Table of Contents
Advertisement
Advertisement
Table of Contents
Related Manuals for Nilfisk-Advance MH 4M Series
Summary of Contents for Nilfisk-Advance MH 4M Series
- Page 1 MH 4M - Instructions for use 107140469 F (03. 2015)
-
Page 3: Table Of Contents
Contents 1 Safety instructions ........................... 2 2 Description ............................2 Purpose ........................... 2 Operating elements ......................... 2 3 Before starting the cleaner ......................3 Setting up the cleaner ......................3 Set the brake ........................... 3 Install Crank handle for high pressure hose reel .............. -
Page 4: Safety Instructions
1 Safety instructions High Pressure Washer - SAFETY INSTRUCTIONS 107141898 D (09-2015) 2 Description Purpose This high-pressure cleaner has Chapter 5 describes the use of been designed for professional the high-pressure cleaner for use. It can be used for cleaning various cleaning jobs. -
Page 5: Before Starting The Cleaner
3 Before starting the cleaner Setting up the cleaner Every fuel-burning appliance, formance before it left our fac- such as pressure washers, de- tory. The factory is located at ap- pends upon a proper mix of fuel proximately 120m (390 ft) above and air (by weight) for proper sea level, and the combustion... -
Page 6: Install Crank Handle For High Pressure Hose Reel 1)
Install Crank handle 1. Pull cap of crank in arrow di- for high pressure hose rection. 2. Align tabs on crank with slot reel in axle. 3. Put crank on axle of high pressure hose reel. 4. Fix crank by pushing the cap. Fit clamp for high- Insert clamp into the ø... -
Page 7: Antiscale
Antiscale The Nilfisk Antiscale dosing sys- Use the schematic to find the tem is set by the factory. right dosage of No Scale/anti To adjust the water hardness we stone and water, and add the recommend that the inlet water mixture to the antiscale tank. -
Page 8: Connecting The Water Supply
1. Rinse the water supply hose 3.10 Connecting the water briefly in order to prevent supply sand an other dirt particles entering into the machine. 2. Connect water supply hose to the machine. 3. Open water tap. NOTE! See chapter 9.4 Technical Data for required quantity of water and water pressure. -
Page 9: Control / Operation
4 Control / Operation Connections 1. Pull the blue quick-release 4.1.1 Connecting the spray grip (A) of the spray gun lance to the spray gun backwards. 2. Insert the nipple of the spray lance (B) into the quick- release connection and re- lease it. -
Page 10: Pressure Regulation (Tornado Lance)
Pressure regulation 1. Turn the twist grip on the (Tornado Lance) spray unit: – High pressure = clockwise (+) for high pres- sure – Low pressure = anticlockwise (–) for low pres- sure. Pressure regulation 1. Turn the twist grip on the (VarioPress Gun) spray unit: For safety reasons, never tie back... -
Page 11: Some Typical Cleaning Tasks
Encrusted or thick layers of dirt can be loosened or softened up by 5.1.1 Soaking a period of soaking. This is for example an ideal method within ag- riculture – for example, within pig sties. The ideal soaking method can be achieved via use of foam or simple alkaline detergent. Let the product lie on the dirty surfaces for around 30 minutes before pressure washing. - Page 12 5.2.2 Vehicle Task Accessories Method Vehicle bodywork Standard lance 1. Apply detergent to vehicle or equipment surfaces in Detergent injection order to soften up dirt and grime. Apply from bottom Curved lances and un- to top. In cases of particularly dirty vehicles, pre-spray derchassis washers with a product such as Allosil in order to remove traces brushes...
-
Page 13: After Using The Cleaner
6 After using the cleaner Switching off the 1. Turn the main switch to posi- tion „OFF“. cleaner 2. Close water tap. 3. Squeeze the spray gun han- dle until the cleaner is de- pressurised. 4. Lock the safety catch on the spray gun. -
Page 14: Maintenance
7 Maintenance Maintenance plan Every six After the fi rst 50 months or Weekly operating hours 500 operating required hours 7.2.1 Water fi lters 7.2.2 Fuel fi lter 7.2.3 Checking the pump oil quality 7.2.4 Changing the pump oil ... - Page 15 7.2.3 Checking the pump oil 1. Check colour of pump oil. If the oil has a grey or white quality shade, change the oil (see chapter 7.2.4) 2. Top up cold pump with fresh oil if necessary. Oil type see chapter 9.4 Technical Data.
-
Page 16: Troubleshooting
8 Troubleshooting Indications on Display Indication lights Cause Remedy > Constant light - The appliance is ready for operation When switching on, all the LEDs light up once before the motor is switched on > Flashing light > Contact Nilfi sk Service - Flow sensor fault Cold water operation possible - Water tap closed or water... -
Page 17: Other Faults
> Flashing light (alternately) > • Turn main switch in position - Motor overheated “OFF“, let the machine cool down • Remove/disconnect exten- sion cable • Possible phase failure; have electrical connection checked > - Machine overheated > Contact Nilfi sk Service >... -
Page 18: Guarantee
Guarantee general conditions Machines being misused. business are applicable with Machines being repaired or regard to the guarantee. tampered with by unauthor- Unauthorised modifications ized person(s). to the appliance, the use of The use of parts other than incorrect accessories, spare Nilfisk Cleaning Systems, parts and cleaning chemicals in... -
Page 19: Technical Data
Technical Data 4M-190/960 4M-190/960 4M-200/1010 MH 4M Descr. 140/560 X 165/820 X 180/860 L 180/860 X 170/890 170/890 4M-190/960 X 4M-190/960 X 4M-200/1010 X 200/1010 Voltage 200 V / 3~ / 50Hz Voltage 200 V / 3~ / 60Hz Voltage 220 V / 1~ / 60Hz Voltage 230 V / 1~ / 50Hz Voltage 230 V / 1~ / 60Hz Voltage 240 V / 1~ / 50Hz... - Page 20 PERU HEAD QUARTER GERMANY TURKEY Nilfi sk S.A.C. Nilfi sk GmbH Nilfi sk A.S. DENMARK Calle Boulevard 162, Of. 703, Lima 33- Guido-Oberdorfer-Straße 2-10 Serifali Mh. Bayraktar Bulv. Sehit Sk. No:7 Nilfi sk A/S Perú 89287 Bellenberg Ümraniye, 34775 Istanbul Kornmarksvej 1 Lima Tel.: +90 216 466 94 94...