Satel AOD-210 Manual
Wireless outdoor dual technology motion detector
Hide thumbs
Also See for AOD-210:
- Quick installation manual (2 pages) ,
- Quick installation manual (2 pages)
Related Manuals for Satel AOD-210
Summary of Contents for Satel AOD-210
- Page 1 AOD-210 Wireless outdoor dual technology motion detector Firmware version 1.00 aod-210_en 03/19 SATEL sp. z o.o. • ul. Budowlanych 66 • 80-298 Gdańsk • POLAND tel. +48 58 320 94 00 www.satel.eu...
- Page 2 Rating plate of the device can be found on the rear side of the electronics module. SATEL aims to continually improve the quality of its products, which may result in changes in their technical specifications and software. Current information about the changes being introduced is available on our website.
- Page 3 The AOD-210 outdoor detector can detect motion in a protected area. It is designed for operation within the ABAX 2 / ABAX two-way wireless system. This manual applies to the detector with firmware version 1.00 (or newer), which is supported by: ...
- Page 4 AOD-210 SATEL Radio communication The detector connects to the controller / control panel at regular time intervals to provide information about its state (periodical communication). Additional communication may take place as a result of alarm (see “Operating modes”). Alarms The detector will report alarm: ...
- Page 5 SATEL AOD-210 Light intensity Detection threshold Turning on [P Turning off [P 5 lx 10 lx 10 lx 20 lx 30 lx 50 lx 40 lx 70 lx Table 1 Test mode The test mode makes the detector testing easier, because the LED indicators are enabled and the dusk sensor reacts quicker to changes in the light intensity.
-
Page 6: Selecting A Mounting Location
AOD-210 SATEL In response to the battery voltage drop below 2.75 V, sensitivity of sensors in the detector is automatically lowered to eliminate false alarms. Electronics module Do not remove the plastic cover from the circuit board to prevent damage to the components located on the board. -
Page 7: Installation
SATEL AOD-210 4 Installation There is a danger of battery explosion when using a different battery than recommended by the manufacturer, or handling the battery improperly. Be particularly careful during installation and replacement of the battery. The manufacturer is not liable for the consequences of incorrect installation of the battery. - Page 8 AOD-210 SATEL 4. Replace the cover. 5. Put the detector at the place of its future installation. 6. Check the level of signal received from the detector by the ABAX 2 / ABAX controller or the INTEGRA 128-WRL control panel. If the signal level is lower than 40%, select another place for installation.
- Page 9 SATEL AOD-210 11. Fasten the electronics module in the enclosure. 12. If you have mounted the detector on a bracket, connect an additional tamper switch to the TMP terminals (black wire to one terminal, blue wire to the other) and remove the jumper from the pins.
-
Page 10: Ball Bracket Mounting
AOD-210 SATEL 4.2 Ball bracket mounting 1. Attach extra tamper switch: – screw the holder to the tamper switch (Fig. 8-I), – put the unit making the surface bigger on the tamper switch (Fig. 8-II), – screw the tamper unit to the ball bracket (Fig. 8-IV). - Page 11 SATEL AOD-210...
-
Page 12: Specifications
AOD-210 SATEL 5 Specifications Operating frequency band..............868.0 MHz ÷ 868.6 MHz Radio communication range (in open area) ABAX 2 ACU-220 ....................up to 2000 m ACU-280 ....................up to 1600 m ABAX ......................up to 500 m Battery........................CR123A 3 V Battery life expectancy .................. - Page 13 SATEL AOD-210 Maximum humidity ......................93±3% IP code..........................IP54 Dimensions ....................65 x 138 x 58 mm Weight..........................182 g...
Need help?
Do you have a question about the AOD-210 and is the answer not in the manual?
Questions and answers