Radio Operation 遙控器操作 7; Binding Process 安全校頻配對 7 - THUNDER TIGER Sparrowhawk XXT Instruction Manual

5
RADIO OPERATION 遙控器操作
a
a. When turning radio system on. Turn the transmitter on first, then turn on the ESC.
b. When turning the radio system off. Turn the ESC off first, then turn off the transmitter.
c. Reversing servos. Enter the NORM and REV mode by pressing the "up" and "down" keys.
Caution: Do not run the transmitter's battery flat or you will lose control of the car. For additional details, please refer to
the transmitter instruction manual.
a. 為避免車子失控暴衝，先開啟發射機電源。
b. 接著開啟速控器電源。電源的關閉則是相反的順序，先關速控器電源，再關發射機電源。
c. 伺服機的正逆轉調整功能是用來控制伺服機與發射機控制是否一致？進入圖中之顯示之發射機LCD顯示屏幕上之調整模式，按壓"up"(+)
或 "down"(-)按鈕可變換伺服及轉動方向為 "NOR"(正常) 或 "REV"(反轉)。此調整功能可針對不同之伺服機進行調整(方向、油門
或預備頻道)。其他注意事項請參考發射機說明書。
6
BINDING PROCESS 安全校頻配對
a
d
LED: GREEN 綠
A binding feature is included in the ACE RC Cougar 2.4GHz spread spectrum system to ensure the transmitter and receiver bind
properly and prevent interference from other controllers. With the Ready-To-Run package, full binding procedure has been completed
at the factory prior to shipping. To manually bind Tx/Rx, please proceed as per the following steps:
a. Press and hold the "Binding SW button on the back side of the transmitter while turning on the transmitter.
b. Release the "Binding SW* button after the green LED flashes indicating the transmitter is binding.
c. Press and hold the bind button on the receiver while turning on the receiver. Binding process will then start automatically.
d. Successful binding is confirmed by the blinking LED turning to constant on the transmitter. The LED on the receiver turns greens.
Once binding is complete, the system automatically connects.
Note: Binding prrocess may take 3~10 seconds to execute. If binding fails, the LED on the receiver will turn red. Please turn
off the power and repeat steps a~d.
ACE RC Cougar PS3i 採用最先進的專用3動2.4GHz無限展頻遙控系統。這個系統結合發射與接收可以互動溝通模式，跳動式頻道搜
尋，使得整體無線遙控系統的傳輸展現精準穩定的特性同時也無須擔心頻率干擾的問題。本完成車搭配預先校頻配對好之遙控系統，
無須再調整即可進行操作。如發現無法操控情形發生，需要重新校頻配對，請依照下列步驟重新進行校頻配對程序：
a. 打開發射機電源時，同時持續按壓發射機背面之 "Binding SW" 按鈕。
b. 直到按鈕旁之LED綠燈快速閃爍，再放開 "Binding SW" 按鈕，表示發射機正在進行自動搜尋校頻，此時請不要關閉發射機電源。
c. 然後按壓接收機上之 "Binding SW" 按鈕並同時開啟接收機電源，此時接收機將自動進行校頻配對程序。
d. 一旦完成配對程序，發射機LED燈號會從綠色快速閃爍轉換成持續綠色燈號，接收機LED燈號將從紅色轉換為綠色並持續慢速閃爍。
此時表示接收積與發射機以完成配對溝通，可以進行操控。
注意：遙控系統校頻配對可能需要3~10秒執行程序。如果程序執行錯誤，發射及接收模組的LED燈號將持續呈現紅色。請關閉電源再依a
~d的順序重新操作配對程序。
b
關 OFF
b
按
LED: GREEN FLASH
綠燈閃爍
c
ON 開
c
LED: RED 紅
按
Switch on Power
開啟電源