Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Related Manuals for Lojer SALLI Series
Summary of Contents for Lojer SALLI Series
- Page 1 SALLI Hospital beds F1,F2,F3,H2,H4 Operating instructions Version 1.3 04.09.2015...
- Page 2 The defective parts removed from a product as part of a warranty case shall become the property of LOJER and shall be retained for by the End Customer for LOJER, if necessary. If these parts cannot be returned to LOJER upon request, LOJER is entitled to charge for a corresponding amount.
-
Page 3: Table Of Contents
Fault detection ....................... 21 Technical specifications ..................21 Data of the type plate and markings on the bed ..........22 Standards used ....................24 Spare parts and diagrams ................. 24 Contact information and references ..............34 Copyright © Lojer Oy, 2010... -
Page 4: Salli Hospital Bed
Operation instructions for Salli F1, F2, F3, H2 and H4 Hospital bed / Version 1.3 1 Salli hospital bed This document include instructions how to use Lojer’s SALLI hospital beds. Salli hospital beds have been designed for institutional and hospital use for adults and patients over 12 years of age and taller than 146cm. -
Page 5: Salli F-Model Bed Parts
• Bed rails, different versions; normal, raised and eco model • Lifting pole, (101910) • IV-pole, (60121, 60122) • Lift support, (Lift support 80 ru or Lift support 90 ru) • Food tray • Urine bag holder • Basket for accessories Copyright © Lojer Oy, 2015... -
Page 6: Safety Precautions
(danger of falling off the bed and increased entrapment risk when lift support is used) IMPORTANT! If the bed or its accessories has a malfunction, it must be removed from use immediately and be taken to a service. Copyright © Lojer Oy, 2015... -
Page 7: Measures To Be Taken Before Use
Ensure that there is sufficiently space around the bed and both over and under the bed for the different functions and mechanism. IMPORTANT! Ensure that the side rails function properly and can be locked in the upper position when/if needed. Copyright © Lojer Oy, 2015... -
Page 8: Use Of The Hospital Bed And Accessories
Lock and check the direction locking wheel by moving the headend of the hospital bed sideways. Castors locked (brake, red button down) Castors turn freely (pedal in middle position) Direction lock (green button down) Figure 3. Locking of the central locking castors Copyright © Lojer Oy, 2015... - Page 9 Before moving the bed it is advisable to detach some of the accessories to minimise the risk of collision if they are not needed in time of transportation. Lifting pole, lift support, IV- pole etc. accessories which expands remarkably needed space around hospital bed. Copyright © Lojer Oy, 2015...
-
Page 10: Mattress Platform Height Adjustment
(danger of entrapment). IMPORTANT! The hospital bed must always be left in the lowest position in order to minimise any risk of a patient falling from the bed. Copyright © Lojer Oy, 2015... -
Page 11: Adjustment Of The Backrest
(danger of entrapment). IMPORTANT! Always be careful when adjusting lying surface parts. Risk of entrapment between mattress surface parts and side rail. See figure 6. Copyright © Lojer Oy, 2015... -
Page 12: Trendelenburg Adjustment
Always locate in foot end of bed. Normal bed end Figure 8. Bed end models Bed ends are attached with hand wheels screw. See figures 1 and 2. To tighten bed end, turn clockwise, to remove bed end open anti-clockwise. Copyright © Lojer Oy, 2015... -
Page 13: Bed Side Rail
Recommended mattress height with normal model side rail is max. 13cm. Locking knob, pull down to install or remove side rail. After install, check that knob is in up position for correct locking function Figure 9. Side rail attachment below upper frame Copyright © Lojer Oy, 2015... - Page 14 A rail, which is in the middle or intermediate position will not prevent a patient’s fall from the bed. Consequently, if a rail is in the middle position, it does not meet the requirements of standard IEC 60601-2-52 and the patient safety is endangered. Copyright © Lojer Oy, 2015...
-
Page 15: Raised Side Rails ( 1332Skkpkor )
A bed rail, which is in the middle or intermediate position will not prevent a patient’s fall from the bed. Consequently, if a rail is in the middle position, it does not meet the requirements of standard IEC 60601-2-52 and the patient safety is endangered. Copyright © Lojer Oy, 2015... -
Page 16: Eco Model Side Rails (1332Kskp, 70524Kp)
Side rail lock knob Plastic bearing, both ends of bed Figure 12. Eco model rail assembly, head and foot end of bed Recommended mattress height for 1332KSKP is maximum 13 cm and for 70524KP maximum 18 cm. Copyright © Lojer Oy, 2015... -
Page 17: Installation Of The Lifting Pole (101910)
Lift support can be used only along with normal side rails. When eco side rails are in use, lift support is not available. Maximum safe working load for side rails is 50 Kg. Copyright © Lojer Oy, 2015... - Page 18 If there is a risk that the patient may fall down from the bed the ride rails has to be kept at the upper position when the patient is left without monitoring. (danger of falling down and of entrapment when lift support is used) Copyright © Lojer Oy, 2015...
-
Page 19: Installation Of The Iv-Pole (60121 Or 60122)
Urine bag holder Raise the backrest. Remove the short mattress platform ABS middle part from the bed. The urine bag holder is fastened by pushing it through the holes on the frame. Figure 15. Urine bag holder Copyright © Lojer Oy, 2015... -
Page 20: Short Frame Assembly To Ease Transport
Secure that head part is completely locked and both locking knobs are into locked position (pushed in). Figure 17. How to remove head part Copyright © Lojer Oy, 2015... -
Page 21: Cleaning And Disinfection
Detach the middle platform by lifting. When you put it back, check to set the plate in the correct direction and proper place. Leg end of the bed Head end of the bed Figure 18. Normal layout of mattress platform ABS parts. Copyright © Lojer Oy, 2015... -
Page 22: Service
• Read manuals and check for correct functionality of the bed mechanics • Always repair or service only unoccupied beds • Always make notice for done maintenance or repair work in service form • Use only original spare parts which are proven by manufacturer Copyright © Lojer Oy, 2015... -
Page 23: Annual Service Schedule
• Check again done service work to ensure proper function of bed • Fill out following annual service report like below. You find a copy in the end of manual section 10 spare parts and diagram Copyright © Lojer Oy, 2015... -
Page 24: Fault Detection
Operation instructions for Salli F1, F2, F3, H2 and H4 Hospital bed / Version 1.3 8 Fault detection In order to purchase spare parts please contact the Lojer sales (please see Chapter 14 Contact information). Before contacting us, please ensure that you have the following information available: •... -
Page 25: Data Of The Type Plate And Markings On The Bed
F models. Figure 20. Warning for use or assembly of incompatible Figure 21. Instructions for mattress specification Figure 22. Safe working load: 1 max. patient weight, 2 safe working load Copyright © Lojer Oy, 2015... - Page 26 Figure 26. Information marked with this symbol must always be read and strictly observed Figure 27. Warning notice on sitting/standing in the end of bed, hazard area see figure below Figure 28. Hazard area on mattress platform Copyright © Lojer Oy, 2015...
-
Page 27: Standards Used
Operation instructions for Salli F1, F2, F3, H2 and H4 Hospital bed / Version 1.3 9.2 Standards used Lojer Salli hospital beds meet the requirements of directive 93/42/ETY (medical devices) and its amendments. The following unified standards have been adapted in the design and testing of the bed models: •... - Page 28 Operation instructions for Salli F1, F2, F3, H2 and H4 Hospital bed / Version 1.3 Copyright © Lojer Oy, 2015...
- Page 29 Operation instructions for Salli F1, F2, F3, H2 and H4 Hospital bed / Version 1.3 Copyright © Lojer Oy, 2015...
- Page 30 Operation instructions for Salli F1, F2, F3, H2 and H4 Hospital bed / Version 1.3 Copyright © Lojer Oy, 2015...
- Page 31 Operation instructions for Salli F1, F2, F3, H2 and H4 Hospital bed / Version 1.3 Copyright © Lojer Oy, 2015...
- Page 32 Operation instructions for Salli F1, F2, F3, H2 and H4 Hospital bed / Version 1.3 Copyright © Lojer Oy, 2015...
- Page 33 Operation instructions for Salli F1, F2, F3, H2 and H4 Hospital bed / Version 1.3 Copyright © Lojer Oy, 2015...
- Page 34 Operation instructions for Salli F1, F2, F3, H2 and H4 Hospital bed / Version 1.3 Copyright © Lojer Oy, 2015...
- Page 35 Operation instructions for Salli F1, F2, F3, H2 and H4 Hospital bed / Version 1.3 Copyright © Lojer Oy, 2015...
- Page 36 Operation instructions for Salli F1, F2, F3, H2 and H4 Hospital bed / Version 1.3 Copyright © Lojer Oy, 2015...
-
Page 37: Contact Information And References
Tel. 010 830 6750 Email: service@lojer.com www.lojer.com/huolto Sales Tel. 010 830 6700 Email: firstname.lastname@lojer.com References ScanAfia PRO S 2, S 4, TK 2 and TK 4 Hospital bed Service manual Salli F,H and F/H GPM model quick instructions Copyright © Lojer Oy, 2015...