL VALVE CLUTCH LEVER HANDLE GRIP CHOKE LEVER STARTER GRIP DRAG BAR TRANSMISSION OIL FILLER CAP AIR CLEANER FUEL TANK CAP MUFFLER BELT COVER ENGINE OIL FILLER CAP For KW types ENGINE OIL DRAIN BOLT FRONT GUARD...

  • Page 13: Controls

    4MV488000.book 11 ページ ２０１６年３月２日　水曜日　午後１２時３６分 CONTROLS CONTROLS Fuel Valve The fuel valve opens and closes the connection between the fuel tank and the carburetor. The fuel valve must be in the ON position for the engine to run. FUEL VALVE After stopping the engine, turn the fuel valve to the OFF position.

  • Page 14: Starter Grip

    4MV488000.book 12 ページ ２０１６年３月２日　水曜日　午後１２時３６分 CONTROLS Starter Grip STARTER GRIP Pulling the starter grip operates the recoil starter to crank the engine for starting. Throttle Lever The throttle lever controls engine THROTTLE LEVER speed. Moving the throttle lever in the directions shown makes the engine run faster or slower.

  • Page 15: Clutch Lever

    4MV488000.book 13 ページ ２０１６年３月２日　水曜日　午後１２時３６分 CONTROLS Clutch Lever The clutch lever engages and disengages the transmission ENGAGED that drives the tines. DISENGAGED CLUTCH LEVER Drag Bar The drag bar controls tilling depth and should always be used when tilling. It enables you to compensate for the RETAINER hardness of the soil.

  • Page 16: Before Operation

    4MV488000.book 14 ページ ２０１６年３月２日　水曜日　午後１２時３６分 BEFORE OPERATION ARE YOU READY TO GET STARTED? Your safety is your responsibility. A little time spent in preparation will significantly reduce your risk of injury. Knowledge Read and understand this manual. Know what the controls do and how to operate them.

  • Page 17: Check The Engine

    • Start the engine. Check for abnormal sounds. (See pages 17 through 18 for starting procedure.) • Check that the engine stops securely by operating the engine switch. (See page 25 for stopping procedure.) • If you notice any other abnormal symptoms, consult with your authorized Honda dealer promptly.

  • Page 18: Operation

    4MV488000.book 16 ページ ２０１６年３月２日　水曜日　午後１２時３６分 OPERATION SAFE OPERATING PRECAUTIONS Before operating the tiller for the first time, please review both the TILLER SAFETY chapter (see page 5) and the chapter titled BEFORE OPERATION (see page 14). For your safety, do not start or operate the tiller in an enclosed area such as a garage.

  • Page 19: Starting The Engine

    4MV488000.book 17 ページ ２０１６年３月２日　水曜日　午後１２時３６分 OPERATION STARTING THE ENGINE Refer to Safe Operating Precautions on page 16. 1. Turn the fuel valve to the ON position. FUEL VALVE 2. Move the choke lever to the CLOSED position to start a cold engine.
  • Page 20 4MV488000.book 18 ページ ２０１６年３月２日　水曜日　午後１２時３６分 OPERATION 4. Move the throttle lever away from the SLOW position, about 1/3 of the way toward the FAST position. THROTTLE LEVER SLOW 5. Pull the starter grip lightly until STARTER GRIP you feel resistance, and then pull briskly in the direction of the arrow as shown.

  • Page 21: Operating The Controls For Tilling

    4MV488000.book 19 ページ ２０１６年３月２日　水曜日　午後１２時３６分 OPERATION OPERATING THE CONTROLS FOR TILLING If the tines dig in but the machine will not move forward, move the handlebars from side-to-side. When turning, push down on the handlebars to bring the tiller’s weight to the rear; this will make turning easier.
  • Page 22 4MV488000.book 20 ページ ２０１６年３月２日　水曜日　午後１２時３６分 OPERATION Tilling Depth Adjustment The drag bar is used to control the tilling depth, which can be adjusted by removing the pin and RETAINER retainer and sliding the drag bar up and down as necessary. During operation, if the machine jerks forward while tilling, press DRAG BAR down on the handlebars.
  • Page 23 4MV488000.book 21 ページ ２０１６年３月２日　水曜日　午後１２時３６分 OPERATION Rotor Removal Wear heavy gloves to protect your hands. When removing the rotor park the tiller on level ground, stop the engine and disconnect the spark plug cap from the spark plug. Turn the fuel valve lever to the OFF position. 1.
  • Page 24 4MV488000.book 22 ページ ２０１６年３月２日　水曜日　午後１２時３６分 OPERATION 3. Grip the handlebar and push it in the direction of the arrow to lift the nearest rotor off the ground. Keep this condition. Do not pull the cables while gripping the handlebar. Pay attention, when tilting the tiller. The gasoline may leak if the tilting angle is more than necessary.
  • Page 25 4MV488000.book 23 ページ ２０１６年３月２日　水曜日　午後１２時３６分 OPERATION Rotor Installation Pay attention, when tilting the tiller. The gasoline may leak if the tilting angle is more than necessary. 1. Install the main rotor to the axle. Insert the retainer (7 x 75 mm) and set the lock pin so that the ring of the lock pin is in the direction of rotation.

  • Page 26: Handling Tips

    4MV488000.book 24 ページ ２０１６年３月２日　水曜日　午後１２時３６分 OPERATION HANDLING TIPS • Adjust the handlebar height to a comfortable position (waist height for normal tilling). • The drag bar should always be used when tilling. It enables you to compensate for the hardness of the soil. The ideal height of the drag bar will depend on the type of soil being tilled and soil conditions at the time of tilling.

  • Page 27: Stopping The Engine

    4MV488000.book 25 ページ ２０１６年３月２日　水曜日　午後１２時３６分 OPERATION STOPPING THE ENGINE To stop the engine in an emergency, simply turn the engine switch to the OFF position. Under normal conditions, use the following procedure. 1. Release the clutch lever to the DISENGAGED position. ENGAGED DISENGAGED CLUTCH LEVER...

  • Page 28: Servicing Your Tiller

    Remember that an authorized Honda servicing dealer knows your tiller best and is fully equipped to maintain and repair it. To ensure the best quality and reliability, use only new, Honda Genuine parts or their equivalents for repair and replacement.

  • Page 29: Maintenance Safety

    4MV488000.book 27 ページ ２０１６年３月２日　水曜日　午後１２時３６分 SERVICING YOUR TILLER MAINTENANCE SAFETY Some of the most important safety precautions follow. However, we cannot warn you of every conceivable hazard that can arise in performing maintenance. Only you can decide whether or not you should perform a given task. Improper maintenance can cause an unsafe condition.

  • Page 30: Maintenance Schedule

    (2) Service every 10 operating hours or every day when used in dusty areas. (3) These items should be serviced by your Honda servicing dealer, unless you have the proper tools and are mechanically proficient. Refer to the Honda shop manual for service procedures.

  • Page 31: Refueling

    4MV488000.book 29 ページ ２０１６年３月２日　水曜日　午後１２時３６分 SERVICING YOUR TILLER REFUELING Park on level ground, stop the engine, put proper mounting under the front frame and put wood block under the drag bar as shown, to keep the tiller horizontal. Remove the fuel tank cap and check the fuel level. Refill the tank if the fuel level is low.
  • Page 32 4MV488000.book 30 ページ ２０１６年３月２日　水曜日　午後１２時３６分 SERVICING YOUR TILLER Gasoline is highly flammable and explosive. You can be burned or seriously injured when handling fuel. • Stop the engine and keep heat, sparks, and flame away when refueling. • Handle fuel only outdoors. •...

  • Page 33: Fuel Recommendations

    4MV488000.book 31 ページ ２０１６年３月２日　水曜日　午後１２時３６分 SERVICING YOUR TILLER FUEL RECOMMENDATIONS This engine is certified to operate on unleaded gasoline with a research octane rating of 91 or higher (a Pump Octane Number of 86 or higher). You may use regular unleaded gasoline containing no more than 10% ethanol (E10) or 5% methanol by volume.

  • Page 34: Engine Oil Level Check

    4MV488000.book 32 ページ ２０１６年３月２日　水曜日　午後１２時３６分 SERVICING YOUR TILLER ENGINE OIL LEVEL CHECK Check the engine oil level with the tiller on a level surface (see page 29) and the engine stopped. 1. Remove the engine oil filler cap. 2. Check the oil level. 3.

  • Page 35: Servicing Your Tiller (Continued)

    4MV488000.book 33 ページ ２０１６年３月２日　水曜日　午後１２時３６分 SERVICING YOUR TILLER ENGINE OIL CHANGE Drain the oil while the engine is warm to assure rapid and complete draining. 1. Pull up the handlebar while holding it to contact the front end of the tiller to the ground. 2.

  • Page 36: Engine Oil Recommendations

    AMBIENT TEMPERATURE The SAE oil viscosity and service category are in the API label on the oil container. Honda recommends that you use API SERVICE category SE or later (or equivalent) oil. Running the engine with wrong type/grade of Oil is misuse and can cause engine damage.

  • Page 37: Transmission Oil Level Check

    4MV488000.book 35 ページ ２０１６年３月２日　水曜日　午後１２時３６分 SERVICING YOUR TILLER TRANSMISSION OIL LEVEL CHECK Check the transmission oil level with the tiller on a level surface (see page 29) and the engine stopped. Make sure the area around the oil level check bolt and the oil filler cap is clean. 1.

  • Page 38: Air Filter Inspection

    4MV488000.book 36 ページ ２０１６年３月２日　水曜日　午後１２時３６分 SERVICING YOUR TILLER AIR FILTER INSPECTION AIR CLEANER COVER WING NUT 1. Unscrew the wing nut, and remove the air cleaner cover. Check the air filter elements to be sure they are clean and in good condition. GROMMET PAPER 2.
  • Page 39 4MV488000.book 37 ページ ２０１６年３月２日　水曜日　午後１２時３６分 SERVICING YOUR TILLER 4. Remove the elbow packing and clean it if it is to be reused. 5. Separate the air filter elements, carefully check them for holes or tears and replace if necessary. 6. Clean both filter elements if they are to be reused. Foam element: Clean in warm soapy water, rinse and allow to dry thoroughly, or clean with a high flash point solvent and allow to dry.
  • Page 40 4MV488000.book 38 ページ ２０１６年３月２日　水曜日　午後１２時３６分 SERVICING YOUR TILLER AIR CLEANER COVER 8. Wipe dirt from the inside of the WING NUT air cleaner cover using a moist rag. 9. Set the elbow packing and air GROMMET cleaner under cover on the air PAPER cleaner elbow.

  • Page 41: Spark Plug Service

    4MV488000.book 39 ページ ２０１６年３月２日　水曜日　午後１２時３６分 SERVICING YOUR TILLER SPARK PLUG SERVICE Recommended spark plug: C4HSB (NGK) An incorrect spark plug can cause engine damage. 1. Disconnect the spark plug cap, and remove any dirt from around the spark plug area. 2. Remove the spark plug with the spark plug wrench. SPARK PLUG WRENCH 3.
  • Page 42 4MV488000.book 40 ページ ２０１６年３月２日　水曜日　午後１２時３６分 SERVICING YOUR TILLER If reinstalling a used spark plug, tighten 1/8 – 1/4 turn after the spark plug seats. If installing a new spark plug, tighten 1/2 turn after the spark plug seats. TORQUE: 12 N∙m A loose spark plug can overheat and damage the engine.

  • Page 43: Throttle Cable Adjustment

    4MV488000.book 41 ページ ２０１６年３月２日　水曜日　午後１２時３６分 SERVICING YOUR TILLER THROTTLE CABLE ADJUSTMENT Measure the free play at the lever tip. Free play: 5.0 – 10.0 mm If the free play is incorrect, loosen the lock nut and turn the adjusting nut in or out as required. After adjustment, tighten the lock nut.

  • Page 44: Tines And Fasteners Check

    4MV488000.book 42 ページ ２０１６年３月２日　水曜日　午後１２時３６分 SERVICING YOUR TILLER TINES AND FASTENERS CHECK Use Honda Genuine replacement tines or their equivalent. Wear heavy gloves to protect your hands. 1. Check for damage, bent, or loose tines. If abnormality is found, tighten or replace the damaged part (see page 43).

  • Page 45: Tine Replacement

    SERVICING YOUR TILLER TINE REPLACEMENT Remove the rotor from the axle before replacing the tine (see page 21). Use Honda Genuine replacement tines or their equivalent. Wear heavy gloves to protect your hands. Install the tines properly. Incorrect arrangement of the tines or installing the tines in the wrong direction will cause vibration and hinder proper tilling.
  • Page 46 4MV488000.book 44 ページ ２０１６年３月２日　水曜日　午後１２時３６分 SERVICING YOUR TILLER Tine positions Right side Left side 1. Install two B tines 1. Install two A tines pointing out so that the pointing out so that the direction of the tines is direction of the tines is as the same as the hole that same as the hole that is is on the rotor shaft.

  • Page 47: Recoil Starter Cover Check And Cleaning

    4MV488000.book 45 ページ ２０１６年３月２日　水曜日　午後１２時３６分 SERVICING YOUR TILLER RECOIL STARTER COVER CHECK AND CLEANING Check Make sure that grass, clay, mud water or other similar material is not inside the recoil starter cover through the hole located on the side of the cover.

  • Page 48: Storage

    4MV488000.book 46 ページ ２０１６年３月２日　水曜日　午後１２時３６分 STORAGE STORAGE PREPARATION Proper storage preparation is essential for keeping your tiller trouble free and looking good. The following steps will help to keep rust and corrosion from impairing your tiller’s function and appearance, and will make the engine easier to start when you use the tiller again.

  • Page 49: Fuel

    4MV488000.book 47 ページ ２０１６年３月２日　水曜日　午後１２時３６分 STORAGE 2. After washing the tiller, wipe dry all accessible surfaces. 3. Start the engine outdoors, and let it run until it reaches normal operating temperature to evaporate any water remaining on the engine. 4. While the engine is running, operate the clutch lever to expel water from the pulleys, belts, and other moving items.
  • Page 50 4MV488000.book 48 ページ ２０１６年３月２日　水曜日　午後１２時３６分 STORAGE Draining the Fuel Tank and Carburetor 1. Place an approved gasoline container below the carburetor, and use a funnel to avoid spilling fuel. 2. Loosen the carburetor drain knob, and then move the fuel valve to the ON position.

  • Page 51: Engine Oil

    4MV488000.book 49 ページ ２０１６年３月２日　水曜日　午後１２時３６分 STORAGE Engine Oil Change the engine oil (see page 33). Engine Cylinder 1. Remove the spark plug (see page 39). 2. Pour a teaspoon (5 cm ) of clean engine oil into the cylinder. 3. Gently pull the starter grip several times to distribute the oil in the cylinder.

  • Page 52: Storage Precautions

    4MV488000.book 50 ページ ２０１６年３月２日　水曜日　午後１２時３６分 STORAGE STORAGE PRECAUTIONS If your tiller will be stored with gasoline in the fuel tank and carburetor, it is important to reduce the hazard of gasoline vapor ignition. Select a well ventilated storage area away from any appliance that operates with a flame, such as a furnace, water heater, or clothes dryer.

  • Page 53: Transporting

    4MV488000.book 51 ページ ２０１６年３月２日　水曜日　午後１２時３６分 TRANSPORTING BEFORE LOADING If the engine has been running, allow it to cool for at least 15 minutes before loading the tiller on the transport vehicle. A hot engine and exhaust system can burn you and can ignite some materials. To prevent fuel spillage, drain fuel from the fuel tank (see page 48).

  • Page 54: Taking Care Of Unexpected Problems

    4MV488000.book 52 ページ ２０１６年３月２日　水曜日　午後１２時３６分 TAKING CARE OF UNEXPECTED PROBLEMS ENGINE WILL NOT START Possible Cause Correction Fuel valve OFF. Turn valve ON. Choke OPEN. Move to CLOSE unless engine is warm. Engine switch OFF. Turn engine switch to ON. Out of fuel. Refuel (p.

  • Page 55: Engine Lacks Power

    4MV488000.book 53 ページ ２０１６年３月２日　水曜日　午後１２時３６分 TAKING CARE OF UNEXPECTED PROBLEMS ENGINE LACKS POWER Possible Cause Correction Air filter clogged. Clean or replace air filter (P. 36). Bad fuel, tiller stored without Drain fuel tank and carburetor treating or draining gasoline, or (p.

  • Page 56: Technical Information

    4MV488000.book 54 ページ ２０１６年３月２日　水曜日　午後１２時３６分 TECHNICAL INFORMATION Serial Number Locations FRAME SERIAL NUMBER ENGINE SERIAL NUMBER Record the engine and frame serial numbers in the spaces below. You will need these serial numbers when ordering parts, and when making technical or warranty inquiries. Engine serial number: Frame serial number: Date purchased:...

  • Page 57: Carburetor Modification For High Altitude Operation

    4MV488000.book 55 ページ ２０１６年３月２日　水曜日　午後１２時３６分 TECHNICAL INFORMATION Carburetor Modification for High Altitude Operation At high altitude, the standard carburetor air-fuel mixture will be too rich. Performance will decrease, and fuel consumption will increase. A very rich mixture will also foul the spark plug and cause hard starting. Operation at an altitude that differs from that at which this engine was certified, for extended periods of time, may increase emissions.

  • Page 58: Specifications

    Spark plug gap 0.6 – 0.7 mm Refer to page 39. See your IN:0.10 ± 0.02 mm (cold) Valve clearance authorized Honda EX:0.15 ± 0.02 mm (cold) dealer. Other specification No other adjustments needed. NOTE: Specifications are subject to change without notice.
  • Page 59 4MV488000.book 57 ページ ２０１６年３月２日　水曜日　午後１２時３６分...
  • Page 60 4MV488000.book 58 ページ ２０１６年３月２日　水曜日　午後１２時３６分...

Table of Contents