A. Arm bed and its accessories Part No. Name 1 Needle 2 Needle 7.02.01.068 Arm bed 7.02.21.467 Back cover(1) Back cover(2) 7.02.15.096 Back cover screw 7.02.11.482 Lower plate 7.02.15.044 Lower plate screw 7.02.11.483 Safety guard cover 7.02.15.964 Safety guard cover screw 7.02.11.484 Fixed plate 7.02.15.444...
B.Presser bar parts Part No. Name 1 Needle 2 Needle 7.02.05.01101 Presser foot lifting lever 7.02.15.056 Set screw 7.02.15.049 Screw 7.02.15.057 Set screw 7.02.15.025 Screw 7.02.08.032 Bushing(Upper) 7.02.08.033 Bushing(Lower) 7.02.03.009 Guide rail bar 7.02.08.007 Presser bar position bracket 7.02.15.050 Screw 7.02.03.420 Presser bar lifter shaft 7.02.15.061...
G.Presser foot lifting parts Part No. Name 1 Needle 2 Needle 7.02.15.959 Adjusting screw 7.02.17.007 Elastic presser plate 7.02.15.791 Spring presser plate supporting screw 7.02.18.039 Split retaining ring 7.02.15.020 Set screw 7.02.15.067 7.02.17.410 Knee lifting lever connecting rod 7.02.18.031 Split retaining ring 7.02.06.004 Upper and lower transport arm 7.02.15.053...
J.Clutch set parts Part No. Name 1 Needle 2 Needle 7.02.09.079 Shaft washer 7.02.15.056 Screw 7.02.03.013 Lower shaft(Left) 7.02.03.012 Lower shaft(Right) 7.02.01.354 Safety clutch assy. Coupling(Left) Position screw Set screw Connecting plate Elastic stop ring Coupling(Right) Ball Spring Set screw 5-10 Clutch seat 5-11...
R.Thread trimming driving parts Part No. Name 1 Needle 2 Needle 7.02.01.286 Thread trimming vibrating lever assy. 7.02.03.341 Thread trimming vibrating lever shaft 7.02.10.367 Connecting lever pin (Right) 7.02.15.056 Connecting link pin set screw 7.02.05.364 Thread trimming connecting link 7.02.17.351 Connecting link spring 7.02.10.369 Connecting link pin (Left)
U.Lower feed and backstitch parts for single needle Part No. Name 1 Needle 2 Needle 7.02.19.348 Needle bar vibrating switch solenoid 7.02.10.460 Solenoid joint 7.02.15.555 Solenoid screw 7.02.18.071 Washer 7.02.11.501 Solenoid fixed plate 7.02.15.803 Fixed plate screw 7.02.11.502 Spring fixed plate 7.02.17.138 Spring 7.02.09.118...
Page 105
o er eed a d ba st t h parts or s le eedle...
X. Parts of integrated machine Part No. Name 1 Needle 2 Needle 7.02.01.072 Machine case 7.02.16.430 Oil box Assy. 7.02.15.975 Oil box screw 7.02.16.431 Back over (Upper) 7.02.16.432 Back over (Lower) 7.02.15.058 Screw 7.02.15.997 Screw 7.02.19.359 Motor 7.02.09.120 Stitch length indicating ring 7.02.09.121 Stitch length indicating ring 7.02.07.280...
Page 115
EC - Manufacturer Declaration EC Declaration of Conformity EG Konformitätserklärung We declare herewith that the following equipment: Hiermit erklären wir, dass die Bauart des Nähmaschinenantriebes: NEEDLE POSITIONER MOTOR TYP AC SERVO MOTOR---i SERIES AC SERVO MOTOR---i SERIES AC SERVO MOTOR---G SERIES AC SERVO MOTOR---G SERIES AC SERVO MOTOR---GD SERIES AC SERVO MOTOR---GD SERIES...
Page 116
Declaration of Conformity for Concentration Limits for Certain Hazardous Substances We declare herewith that the following AC servo motor series products list below : AC Servo Motor --- i Series / G Series / GD Series / MD Series Devrice---TK Series / TC Series / MK Series / MC Series Are complies with the following directives and requirements : 1.
Page 117
Content Safety instruction....................1 Wiring & earthing ....................4 III. Function description for standby ...............5 Multi-function description .................8 Parameter selection description................9 Parameter value description................10 VII. Parameter table………………………………………...…………………11 VIII. ………………………………………………………..……………………14 Point code & Error code……………………………….....…………15...
I. Safety instruction User are asked to read this operation manual completely and carefully before installation 。 or operation When install and operate TF control box, precaution must be taken as the following. This product is designed for specify sewing machines and must not be used for other purposes. Work Environment (1).
Page 119
(3). Power cord: a. Avoid power cord being applied by heavy objects or excessive force, or over bend. b. Power cord must not set to be near the V-belt and the pulley, keep 3 cm space or above. c. Check the outlet voltage before plugging the cord, make sure it match the voltage shown on the name plate of the Feeder in ±10 % ranges.
Page 120
1.4 Safety in Maintenance and Repairs : Power must be turned off first, when (1). Uninstall the motor or the control box, or plug and unplug any connector. (2). Turn off the power and wait 10 minutes before opening box cover. (3).
Page 121
II. Power Connection and Grounding (1). Single phase and three phase connection : Green/yellow wire is the ground wire Brown wire Blue wire PVC Cable Single Phase Green / Yellow wire Brown If use on single phase Black (220 V), don’t connect the black wire.
III. Function description at standby ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ Slow start Motor run at slow speed when sewn start. ○ Parameter setting Press key and hold 2 second to enter parameter setting mode, set value you need after entered.
Page 123
○ Value adjustment = Increment / = Decreasing ○ Bar tacking Press key, led light up, bar tacking be performed, ABC maximum 15 stitches, D maximum 15 times . ○ Presser foot lifting automatically selection after trimmed. Press key to perform this function. ○...
Page 124
○ Multi function You can choose, thread clamp, wiper, needle up/down, slow start, needle raising, counter through this key. ○ Start tacking Press key to perform function, , adjust stitch of AB step, maximum 15 stitches each step. ○ Needle up/down selection Needle up/down selection when motor stopped.
IV. Multi-function Press S at standby 2 seconds to change to multi-function. ○ ○ ○ ○ F Multi-function Press to perform/close function. ○ Return to standby ○ F Selection key for multi-function Select F0 ~ F6 function. No function Thread clamp Wiper Needle up/Down SLOW...
V. Parameter selection Press P 2 seconds to change to parameter selection. ○ ○ ○ ○ ○ P Key Increment of parameter. ○ Start tacking Decreasing of parameter. ○ S Key Enter parameter value mode. ○ End tacking Parameter decreasing.
Page 127
VI. Parameter value setting Press S at parameter selection mode to change to parameter value setting mode. ○ ○ ○ ○ ○ ○ P Key Return to parameter selection mode, parameter increment. ○ Start tacking Return to parameter selection mode, parameter increment. ○...
○ Value adjustment = Increment = Decreasing You must press S key to save adjusted value VII. Parameter table Function Code Range Description ( spm ) Maximum speed adjustment 50~9999 001. H Maximum sewing speed ( spm ) Start tacking speed 50~ 8000 Start tacking speed 004.
Page 129
: Perform end tacking when constant stitch be performed at last step Correction can not be perform Perform end tacking automatically when constant stitch OFF : : Cannot perform end tacking when constant stitch be performed at performed ON / OFF 010.
Page 130
( spm )Trimming speed 50~500 Trimming speed adjustment 061. T 0~990 064. FO ( ms ) Presser foot lifting full on time setting Presser foot lifter output duty circle to avoid Duty circle for presser 10~90 065. FC getting heat foot lifting Motor start delay time to Pedal toe down motor delay to start ,...
Page 131
VIII. Operation precaution pleases check JP1 must at 0V before power ON. Pleases reboot if touches panel, PIN electronic components or circuit when power ON. Do not touch panel, PIN electronic components or circuit. Do not press to hard or used sharp article when operates panel. Only uses finger to operate touch panel.
IX. Point code & error code Error Cause Description code Motor connector connect un-properly. ER0. 7 Power shut down. Pleases check motor or connector is normal or Synchronizer out of order. 3. Sewing machine locked or belt stuck by abnormal. article.