Table of Contents
Advertisement
Quick Links
HPE Apollo a6000 Chassis
Quick Setup Instructions
© Copyright 2014, 2016 Hewlett Packard Enterprise Development LP
The information contained herein is subject to change without notice. The
only warranties for Hewlett Packard Enterprise products and services are set
forth in the express warranty statements accompanying such products and
services. Nothing herein should be construed as constituting an additional
warranty. Hewlett Packard Enterprise shall not be liable for technical or
editorial errors or omissions contained herein.
Part Number: 755708-003
October 2016
Edition: 4
Site requirements
Select an installation site that meets the detailed installation site
requirements described in the setup and installation guide on the
Hewlett Packard Enterprise website
(http://www.hpe.com/info/Apollo_6000/docs).
Verifying the pallet contents for
the chassis
Item
Description
1
HPE Apollo a6000 Chassis
2
Server tray blank*
3
Server tray*
4
Fan assembly (5)
5
I/O module
6
Power cage (right)
7
Management module
8
Power cage (left)
9
Power management cable**
10
HPE Apollo a6000 Chassis Rail kit**
11
Service tray* **
* The quantity depends on the configuration ordered.
** Not shown
Advertisement
Table of Contents
Related Manuals for HPE Apollo a6000
Summary of Contents for HPE Apollo a6000
- Page 1 Power cage (right) Management module Power cage (left) Power management cable** HPE Apollo a6000 Chassis Rail kit** Service tray* ** * The quantity depends on the configuration ordered. ** Not shown © Copyright 2014, 2016 Hewlett Packard Enterprise Development LP The information contained herein is subject to change without notice.
-
Page 2: Setting Up The Chassis
The following figure identifies the fan assemblies by device Setting up the chassis number. Select the proper location for the chassis to be set up, based on requirements detailed in the HPE Apollo a6000 Chassis Setup and Installation Guide on the Hewlett Packard Enterprise website (http://www.hpe.com/info/Apollo_6000/docs). -
Page 3: Installing The Chassis Into A Rack
Hewlett Packard Enterprise website (http://www.hpe.com/info/qs). Installing the chassis into a rack Installing a server To install the chassis into a rack, see the HPE Apollo a6000 Chassis CAUTION: To prevent improper cooling and thermal Setup and Installation Guide on the Hewlett Packard Enterprise damage, operate server trays only when the open side of website (http://www.hpe.com/info/Apollo_6000/docs). -
Page 4: Installing A System Fan
Install the server tray. When seated properly, the server tray Installing a system fan will be flush with the front of the chassis and the release lever will close completely without resistance. Installing a power cage Installing the rear components CAUTION: To prevent damage to the component, power down the chassis and disconnect all power cords CAUTION: To prevent improper cooling and thermal... -
Page 5: Installing The Power Shelf
To install the component: Install the power shelf rack rails into the rack. For more information, see the HPE Power Shelf Rack Rail Kit for HPE and Third Party Racks Installation Instructions. Install the power shelf. -
Page 6: Connecting The Chassis To A Power Shelf
Install the 12V DC power cables: Install the power supply vent cover to protect the power supply vents. a. Insert the cable through the wide opening on either end of the power shelf, and then connect it to the appropriate connector. -
Page 7: Example Configurations
Example configurations Configuration examples can be calculated using the HPE Power Advisor Tool (http://www.hpe.com/info/poweradvisor/online). This tool is designed for facilities planning purposes only. Values obtained from the tool are based on worst case loads. Whenever possible, Hewlett Packard Enterprise recommends using actual measurements in configuration planning. -
Page 8: Connecting The Optional Hpe Apm Module
IMPORTANT: If you have an HPE APM module connected to an Apollo a6000 Chassis, do not connect the iLO port of the HPE APM module and the iLO port of the enclosure to the network at the same time. Having both ports connected at the same time results in a loopback condition. -
Page 9: Documentation Feedback
Connect the HPE APM module to the power shelf (shown in The documents are on the Hewlett Packard Enterprise website (http://www.hpe.com/support/proliantgen9/docs). blue). The installation is complete. For more information For more detailed setup and configuration information, see the Advanced Power Manager User Guide. For safety information and...