Ready To Arm - SECOLink KM24 Short User Manual

Intruder alarm system
Partial arming
This is universal way of arming, which enables to arm selected partition in desired arming mode.
Example: Only the first partition is armed. This kind of arming is available in 2-storied house, when at night
the ground floor isn't used, all sensors of this partition are armed. When somebody opens doors will be an
entry delay.
10-26 +25°C

READY TO ARM

READY TO ARM
1st Floor
2nd Floor
Press key.
Arming and disarming of security barrier, "Pre-Alarm" mode
Microwave or infrared rays based security barriers, also outdoor PIR detectors, which are connected to the
system, can be armed by "Pre-Alarm" mode. The system will sound an alarm (without sending alarm
message to Central Monitoring Station), when someone traverses this electrical barrier. The "Pre-Alarm"
mode can be turned on and turned off by marking/unmarking partitions with
partitions with ,
, [Pre-Alarm],
Bypassing zone
Bypassing a zone allows you to leave a door or window open while still arming the rest of your security
system. Bypass procedure can be made:
, [Zone bypass],
B B B B
BY BY BY BY ! ! ! !
Zones
1 Door
2 Hallway
3
Kitchen
4
Bedroom
5 Smoke detector
Zone isn't violated
There are two different bypass types: temporal or permanent. First is used for one arming and disarming cycle, second – until
the user unbypass the zone. Enter the zone number you would like to bypass. THIS MUST BE A TWO DIGIT NUMBER
(for the first zone – 01, for second – 02 and so on). The zone will be marked by "x". The last number should be pressed and
held for 2 sec to bypass the zone for a long time (permanently). The zone will be marked by capital "X". When all zones are
marked press the key. The same actions can be performed by selecting the zones with the keys
ENT ENT ENT ENT
marking/unmarking with the
Abort arming
For selection aborting, also arm procedure aborting the system SECOLink has the
in process and you want to abort arming, press the
Arming system with troubles
10-26 +25°C 01:44
EU standards unexpect using of the system, which has troubles. When key
Sys. Trouble Sys. Trouble color, the arming is impossible in the ways, which were described earlier. It is necessary immediately
AC Loss
eliminate troubles, also inform CMS and company, which had installed the system.
The system detects troubles in own modules, also it detects and other common troubles, like 230V
disappearance in AC line, disconnected phone line because of repair, battery discharge. In exceptional
cases is possible to bypass the troubles for a short time and arm system as usual.
It can be done this way:
Press the
the key backlight starts to blink fast. The blinking duration is 30 seconds. During this time is possible to make
usual arming procedure.
2
01:44
Arming Arming
Away Away
Press [ENT] to arm
Press[ ] to select mode
Press [1]..[4] to select part.
Press key to select arming
mode. For partial arming press
... keys.
4 4 4 4
! ! ! !
GHI GHI GHI GHI
keys and marking/unmarking with ,
... ,
4 4 4 4
1 1 1 1 ! ! ! ! ENT ENT ENT ENT PIN: PIN: PIN: PIN:
GHI GHI GHI GHI
, ...
PIN: PIN: PIN: PIN: 0 0 0 0
Zones
1 Door
2 Hallway
3
Kitchen
4
Bedroom
5 Smoke detector
Zone is violated
key (short press – temporal zone bypass, long – permanent zone bypass).
# # # #
key once – message about the trouble will be shown on the display. Press the
CLR CLR CLR CLR
Sritys
1 1st Floor
2
2 nd Floor
Using ...
1 1 1 1
partitions which have to be armed.
1 1 1 1
Press key to confirm the
ENT ENT ENT ENT
decision.
# # # #
or , and ,
9 9 9 9
# # # # ENT ENT ENT ENT
WXYZ WXYZ WXYZ WXYZ
Zones
1 Door
2 Hallway
3
Kitchen
4
Bedroom
5 Smoke detector
Zone is bypassed temporary
key and enter PIN code.
CLR CLR CLR CLR
keys check all System will be armed.
4 4 4 4
! ! ! !
GHI GHI GHI GHI
...
1 1 1 1
keys.
Zones
1 Door
2 Hallway
3
Kitchen
4
Bedroom
5 Smoke detector
Zone is bypassed permanently
CLR CLR CLR CLR
is backlighted with green
CLR CLR CLR CLR
KM24, KM24A keypad KM24, KM24A keypad
Short user manual
System System
wi ll be wi ll be
armed armed
keys or by selecting
4 4 4 4
! ! ! !
GHI GHI GHI GHI
or and by
key. If the exit delay is
key again –
CLR CLR CLR CLR