Related Manuals for Watson-Marlow 701S/R
Summary of Contents for Watson-Marlow 701S/R
- Page 1 701S/R Drive/s: Issue 4 EPROM: Pumphead/s: Issue1 Watson-Marlow manual control high flow pump Installation and operating instructions Publication PB 0142 Issue 2...
-
Page 2: Table Of Contents
Limited, Falmouth, Cornwall TR11 4RU, England. Telephone 01326 370370 Fax 01326 376009 When the 701S/R pump is to be installed into a machine or is to be Declaration of assembled with other machines for installations, it must not be put into... -
Page 3: Two-Year Warranty
· accidental damage or electrical surge are excluded. Warranties purporting to be on behalf of Watson-Marlow Limited made by any person, including representatives of Watson-Marlow Limited, its subsidiaries, or its distributors, which do not accord with the terms of this warranty shall not be binding upon Watson-Marlow limited unless expressly approved in writing by a Director or Manager of Watson-Marlow Limited. -
Page 4: Recommended Operating Procedures
Recommended operating procedures DO keep delivery and suction lines as short as possible. DO use the minimum number of bends in rigid pipe runs. If there must be a bend, use a swept bend and not a tight elbow DO use suction and delivery pipelines with a bore equal to or larger than the bore of the tube fitted in the pumphead. -
Page 5: Part 1: 701S/R Drive
If required, the plug can be removed and a drain hose connected. Installation The 701S/R is suitable for single phase mains electricity only. Ensure that the Supplies supply voltage and frequency correspond with those marked with a white dot on the rear panel, (220V 50/60Hz, 120V 50/60Hz or 100V 50/60Hz). -
Page 6: Part 2: Operation
Wait 10 seconds and press the green start button. The speed control range of the 701S/R is from 2% to 100% of the rated maximum speed (360rpm at the rotor). The speed setting dial has a locking knob to prevent accidental speed changes. -
Page 7: Part 3: Maintenance
Part 3: Maintenance Fitting a second pumphead 701S/R pump may be fitted with one 701RX extension pumphead to give two Tubing channels of flow. There is no restriction on the size of tube which can be used considerations in each pumphead when two pumpheads are fitted, but if two tubes of 25.4mm bore are fitted, the maximum output pressure against which the... -
Page 8: Tube Loading
7. Tighten the track securing bolt with the Allen key provided to prevent removal by hand. The Allen key size is 6mm. Spare Allen keys are available from Watson-Marlow Limited or its distributors. When the track has been fitted, screw down both the spring adjuster nuts fully. - Page 9 Start the pump, allow any excess tubing to work through the pumphead, and Retensioning press the delivery end clamp down firmly. Check the tube for movement when the tubing the pump is running. If there is any sign of the tube working its way through the pumphead, the tube should be more firmly clamped at its suction end, the delivery end unclamped to release any excess tubing, pulled tight and then firmly reclamped again.
-
Page 10: Part 4: Appendices
Tubing range Pump performance depends upon the accuracy and consistency of the tubing. Watson-Marlow tubing is specially formulated for peristaltic pumping and it is manufactured and quality controlled to our own specifications. We recommend Marprene tubing whenever it is chemically suitable. -
Page 11: Specification
EMC Directive: 89/336/EEC and EN50081-1/EN50082-1 Care and maintenance The 701S/R uses a permanent magnet direct current motor with a pulse- width-modulated speed controller which provides black commutation. The only scheduled maintenance required for the 701S/R is inspection of the motor brushes and their replacement before their length is less than 10mm. - Page 12 Pumphead spares Page 12...
- Page 13 Page 13...
- Page 14 Drive spares Page 14...
- Page 15 Outline drawing Page 15...
- Page 16 Before returning any product for service, this form must be completed and sent to IMPORTANT Watson-Marlow, or its subsidiary, or its official distributor undertaking the service Watson-Marlow Limited, Falmouth, Cornwall TR11 4RU, England. Tel 01326 370370, Fax 01326 376009 Page 16...