Related Manuals for Deprag 345-308U
Summary of Contents for Deprag 345-308U
- Page 1 012203EN Operating Instruction Booklet Pneumatic Screwdriver 345-308U 339269 A 345-408U 345764 A 345-508U 339270 A 345-708U 385163 B MICROMAT...
-
Page 2: Table Of Contents
We kindly ask that you read these operating instructions carefully so that you will be able to use this tool safely and for many years to come. If you need additional information, please contact your DEPRAG Representative, one of our international support offices or us direct at DEPRAG. -
Page 3: Safety Tips
Safety Tips 1.1. General Safety Tips Before operating tool make sure to carefully read and observe this operating instruction. Generally, the operator of the equipment and/or machinery is responsible for the equipment’s perfect condition and operation, while observing all necessary safety regulations. -
Page 4: General Safety Tips For Pneumatic Screwdriver Spindles
1.2. General Safety Tips for Pneumatic Screwdriver Spindles · Disconnect the tool from the air supply, when changing bits or when readjusting clutch. · Do not wear wide clothing or jewelry, for they can be seized by movable parts. Wear a hairnet if operator has long hair. ·... -
Page 5: Owner Obligation
1.3. Owner Obligation The owner is obliged to only let persons operate the equipment, who · are familiar with basic work environment safety rules and accident- preventing regulations. Also, those persons must have been instructed in the correct use of the equipment. ·... -
Page 6: Symbol Description
1.6. Symbol Description Read and observe the Operating Instruction Booklet, prior to and during operation of tool. DANGER Reference to an immediate danger to a person. May lead to serious injuries or even death if unobserved! Properly recycle environmentally damaging grease, cooling agents or detergents. -
Page 7: Observe Environmental Regulations
Maintenance and repair on hydraulic and pneumatic equipment may only be performed by specially trained personnel! Disconnect equipment from air supply, prior to repair of pneumatic or hydraulic equipment. Provide regular preventive maintenance on hoses and airlines. Exchange hose lines, even if there is no visible damage! (Observe corresponding requirements of the manufacturer!) After repair and maintenance, check the following items: ·... -
Page 8: Designated Equipment Use
Designated Equipment Use DEPRAG MICROMAT / MINIMAT-Screwdrivers of straight shape are used for manual torque-controlled assemblies, preferably for vertical applications. Installation · Blow out air line and pressure hose, prior to connection it to the tool. · Make sure, that all air lines have a sufficient cross-section (see technical data) and hoses must be free of bends and kinks. - Page 9 In regards to air-quality according to ISO8573-1, we recommend: LASS ESIDUE ESIDUE OF ESIDUE OF ATER Pressure Particle Content Concentration Dew Point Concentration Size mm mg/m³ max. mg/m³ max. g/m³ Lubricated Air Dry Air 0,88 Picture: Connection of a DEPRAG MICROMAT-Screwdriver...
- Page 10 Recommended Accessories Balancer, spring loaded EIGHT APACITY ENGTH EIGHT – (kg) (kg) FROM 0 – 0,5 827676 A 0,3 – 1,2 827677 A 1 – 2 827678 A 2 – 3 808690 A Hose Balancer, spring loaded EIGHT APACITY ONNECTION EIGHT I.D.
-
Page 11: Operation
If necessary, exchange clutch spring. The required torque adjustment can be checked, using a DEPRAG Torque Wrench or Measuring Platform (see DEPRAG catalogs D 3020 and D 3022). This equipment can also be used to re-adjust the torque of the Screwdriver. -
Page 12: Range And Exchange Of Clutch Spring
4.1. Range and Exchange of Clutch Spring The torque range of the DEPRAG Screwdriver is adjustable. Please see a listing for the torque ranges of the color-coded springs below. Torque Range of the individual clutch spring: -Æ OLOR ORQUE ORQUE... -
Page 13: Torque Adjustment
clutch spring hex of the clutch shaft adjustment nut Picture: Exchange of clutch spring Make sure to screw adjustment (adjusting) nut onto clutch bearing until one line of the thread is visible. 4.2. Torque Adjustment Disconnect driver from air-supply. Unscrew spring sleeve (Optional Equipment) (left hand thread). Unscrew clutch bearing (left hand thread). -
Page 14: Handling
Handling The operation of the DEPRAG MICROMAT-Screwdriver is very simple. Grip the Screwdriver as illustrated on the picture “Connection of a DEPRAG MICROMAT-Screwdriver”. As soon as you put the bit onto the screw and slightly push the screwdriver down, it will start running. After reaching the preset torque, the automatic clutch will disengage and turn off the Screwdriver. -
Page 15: Disassembly - Assembly
After repair or maintenance, verify that equipment runs to specification! Principally, use only DEPRAG original spare parts. Otherwise, a reduction in equipment power-output and an increased maintenance-requirement occurs. If NON-DEPRAG parts are installed, DEPRAG is justified to void any existing warranty and liability obligations. ATTENTION... - Page 16 Press the two ball bearings from the bearing covers. NOTE The minimum vanes width should be 3 mm. Assembly: Use the DEPRAG Grease 807293 (100-g tube) to grease the ball bearing, needle bearing and gearing parts prior to reassembly. a. Clean rotor.
-
Page 17: Special Repair Tools (Optional Equipment)
Put the motor- and gearing package as well as the valve housing 3265002 together and slide the motor housing 323683 resp. 325349 over them until thread stops. Put the pressure pin 460778 into the valve bushing 328050 and use the pressure pin to screw in the valve housing 3265002 (right-hand thread). -
Page 18: Spare Parts Drawings
6.2. Spare Parts Drawings... -
Page 23: Dimensional Drawing
6.3. Dimensional Drawing... -
Page 24: Maintenance And Upkeep
6 months (single shift). · Exchange broken or worn inserting tools immediately, for they can cause injury to the Operator. · If tool malfunctions, we recommend to send the machine to DEPRAG. 7.1. Wear Parts UANTITY... -
Page 25: Trouble Shooting
Maintain air pressure of 90 PSI shut-off or for required torque ratchets value Valve Pin is too long Check length of valve pin, either shorten or replace valve pin (picture: Actual Size of Valve Pin) If necessary, please send tool to DEPRAG for service. -
Page 26: Delivery Capacity
Picture: Actual Size of Valve Pin Attention: When connecting to compressed air supply valve pin may be catapulted out which may cause serious injuries. When verifying the actual size of the valve pin, make sure N O T to hold the screwdriver directed towards yourself or any other person. -
Page 27: Accessories - Optional Equipment
· Insert finder into the spring sleeve, place pressure spring into finder and tighten all items to the clutch bearing (left-hand thread). INFORMATION You will find suitable inserting tools · in our brochure D 3320 E or · on the internet as follows: ® Screwdriving www.deprag.com Technology® Selection program: Inserting tools... -
Page 28: Storage
Picture: Screwdriver with sponge rubber handle 833058 11 Storage Unused machines should be stored in a dry, locked area. -
Page 29: Technical Data
12 Technical Data Manufacturer DEPRAG SCHULZ GMBH u. CO. Address Kurfürstenring 12 - 18 P.O. Box 1352 D-92224 Amberg D-92203 Amberg Phone 09621/371-0 09621/371-120 Technical Data: 345-308U 345-408U 345-508U 345-708U 339269 A 345764 A 339270 A 385163 B Screws (up to) Torque min. -
Page 30: Disposal
13 Disposal Unused machines should be stored in a dry, locked area. Disassemble the machine for the required disposal complete. Observe local and environmental regulations for the separation and recycling of materials. Recycle waste oil to avoid environmental contamination! Waste Oil... -
Page 31: Conformity Declaration
14 Conformity Declaration EC-Conformity Declaration according to the EC-Machine-Guidelines 98/37/EC, Amendment IIA DEPRAG SCHULZ GMBH & CO. PO Box 1352 D-92203 Amberg hereby confirm, that the design of the screwdriver 345-308U 345-408U 345-508U 345-708U conforms to the following, relevant regulation: EC-Machine-Guidelines, Version 98/37/EC, Amendment No. -
Page 32: Service Locations And Authorized Partners
15 Service Locations and Authorized Partners ALGERIA CZECHIA/SLOWAKIA GREAT BRITAIN EP-Technology Trading S.U.A.R.L. DEPRAG CZ a.s. DEPRAG Ltd. 29 Rue Ahmed Tlili - ZI Borj Cedria ul. T.G. Masaryka 113 Unit B4, Pegasus Court TN-2055 Bir el Bey Tunis - Tunisia CZ -50781 Lázně... - Page 33 ISANDO LUXEMBOURG Tel.: +1 / 972 / 221 – 8731 1601 Fax: +1 / 972 / 221 – 8163 Republic of South Africa Toll Free: (800) 4 DEPRAG Postal deliveries: Parelhoenstraat 24 Internet: http://www.deprag.com P.O. Box 1162 9080 Lochristi e-mail: deprag@depragusa.com...
- Page 36 DEPRAG SCHULZ GMBH u. CO. Postfach 1352, D-92203 Amberg Kurfürstenring 12-18, D-92224 Amberg (09621) 371-0 (09621) 371-120 Internet: http://www.deprag.com e-mail: info@deprag.de...