Table of Contents
Advertisement
Quick Links
New Mechanism Designs
With auto-stop feature based
on human touch
LP Connect
Bridge
™
Allows chair to communicate
via Wi-Fi or other protocols
LPConnect
Installation
™
Occupancy Detection System
Allows auto-close and other features
based on exit occupancy status
USER GUIDE
Customizable Smart
Interface/Buttons
Re-assignable buttons to fit different
configuration needs
LP Drive Motor
Latest technology with
hall sensors
LP Connect Smart Motor Controller
Allows better end-user experience and
custom control of motor
Advertisement
Table of Contents
Subscribe to Our Youtube Channel
Related Manuals for Leggett & Platt LPConnect
Summary of Contents for Leggett & Platt LPConnect
- Page 1 USER GUIDE LPConnect Installation ™ Occupancy Detection System Allows auto-close and other features based on exit occupancy status Customizable Smart Interface/Buttons Re-assignable buttons to fit different configuration needs New Mechanism Designs With auto-stop feature based on human touch LP Drive Motor...
-
Page 3: Table Of Contents
CONTENTS IMPORTANT SAFETY INSTRUCTIONS ............1 Installation ....................2 Step 1: Verify Hardware ................2 Tools Required ..................4 Assumptions ..................... 4 Step 2: Attach Motor Controller ..............5 Step 3: Attach LP Sense Ring Terminal ............5 Step 4: Attach LP Connect Bridge ..............6 Step 5: Occupancy Detection Pad .............. -
Page 4: Important Safety Instructions
IMPORTANT SAFETY INSTRUCTIONS When using an electrical furnishing, basic precautions should always be followed, including: 1. Read all instructions before using this product. 2. DANGER – To reduce the risk of electric shock, always unplug this furnishing from the electrical outlet before cleaning. 3. WARNING – To reduce the risk of burns, fire, electric shock, or injury to persons, unplug from outlet before putting on or taking off parts. 4. Use this furnishing only for its intended use as described in these instructions. -
Page 5: Installation
INSTALLATION Step 1: Verify Hardware Remove hardware from shipping container and verify all contents are included. Below are major components of the system. Please contact your sales representative for specific requirements for your project and full bill of materials (BOM). Attachment hardware is not included. 6. 8 pin-8 pin DIN cable with 2 pin power injection 7. 5 pin to 8 pin with 8 pin DIN pigtail cable 5. - Page 6 INSTALLATION Ref # Image Description Details Part # 8 pin DIN to 2 pin 1M Connects power supply to 7706160001 power cable motor controller LP Drive motor LP Drive motor series is 7705360001 PMINNOVA HS 532- recommended – must 295 or similar have hall sensors LP Connect theater Smart motor controller 7706110001/ smart motor controller manages commands...
-
Page 7: Tools Required
INSTALLATION Ref # Image Description Details Part # Mechanism – InNova Contains custom bushings P/N depending series recommended to support LP Sense touch on style specified technology Mechanism requires conductive bushings Power cord LP Drive Cable that connects 7706610001 USA 1.0M power supply to main power Power supply 2 amp 2 amp power supply... -
Page 8: Step 2: Attach Motor Controller
INSTALLATION Step 2: Attach Motor Controller Attach the LP Connect’s smart motor controller to chair frame with (2) self- tapping bolts. Location is dependent on design of mechanism and chair. Suggested locations are depicted in Figure 1 below. An optional angle mounting bracket (3434490001) can be used for additional installation options (see Figure 2). Be careful not to over tighten bolts. Location: top left Location: bottom left Location: bottom right Location: top right Figure 1. -
Page 9: Step 4: Attach Lp Connect Bridge
INSTALLATION Figure 3. LP Sense ring terminal suggested location Step 4: Attach LP Connect Bridge The LP Connect bridge is necessary for one chair per row of seats. Each chair is connected into the previous chair for communication, and the LP Connect bridge is installed at the end of the row. If not installing LP Connect bridge on this chair, skip to Step 5. Attach the LP Connect bridge to the wood base of the chair with (2) 1.5” wood screws using a Phillips screwdriver. Location is dependent on design of chair. -
Page 10: Step 5: Occupancy Detection Pad
INSTALLATION Step 5: Occupancy Detection Pad If not installing Occupancy Detection Pad, skip to Step 6. Using the latest in capacitive sensing technology, the system detects when an individual enters and exits the chair. The Occupancy Detection Pad should be installed between the foam cushion layer and the fabric layer. Once installed, connect the occupancy sensor to the 2 pin connector labeled “1” on the side of the smart motor controller as shown in Figure 5. Occupancy Detection Pad: installed just under the fabric layer of the seat cushion Occupancy pad plugs... -
Page 11: Step 6: Connect Cables
INSTALLATION THE FOLLOWING STEPS CAN BE COMPLETED AT MANUFACTURING OR ONSITE. Step 6: Connect Cables In Figure 6 below, Smart Motor Controller ports and associated cabling are identified for a single chair configuration. Connector sleeves are designed for tighter fit and water tight seal. It also reduces the risk of disconnection. Port A: the chair button switch 8 pin to 8 pin DIN adapter connects into port A. -
Page 12: Multi-Set Configuration W/Power Injection Cable (Teal)
INSTALLATION THE FOLLOWING STEPS CAN BE COMPLETED AT MANUFACTURING OR ONSITE. Step 6: Connect Cables In Figure 6 below, Smart Motor Controller ports and associated cabling are identified for a single chair configuration. Connector sleeves are designed for tighter fit and water tight seal. It also reduces the risk of disconnection. Port A: the chair button switch 8 pin to 8 pin DIN adapter connects into port A. -
Page 13: Connecting Multiple Chairs
INSTALLATION Connecting Multiple Chairs Figure 7 shows the wiring for two adjacent chairs in a row. For a loveseat configuration or the first set of chairs in a row, replace the power injector cable with a direct power cable (7706160001). Connect additional chairs by repeating the pattern shown in figure 7, connecting the power injector cable for each additional set of chairs to the open socket on the button adapter cable from the previous chair. Connect the LP Connect bridge to the open socket on the button adapter cable (right) of the last chair in the row. An example of four chairs in a row is shown in figure 8. Not shown: LP Sense Standard 5-pin button 5-pin to 8-pin button occupancy pad (7706150001), adapter cable (7706190001) LP Sense ring terminal cable (7706200001) -
Page 14: Step 10: Configuration Of Chair
INSTALLATION OPTION 3: Manual configuration using end-of-line software with a single chair. An end-of-line software package will be provided to manufacturers that allows the configuration parameters to be downloaded to the motor controller. This software can also assign an ID. Please see Step 10 for more details. Step 10: Configuration of Chair The LP Connect package allows you to programmatically set soft limits, auto-close and other settings. Instructions are below. 1. An end-of-line software package will be running on a PC. This allows the configuration parameters to be downloaded to the motor controller. 2. A button will be pressed on the PC software that will download the parameters and may also run the chair through a self-test, generate a serial number, etc. The following parameters can be configured: •... -
Page 15: Operation
OPERATION Auto-Close Based on Exit (if enabled) This chair may be configured with the LP Sense Occupancy Detection System. This allows the chair to auto-close when guest exits the chair without closing the ottoman completely. LP Sense Auto-Stop Based on Touch Using the latest in capacitive sensing technology, LP is a safety-enhancement feature intended to stop the motor when human skin contact is detected on the... - Page 16 800.888.4569 HFC@leggett.com LPFurnitureComponents.com © 2018 Leggett & Platt Incorporated • FCLT1032_23425_04-18...
Need help?
Do you have a question about the LPConnect and is the answer not in the manual?
Questions and answers