Related Manuals for H3C SecPath T9000 IPS Series
Summary of Contents for H3C SecPath T9000 IPS Series
- Page 1 H3C SecPath T9000 Intrusion Prevention System Series Installation Quick Start New H3C Technologies Co., Ltd. http://www.h3c.com.hk Document version: 5PW101-20170411...
- Page 2 Copyright © 2015-2017, New H3C Technologies Co., Ltd. and its licensors All rights reserved No part of this manual may be reproduced or transmitted in any form or by any means without prior written consent of New H3C Technologies Co., Ltd.
-
Page 3: Table Of Contents
Contents Installation quick start ·················································································································································· 2 Preparing for installation ·················································································································································· 2 Installing the IPS ································································································································································ 2 Attaching the slide rails or rack shelf to the rack ·································································································· 2 Installing cage nuts ··················································································································································· 3 Attaching the cable management brackets to the IPS ·························································································· 4 ... -
Page 4: Installation Quick Start
Installing the IPS IMPORTANT: The IPS is heavy. H3C recommends that you install the IPS at the bottom of the rack. The IPS is delivered without any filler panels in some card slots. The figures in this document are for illustration only. -
Page 5: Installing Cage Nuts
Figure 1 Locating the slide rail installation position (1) Middle of the narrower metal area between holes Installing cage nuts As shown in Figure 2, align the bottom edge of the mounting bracket with the top flange of the slide rail or the top surface of the rack shelf. Mark the cage nut installation position on the front rack post. -
Page 6: Attaching The Cable Management Brackets To The Ips
Figure 2 Installing cage nuts (T9006) Attaching the cable management brackets to the IPS The IPS uses signal cable management bracket and power cord management bracket to route the cables. You need to install the signal cable management bracket separately for the T9010 IPS. All other T9000 IPSs come with the signal cable management brackets secured to the mounting brackets. - Page 7 Attach the cable management bracket to the chassis and align the screws with the mounting holes in the chassis, as shown in Figure Fasten the screws. Figure 3 Attaching cable management brackets to a T9010 IPS (1) Attach the cable management bracket to the chassis (2) Screw holes for installing the cable management bracket (3) Screws for attaching the cable management bracket to the chassis (4) Signal cable management bracket (installed at the upper part of the chassis)
-
Page 8: Attaching The Mounting Brackets To The Ips
Figure 4 Attaching cable management brackets to a T9006 IPS (1) Attach the cable management bracket to the chassis (2) Screw holes for installing the cable management bracket (3) Screws for attaching the cable management bracket to the chassis (4) Power cord management bracket (installed at the lower part of the chassis) Attaching the mounting brackets to the IPS Identify the left and right mounting brackets by their marks L and R. -
Page 9: Installing The Ips In The Rack
Installing the IPS in the rack CAUTION: Do not use the fan tray handle, power module handle, filler panel handle, or air vents of the chassis to carry the IPS. Any attempt to carry the IPS with these parts might cause equipment damage or even bodily injury. -
Page 10: Grounding The Ips
Grounding the IPS CAUTION: Correctly connecting the grounding cable is crucial to lightning protection and EMI protection. Before • you use the IPS, ground the IPS reliably. • Use the (yellow-green double color) grounding cable provided with the IPS to ground the IPS. Connect the grounding cable to the earthing system in the equipment room. -
Page 11: Installing Cards
Insert the plug of the ESD wrist strap into the ESD socket in the IPS chassis. Figure 8 Attaching an ESD wrist strap (T9006) Installing cards IMPORTANT: The switching fabric modules for the T9010 and T9014 IPSs are delivered with protection boxes. Before you install such a switching fabric module, remove the protection box as follows: •... -
Page 12: Installing Power Modules
The installation procedure is the same for AC and DC power modules. This section uses an AC power module as an example. For more information about AC and DC power modules available for the IPS, see H3C SecPath T9000 Intrusion Prevention System Series Installation Guide. To install a power module: If the target power module slot has a filler panel installed, use a Phillips screwdriver to loosen the captive screws on the filler panel and remove the filler panel. -
Page 13: Connecting An Ac Power Cord
Figure 10 Installing a power module in a vertical slot (T9010 and T9014) Figure 11 Installing a power module in a horizontal slot (T9006) Connecting an AC power cord WARNING! Before you connect a power cord, make sure the circuit breaker at the power input end is switched off. To connect an AC power cord: Plug the AC power cord connector into the power receptacle of the power module. -
Page 14: Connecting A Dc Power Cord
Figure 12 Securing the AC power cord (T9006) Connecting a DC power cord WARNING! Make sure each power cord has a separate circuit breaker. • Before you connect a power cord, make sure the circuit breaker at the power input end is switched off. •... -
Page 15: (Optional.) Installing An Xfp/Sfp+/Sfp/Qsfp+ Transceiver Module
(Optional.) Installing an XFP/SFP+/SFP/QSFP+ transceiver module Unpack the transceiver module. Do not touch the golden plating on the transceiver module. Pivot the clasp of the transceiver module up. Holding two sides of the transceiver module, gently push the module into the slot until you feel that the bottom spring tab catch in the slot. For a QSFP+ module that uses a plastic pull latch, skip this step. -
Page 16: Obtaining Documentation
PC end. To disconnect a PC from an operating switch, first disconnect the switch end. Obtaining documentation To access the most up-to-date H3C product documentation on the H3C website at www.h3c.com.hk: Go to http://www.h3c.com.hk/Technical_Documents. Choose the desired product category and model. -
Page 17: Index
Connecting an AC power cord,1 1 Logging in to the IPS,13 Grounding the IPS,8 Obtaining documentation,14 Installing FRUs,8 Preparing for installation,2 Copyright © 2017 New H3C Technologies Co., Ltd.. For more information about the product and installation procedures, log in to www.h3c.com.hk...
Need help?
Do you have a question about the SecPath T9000 IPS Series and is the answer not in the manual?
Questions and answers