THUNDER TIGER Sparrowhawk XXT Instruction Manual page 7

1. Transmitter Antenna: Straighten up the antenna before operating the model.
2. Power Indicator: The LED light indicates power is "on" or "off".
3. Edit Buttons: The Left and Right buttons are the "functions" selecting keys. The up (+) and down (-) buttons are the keys for adjusting
values . Toggle between functions by pressing the "Edit Buttons" (left and right keys) and adjust settings with the up and down keys.
4. LCD Display: The Cougar transmitter features an "Easy-to-Read" LCD Display. Battery status, functions and settings are all clearly displayed
on the screen.
5. Digital Steering Trim lever: Push this lever left or right to adjust the center point on the steering servo. A cursor on the LCD screen's top
ruler indicates current Steering Trim adjustments. Steering Trim adjustments ensure the model runs straight.
6. Digital Throttle Trim lever: Push this lever up or down to adjust the center point on the throttle/brake servo. A cursor on the LCD screen's
left ruler indicates current Throttle Trim adjustments. Throttle Trim adjustments set the braking amount for "Drag Brake" and "Coast Brake".
NOTE: The Digital Throttle Trim function adjusts neutral point without affecting maximum throttle servo travel and full-throttle
position.
The Digital Steering Trim function adjusts maximum steering servo travel for both left and right steering. If adjustments are incorrect,
steering linkage binding or damages to the steering servo may occur.
7. Digital Steering D/R(Dual Rate) lever: Push this lever left or right to adjust the amount of steering dual rate. Right to increase dual rate,
left to decrease dual rate.
8. AUX Ch Button: Additional control function for the model.
9. External Charging Jack: For recharging the transmitter battery (only use a rechargeable NiCd/NiMH battery pack.)
10. 2.4GHz TX RF Module and binding SW: The Binding SW button is located on the 2.4GHz TX RF module unit.
11. Steering Wheel: Controls steering of the model.
12. Power Switch: Slide the switch to turn the transmitter on or off. The "DISPLAY" position provides direct access to the transmitter's edit
buttons and trim levers without causing frequency interferences to other transmitters. Do not attempt to drive the model under the "DISPLAY"
mode.
13. Throttle Trigger: Pull or push to control speed and forward / backward motion.
14. Steering Tension Adjustment: Use a Phillip type screwdriver to tighten or loosen the tension of the steering wheel.
15. Battery Cover: Slide cover to install or remove batteries.
1. 天線：操作發射機時請將發射機天線扳直。
2. 電源指示燈：LED顯示燈號顯示開關機狀態，紅色燈號為開機，關機或展示狀態則無燈號。
3. 選單按鈕：選單左（<）右鈕（>）可移動功能選項，上，選單上(+)下(-)鈕可調整功能選項之設定值。
4. 選單屏幕：功能選項為方便閱讀及操作，採直接印刷於LCD顯示屏幕上，無須按鈕進入即可一目了然。
5. 轉向微調撥桿：左右撥動轉向微調撥桿可調整轉向伺服機中立點。調整時LCD顯示屏幕上之ST游標卡尺會隨著調整量大小移動游標標示點位
置，基本上此調整撥桿為保持遙控模型之直線性。
6. 油門微調撥桿：左右撥動油門微調撥桿可調整轉向油門伺服機中立點。調整時LCD顯示屏幕上之TH游標卡尺會隨著調整量大小移動游標標示
點位置，基本上此調整撥桿為設定遙控模型之"中立點煞車"及"行進煞車"之行程量。
調整油門微調撥桿時，油門伺服機之全行程兩端定位點將不會因為中立點位置改變因此而移動位置，此調整將僅進行油門中立點之調整。調
整轉向微調撥桿時，轉向伺服機之全行程兩端定位點將因為中立點的改變而做相對位置移動。因此在調整轉向微調撥桿時需注意行程動作是
否因為機械結構之限制而造成可能之轉向控制系統發生干涉情形甚至損害伺服機本身。
7. 轉向角度大小調整鈕：調整此按鈕可調整轉向角度大小。向右按壓此鈕可增加轉向大小行程量，向左則為減少。
8. 預備頻道切換鈕：本遙控系統提供額外擴充之伺服機之控制頻道。按壓此控制鈕可控制此動作之開啟與關閉。
9. 充電器接座：請使用鎳氫或鎳鎘專用充電電池及充電器。
10. 2.4GHz發射模組及校頻配對設定鈕：發射機採用固定式2.4GHz發射模組，模組上之BINDING SW校頻配對設定鈕為配對發射/接收頻率之用。
11. 轉向舵輪：控制遙控模型之左右轉向。
12. 電源開關：介於發射機電源"開啟"與"關閉"模式間，可以選擇"調整顯示"模式，選擇此模式發射機將不會傳送操控訊號以方便選手在
賽場上的調整以預防可能之頻率干擾。此模式發射機將無法操控遙控模型。
13. 油門扳機：推拉油門扳機控制遙控模型的前後及煞車動作
14. 轉向舵輪調整螺絲：使用小型十字起子調整此調整螺絲來改變轉向舵輪旋轉鬆緊度。
15. 電池護蓋：推移電池護蓋即可取出電池進行更換。