Problems And Corrective Actions - Krups EA8050 Manual

The appliance does not switch on when the
"On/Off" is pressed.
Water or steam comes incorrectly out of the
steam nozzle.
The espresso or coffee is not hot enough.
The coffee is too light or not strong enough.
The coffee flows too slowly.
The coffee is not creamy enough.
The appliance does not serve any coffee.
You have used ground coffee instead of bean
coffee.
The grinder makes a strange noise.
The grinding fineness knob is hard to turn.
The steam does not come out of the nozzle.
There is not enough milk froth.
The milk froth is too bubbly.
The Auto-Cappuccino accessory does not suck
the milk (accessory sold separately).
After filling the water tank, the warning mes-
sage is still displayed.
The cleaning or descaling programme will not
start.
After emptying the used coffee collector, the
warning message is still displayed.
After washing the cleaning drawer, the warning
message is still displayed.
The power has been cut off during a cycle.
There is water or coffee underneath the
appliance.
A message "Fault n° XX" appears.

PROBLEMS AND CORRECTIVE ACTIONS

Check that the plug of the power cord is pushed correctly into the mains
socket.
In case of repeated operation, several drops may drip from the steam noz-
zle.
Change the coffee temperature setting.
Heat the cups by rinsing them with hot water.
Check that the coffee bean tank has coffee in it and that it is flowing correctly.
Avoid using oily, caramelised or flavoured coffee.
Reduce the volume of coffee using the central knob.
Turn the grinding fineness knob towards the left for a finer grind.
Prepare in two cycles using the 2 cup function.
Turn the grinding fineness knob towards the right for a coarser grind (may
depend on the type of coffee used).
Carry out one or two rinsing cycles.
Turn the grinding fineness knob towards the left for a finer grind (may
depend on the type of coffee used).
Change the Claris cartridge (follow the installation procedure on page 3).
Carry out one or two rinsing cycles.
An incident has been detected during the preparation. The appliance resets
itself automatically and is then ready for a new cycle.
Use your vacuum cleaner to suck out the pre-ground coffee in the coffee
bean tank.
There are foreign particles in the grinder.
Contact KRUPS' Customer Service.
Only change the grinder setting when it is operating.
After switching off your appliance and leaving it to cool:
Clean and unblock all of the outlets of the nozzle with the needle supplied
(see page 7). Unblock the outlet of the support pipe of the steam nozzle
with the needle supplied. Remove the Claris cartridge.
Using the needle supplied unblock the small air inlet at the top of the nozzle
if required.
Use a cold recipient and milk that has been opened recently.
Try changing the type of milk if this does not work (UHT or pasteurised).
Check that the two ends of the small stainless steel tube are fitted correctly
into the flexible part of the steam nozzle.
Ensure that the tube immersed in the milk is not blocked.
Check that the flexible tube is fitted correctly into the accessory to avoid air
leaks.
After switching of your appliance and leaving it to cool, unblock the outlet of
the Auto-Cappuccino accessory.
Check that the tank is fitted correctly onto the coffee machine.
Check that the float at the bottom of the tank moves freely.
Rinse the tank and descale if necessary.
Unplug the appliance for 20 seconds then switch it back on.
Remove the collector, ensure that it is empty, wait for 6 seconds and fit it
back in place.
Check that the collector is pushed in correctly.
Remove the drawer, wait for 6 seconds and fit it back in place.
Check that the cleaning drawer is pushed in correctly.
The appliance resets itself automatically when the power is switched back
on and is ready for a new cycle.
The drip tray has overflowed: empty it and clean the cleaning drawer.
Check that the drip tray is fitted correctly.
Unplug the appliance for 20 seconds, remove the Claris cartridge and if
required, put it back into service.
If the fault persists, note the fault number and contact KRUPS' Customer
Service.
13