Subscribe to Our Youtube Channel
Related Manuals for MSA Ultra Elite-H
Summary of Contents for MSA Ultra Elite-H
- Page 1 Operating Manual Ultra Elite-H Mask – Negative Pressure Mask/Helmet Combination Ultra Elite-H/F1 Order No.: 10110561/03 MSAsafety.com...
- Page 2 MSA Europe GmbH Schlüsselstrasse 12 8645 Rapperswil-Jona Switzerland info.ch@MSAsafety.com www.MSAsafety.com © MSA 2018 All rights reserved...
-
Page 3: Table Of Contents
Safekeeping and Storage ........17 Ultra Elite-H Mask – Negative Pressure... - Page 4 Applicable Helmets ......... . 20 MSA Gallet F1 Helmets ........20 MSA Gallet F2 X-TREM Helmets .
-
Page 5: Safety Regulations
Before use the product operability must be verified. The product must not be used if the function test is unsuccessful, it is damaged, a competent servicing/maintenance has not been made, genuine MSA spare parts have not been used. -
Page 6: Liability Information
MSA or authorized persons. Liability Information MSA accepts no liability in cases where the product has been used inappropriately or not as intended. The selection and use of the product are the exclusive responsibility of the individual operator. -
Page 7: Description
[thus keeping the lens largely fog-free] and then through the check valves into the nose cup. The exhalation air passes through the exhalation valve directly to the ambient air. Fig. 1 Overview mask/helmet combination Helmet Visor Adapter with tightening strap Helmet Connector with inhalation and exhalation valves Lens Ultra Elite-H Mask – Negative Pressure... -
Page 8: Mask Versions
Part Number Marking [date code, serial number] CE-marking with notified body number [DEKRA EXAM, Zertifizierungsstelle Dinnendahlstr. 9, 44809 Bochum] X: ATEX classification A, B or C according to the Lens typ. EN standard, class Ultra Elite-H Mask – Negative Pressure... -
Page 9: Certification
DIN 58610:2006 for helmets see operating manual helmet 0158 DEKRA EXAM GmbH, Dinnendahlstr. 9, 44809 Bochum, Germany, Notified body number: 0158 The Declaration of Conformity can be found under the following link: https://MSAsafety.com/DoC Ultra Elite-H Mask – Negative Pressure... -
Page 10: Use
Adjust the helmet according to the helmet’s operating manual. Grip the helmet with both hands with the chinstrap open. Pull the helmet from the forehead over the head. Close and slightly tighten the chin strap. Ultra Elite-H Mask – Negative Pressure... -
Page 11: Donning The Mask
Donning the Mask WARNING! In order to guarantee a proper fit for those wearing glasses, the Ultra Elite-H Mask spectacle kit must be worn since ordinary glasses cannot be worn under the mask. When fitting the mask in position the chin strap of the helmet must be loose. Remove chin piece if necessary. -
Page 12: Leak Check
Lift both hooks of the helmet adapter to the side and pull them back out of the helmet slots. Remove the mask to the front. Do not grip the mask by the exhalation valve! Remove the helmet. Ultra Elite-H Mask – Negative Pressure... -
Page 13: Cleaning, Disinfection
After cleaning check the two screws for the lens ring. Retighten the screws hand-tight if neces- sary. Cleaning/Disinfection with an Ultrasonic Cleaner When cleaning/disinfecting with an ultrasonic cleaner please follow the cleaning agent’s user instructions on this CD/DVD. Ultra Elite-H Mask – Negative Pressure... -
Page 14: Cleaning By Hand
Disinfect the mask using recommended disinfectant. Please observe the user instruction for the disinfectant. Thoroughly rinse mask in running water. Dry mask and components and reassemble mask in reverse order. Perform a tightness test (see chapter 5.5). Ultra Elite-H Mask – Negative Pressure... -
Page 15: Maintenance
Always use original parts from MSA. Repairs and maintenance must be carried out only by authorised service centres or by MSA. Changes to devices or components are not permitted and will result in loss of approval. -
Page 16: Maintenance Of The Exhalation Valve
Perform a tightness test [ chapter 5.5]. Tightness Test of the Mask The testing of the masks for tightness is performed using an applicable MSA test device in accordance with the relevant operating manual. Fit mask tight onto the test device. -
Page 17: Visual Test And Function Test
For the safekeeping of the mask the mask container should be used. This also applies to masks with installed filters, except CO and NO filters. MSA rubber products are protected by an anti-aging agent that can become visible as a light coating. This coating is harmless and can be removed during cleaning. -
Page 18: Ordering Information
Inhalation valve seat Elite Nose cup [without valves] Inhalation valve disc Carrying strap Lens ring Speech diaphragm ring Adapter with tightening strap Speech diaphragm Screw for lens ring Exhalation valve disc Elite Lens Clamp Elite Face blank Ultra Elite-H Mask – Negative Pressure... -
Page 19: Mask
D2056733 Special tool [for replacing exhalation valve and speech diaphragm] D2055038 Exhalation valve closure D2056703 Mask hanger [package of 4] D2055753 Mask tightness test kit [for more MSA testing instruments refer to D6063705 www.MSAsafety.com] Advantage container 10026179 Test plate D6125721... -
Page 20: Applicable Helmets
* comply with directive: vfdb-Richtlinie 0802:04 Helmets Colour of the shell Gallet F1 XF [EN 443:2008] size M, L all colours Neck curtain: aluminium wool (integral) nomex Lamp: Lamp holder (mounted, spare) Integrated light module Retro-reflective stickers: Grey Ultra Elite-H Mask – Negative Pressure... -
Page 21: Msa Gallet F2 X-Trem Helmets
TRAFFIC RESCUE [directive 89/686/EC] -unvented shell -3 point chinstrap GA35xx White Blue Yellow Black Orange Photoluminescent Optional: Wool neck curtain (GA3240) Retro-reflective stickers (GA3230): silver, yellow, red, blue or green Ultra Elite-H Mask – Negative Pressure... - Page 22 For local MSA contacts, please visit us at MSAsafety.com Because every life has a purpose...
Need help?
Do you have a question about the Ultra Elite-H and is the answer not in the manual?
Questions and answers