Subscribe to Our Youtube Channel
Related Manuals for Deprag MICROMAT-E 320E19-0008
Summary of Contents for Deprag MICROMAT-E 320E19-0008
- Page 1 012625EN Operating Instruction Booklet EC-Screwdriver, for stationary use 320E19-0002 405024 A 320E19-0008 405024 B 320E19-0005 405024 C MICROMAT-E...
-
Page 2: Table Of Contents
DEPRAG Representative, one of our international support offices or us direct at DEPRAG. We will be happy to answer any questions. Please visit our web site: www.deprag.com Content 1 SAFETY TIPS ........................3 1.1. General Safety Tips ....................3 1.2. -
Page 3: Safety Tips
Safety Tips 1.1. General Safety Tips Before operating tool, make sure to carefully read and always observe these operating instructions Generally, the operator of the equipment and/or machinery is responsible for the equipment’s perfect condition and operation, while observing all necessary safety regulations. -
Page 4: General Safety Regulations For Electronic Screwdriver Spindles
1.2. General Safety Regulations for Electronic Screwdriver Spindles · Disconnect the spindle from the power supply, prior to changing bits. · Do not wear loose clothing or jewelry; for movable parts can seize them. Wear a hairnet, if operator has long hair. ·... -
Page 5: Owner Obligation
1.3. Owner Obligation The owner is obliged to only let persons operate the equipment, who · are familiar with basic work environment safety rules and accident- preventing regulations. Also, those persons must have been instructed in the correct use of the equipment. ·... -
Page 6: Warranty And Liability
1.5. Warranty and Liability Unless otherwise specified, our “General Sales and Delivery Conditions” apply. Warranty and liability claims in regards to persons or equipment damages are invalid, if one or several of the following causes apply: · Use of the equipment in a non-designated application. ·... -
Page 7: Symbol Description
1.6. Symbol Description Read and observe the Operating Instruction Booklet, prior to and during operation of tool. DANGER Reference to an immediate danger to a person. May lead to serious injuries or even death, if unobserved! Properly recycle environmentally damaging grease, cooling agents or detergents. - Page 8 Maintenance and repair on hydraulic and pneumatic equipment may only be performed by specially trained personnel! Disconnect equipment from air supply, prior to repair of pneumatic or hydraulic equipment. Provide regular preventive maintenance on hoses and airlines. Exchange hose lines, even if there is no visible damage! (Observe corresponding requirements of the manufacturer!) After repair and maintenance, check the following items: ·...
-
Page 9: Observe Environmental Regulations
· Multi-Spindle Screwdriving Stations · Cartesian Screwdriving Robots · Gantry Screwdriving Cells The DEPRAG EC Screwdriver Spindles allow free programming of the screw tightening process. Within the power range of the selected spindle, · the torque value, · the speed, ·... -
Page 10: General
General The EC-Screwdriver 320E… is part of the EC-Screwdriving System. The essential characteristics of this screwdriver series are: · brush-less EC-Drive with commutator over encoder · torque- and angle-controlling The EC-Screwdriving System is designed for the use in an industrial envi- ronment for a maximum torque of 0,2 / 0,5 resp. - Page 11 The controller’s integrated display and operating unit indicates the operating mode and assembly status. It also allows a direct change of parameters (such as speed, torque and angle values etc.) within the assembly process and without the need of a PC connection. In automatic mode, the AST10 communicates with the system’s PLC.
-
Page 12: Installation
Installation see item Dimensional Drawing as well as Operating Instructions EC- Screwdriving System Sequence Controller AST10-1 Motor Cable KMO-AST10 Screwdriver 320E... Measuring Cable KN-AST10 Picture: Installation... -
Page 13: Operation
Operation Trained personnel may operate the EC-Screwdriver Spindle only. Proceed with the operating according to the Operating Instructions of the EC- Screwdriving System - Operation. Handling DANGER Make sure to always disconnect the Screwdriver Spindle from the power supply, when performing maintenance, adjustments or disassembly. -
Page 14: Change Of Bits
Change of bits DANGER Make sure to disconnect the Spindle from the power sup- ply, prior to changing of bits. This will avoid that Spindle starts unintentionally and creates an injury. INFORMATION The Screwdriver Spindle is equipped with a quick change chuck. Use high-quality bits in accordance to the DIN-Norm 3126 only. -
Page 15: Dimensional Drawing
Dimensional Drawing... -
Page 16: Maintenance And Upkeep
· In case of tool malfunctions, we recommend sending the tool to DEPRAG. 10 Trouble Shooting Please refer to the Operating Instructions of the EC-Screwdriving System. 11 Delivery Capacity Unused machines should be stored in a dry, locked area. -
Page 17: Accessories - Optional Equipment
403280 B See also Operating Instructions of the EC-Screwdriving System and leaflet D 3165 E All leaflets are available for download from our web site: www.deprag.com INFORMATION You will find suitable inserting tools · in our brochure D 3320 E or ·... -
Page 18: Technical Data
14 Technical Data Manufacturer DEPRAG SCHULZ GMBH u. CO. Address Kurfürstenring 12 - 18 Postfach 1352 D-92224 Amberg D-92203 Amberg Phone 09621/371-0 09621/371-120 Technical Data: 320E19-0002 320E19-0008 320E19-0005 405024 A 405024 B 405024 C Torque min. (Nm/in.lbs) 0.03 / 0.3 0.15 / 1.5... -
Page 19: Disposal
15 Disposal Disassemble the machine for the required disposal complete. Observe local and environmental regulations for the separation and recycling of materials. -
Page 20: Declaration Of Manufacturer
16 Declaration of Manufacturer EC-Declaration of Manufacturer in accordance with the CE-Machine-Guideline 98/37/EC, appendix II B DEPRAG SCHULZ GMBH u. CO. Kurfürstenring 12 – 18 Postfach 1352 D-92204 Amberg D-92203 Amberg declares, that the construction of the EC-Screwdriver Spindle 320E19-0002... -
Page 21: Service Locations And Authorized Partners
Fax: +49 (0) 9621 / 3 71-1 20 PR CHINA Internet: http://www.deprag.com DEPRAG China IRELAND e-mail: info@deprag.de DEPRAG Assembly Technologies Production Equipment Ltd. (Suzhou) Co., Ltd. Riverside Commercial Estate GREAT BRITAIN No. 111, Hong Ye Rd, Blk. 4 Unit D IRL-Galway DEPRAG Ltd. - Page 22 Tel.: +1 / 972 / 221 – 8731 SLOVENIA Fax: 00370 / 37 / 760.500 Fax: +1 / 972 / 221 – 8163 MB-NAKLO D.O.O. Internet: http://www.hidroteka.lt Toll Free: (800) 4 DEPRAG Toma Zupana 16 e-mail: hidroteka@hidroteka.lt Internet: http://www.deprag.com SLO-4202 NAKLO e-mail: deprag@depragusa.com LUXEMBOURG Tel.: +386 (0) 4 / 277 17 00...
- Page 24 DEPRAG SCHULZ GMBH u. CO. Postfach 1352, D-92203 Amberg Kurfürstenring 12-18, D-92224 Amberg (09621) 371-0 (09621) 371-120 Internet: http://www.deprag.com e-mail: info@deprag.de...
Need help?
Do you have a question about the MICROMAT-E 320E19-0008 and is the answer not in the manual?
Questions and answers