Ready To Arm - SECOLink KM24 Short User Manual

Intruder alarm system
Stay arming mode
Use this mode when you are staying at home, but expect someone to use the entrance door later. Interior zones will
not be protected and you may freely move throughout the premises. Late arrivals can enter through the designated
entrance door without causing an alarm, but they must disarm the system within the entry delay period or an alarm
will occur. There are two ways to arm your security system's Stay arming mode:
for EU countries –
for non-EU countries –
Max Away arming mode
Use this mode when no one will be staying on the premises for a long period of time (e.g., vacations). Close all
protected perimeter windows and doors before arming. When armed in Max Away mode, all zones will be secure,
entry delay will turn off, and the system will sound an alarm if a protected zone is violated. There are two ways to arm
your security system's Max Away arming mode:
for EU countries –
for non-EU countries –
Night arming mode
Use this arming mode when you are staying inside the premises and require increased security. Interior zones are
disarmed and you may freely move throughout the premises. In the event of someone opening the door there will
not be an entry delay and the alarm will sound. This arming mode is effective when doors and windows are secured
with opening sensors, or glass break detectors are installed. There are two ways to arm Night Arming mode:
for EU countries –
for non-EU countries –
Partial Arming
Partitions allows you to break up a large area into smaller sections. Use this arming mode to arm certain areas of the
premises while leaving other areas disarmed, or to limit other user's access in specific areas. For example: an alarm
system is installed in a two-story house. During night time the ground floor isn't being used and all sensors of this
partition are armed. There will be an entry delay in the event of someone opening the door. Below is an example of
how to arm a first partition (one of two) in Away mode.
for EU countries – , Away ,
10/02 . . 25°C 14:02

READY TO ARM

1st Floor
2nd Floor
Press the key.
for non-EU countries – , Away ,
10/02 . . 25°C 14:02
READY TO ARM
1st Floor
2nd Floor
Press the key.
Arming and disarming of security barrier, "Pre-Alarm" mode
Microwave or infrared rays based security barriers, outdoor PIR detectors, which are connected to the system, can
be armed by Pre-alarm mode. In the event of someone crossing this electrical barrier the system will sound an
alarm without sending an alarm message to Central Monitoring Station. The Pre-alarm mode can be turned on and
off the same way. Please follow the instructions below:
, Pre-Alarm , ,
1 1 1 1
ENT ENT ENT ENT
10/02 . . 25°C 14:02
READY TO ARM
1st Floor
2nd Floor
Press the key.
Page 2
, Stay , .
ENT
, Stay
ENT
, Max Away
, Max Away
, Night , .
ENT
, Night .
ENT
, .
1 1 1 1
ENT
Partitions
Arming
1 1st Floor
Away
2 2nd Floor
Press [ENT] to arm
Press [ ] to select mode
Press [1]..[4] to select part.
Press the key.
1 1 1 1
, .
1 1 1 1 ENT
Partitions
Arming
1 1st Floor
Away
2 2nd Floor
Press [ENT] to arm
Press [ ] to select mode
Press [1]..[4] to select part.
Press the key.
1 1 1 1
.
Partitions
SOUNDS
1 1st Floor
Pre-Alarm
2 2nd Floor
Press [ENT] to confirm
Press [ ] to select mode
Press [1]..[4] to select part.
Press the key.
1 1 1 1
.
, .
ENT
.
ENT
#
Press the key. Enter your PIN code
ENT
#
Press the key. Leave the premises.
ENT
10/02
READY TO ARM
Press the key. Pre-alarm is turned on in
ENT
KM24, KM24A, KM24G keypad KM24, KM24A, KM24G keypad
To Exit
Arm
seconds
Enter PIN
. Leave the premises.
To Exit
30
seconds
. 25°C 14:02
1st Floor
2nd Floor
1st partition.
Short user manual
30