Start-Up Wizard Guide - Honeywell CORE Drive Quick Start Manual

START-UP WIZARD GUIDE

Screen Screen
# Verbiage
1 Boot Honeywell displayed for 3 seconds
Screen
2 Selection Choose how to interact with the VFD:
Screen Recommendation: Press function key F4 to
start the wizard
3 Select Choose the keypad programming language
Language Use UP and DOWN arrows to change from
default. Press ENTER to accept change.
F1 BACK up one menu (SAME function
throughout WIZARD)
F4 Next Parameter (SAME function
throughout WIZARD)
4 Clock Time Select the time (Military) HH:MM:SS and date
and DATE YY/MM/DD
5 Motor Motor's rated voltage based upon Motor
Voltage Name Plate data
6 Motor Motor's rated current in FLA, Full Load AMPs
Current based upon Motor Name Plate data. Do not
use motor service factor amperage for this
value.
7 Motor Motor's rated frequency based upon Motor
FREQ Name Plate data
8 Motor RPM Motor's rated RPM based upon Motor Name
Plate data
9 ACCEL The time required to accelerate from the
TIME motor's current speed reference to a new
speed reference
10 DECEL The time required to decelerate from the
TIME motor's current speed reference to a new
speed reference
11, 12, PRESET Present Speed options. On digital input
13 SPEED closure the VFD will ignore the speed
1,2,3 reference from the analog input and will run at
the programmed speed.
14 Analog Select the speed reference signal type.
Input
15 MIN The minimum frequency at which the motor
Frequency will operate
16 MAX The maximum frequency at which the motor
Frequency will operate
17 PRESS F4 Saves all parameter updates - VFD is ready
to SAVE to operate
ALL
Table 11. Honeywell Commissioning Start-Up Wizard
Screen Description
N/A
F4: Initials the START UP WIZARD
Menu: redirects to MAIN MENU
ESC: redirects to MONITOR Screen
1. English
2. Spanish
3. Chinese
4. Portuguese
5. French
Use arrow keys to adjust. Press ENTER to save
changes, F4 to advance without changes.
Press F4 to accept factory defaults. Use arrow keys to
adjust ONLY if needed. PRESS ENTER to save
changes.
Press F4 to accept factory defaults. Use arrow keys to
adjust ONLY if needed. PRESS ENTER to save
changes.
Press F4 to accept factory defaults. Use arrow keys to
adjust ONLY if needed. PRESS ENTER to save
changes.
Press F4 to accept factory defaults. Use arrow keys to
adjust ONLY if needed. PRESS ENTER to save
changes.
Press F4 to accept factory defaults. Use arrow keys to
adjust ONLY if needed. PRESS ENTER to save
changes.
Acceleration time is factory set for typical Fan and
Pump needs. Use arrow keys to adjust. Press ENTER
to save changes, F4 to advance without changes.
Decceleration time is factory set for typical Fan and
Pump needs. Use arrow keys to adjust. Press ENTER
to save changes, F4 to advance without changes.
With the use of MFI (Multifunction inputs) 1, 2, or 3 the
drive can be sent to the programmed speed on digital
input closure (Usage not required in the field). Adjust as
needed or press F4 to accept factory defaults.
0. 0-10V - Use AVI (Analog Voltage Input terminal)
1. 4-20mA - Use ACI (Analog current input terminals)
2. 2-10V - Use AVI
3. 0-20mA - Use ACI
Press F4 to accept factory defaults. Use arrow keys to
adjust ONLY if needed. PRESS ENTER to save
changes.
Press F4 to accept factory defaults. Use arrow keys to
adjust ONLY if needed. PRESS ENTER to save
changes.
F1 will escape the user back to the Selection Screen
again
F4 will save parameters and take the user to the display
screen
17
HONEYWELL CORE DRIVE
Screen options
62-0410—04