Advertisement
Quick Links
This user's guide describes the characteristics, operation, and use of the INA210-215EVM evaluation
module (EVM). This EVM is designed to evaluate the performance of the
current shunt monitors in a variety of configurations. The EVM layout and design are flexible enough to
allow evaluation of a wide range of applications. This document also includes a schematic, reference
printed circuit board (PCB) layouts, and a complete bill of materials.
1
2
3
4
5
6
1
Hardware Included with the INA210-215EVM
2
Measurement with Shunt
3
Measurement without Shunt
4
TO-247 Package In R1
5
CS3 Package in R1
6
TO-126 Package in R1
7
TO-220 Package in R1
8
Radial Package in R2
9
U1 Footprint
10
U1 Populated with DIP Board
11
INA210-215EVM Schematic
12
SBOU065A - August 2008 - Revised June 2014
Submit Documentation Feedback
..................................................................................................
.................................................................................................
.....................................................................................................
..................................................................................................
.............................................................................................................
...................................................................................................
................................................................................................
.....................................................................................................
..........................................................................................................
......................................................................................................
......................................................................................................
.......................................................................................................
..................................................................................................................
..............................................................................................
..............................................................................................
.....................................................................................................
Copyright © 2008-2014, Texas Instruments Incorporated
SBOU065A - August 2008 - Revised June 2014
INA210-215EVM User's Guide
Contents
..........................................................................
List of Figures
...........................................................................
User's Guide
INA210-215
voltage output
INA210-215EVM User's Guide
2
4
6
10
11
13
3
4
5
6
6
6
6
8
9
9
11
12
1
Advertisement
Subscribe to Our Youtube Channel
Related Manuals for Texas Instruments INA210-215EVM
Summary of Contents for Texas Instruments INA210-215EVM
-
Page 1: Table Of Contents
User's Guide SBOU065A – August 2008 – Revised June 2014 INA210-215EVM User's Guide This user’s guide describes the characteristics, operation, and use of the INA210-215EVM evaluation module (EVM). This EVM is designed to evaluate the performance of the INA210-215 voltage output current shunt monitors in a variety of configurations. -
Page 2: Introduction And Overview
Evaluation of all gain options through provided device boards as well as a location to solder a test device directly onto the board The INA210-215EVM allows the user to install a shunt resistor, and then connect both the common-mode voltage and load to develop the input voltage, or omit the shunt resistor and apply a differential voltage directly to the device input. - Page 3 • Six populated test boards (INA210, INA211, INA212, INA213, INA214, INA215) If any of these items are missing or damaged, please contact the Texas Instruments Product Information Center nearest you to inquire about a replacement. SBOU065A – August 2008 – Revised June 2014...
-
Page 4: Quick Start Setup And Use
Quick Start Setup and Use Follow these procedures to set up and use the INA210-215EVM. Step 1. Insert the device board to be evaluated into the U1 location. The U1 location allows the user to either evaluate one of the provided device boards or install the test device directly on the surface-mount pads in the U1 footprint. - Page 5 This connection method allows the user to either simulate the voltage developed across a sense resistor based on a given set of system conditions, or to connect the INA210-215EVM remotely to an existing shunt already included in an example application.
-
Page 6: Ina210-215Evm Circuit
INA210-215EVM Circuit This section summarizes the INA210-215EVM components. R1 can be used for shunt resistors that have a package that may not be easily adaptable to a standard, two-terminal, through-hole footprint or to a 0603 through 1206 surface-mount footprint. Specifically, this component location was added to allow the use of TO-126, TO-220, TO-247, and four terminal inline radial packages such as the CS3 series of shunts from Ohmite. - Page 7 INA210-215EVM Circuit www.ti.com Figure 6. TO-126 Package in R1 Figure 7. TO-220 Package in R1 SBOU065A – August 2008 – Revised June 2014 INA210-215EVM User's Guide Submit Documentation Feedback Copyright © 2008–2014, Texas Instruments Incorporated...
- Page 8 0603 to 1206. Figure 8. Radial Package in R2 INA210-215EVM User's Guide SBOU065A – August 2008 – Revised June 2014 Submit Documentation Feedback Copyright © 2008–2014, Texas Instruments Incorporated...
- Page 9 J2 is used as a test port at the factory but can be used for the corresponding input and output pins, if desired. U1 is the location for the test device. Five device boards are supplied with the INA210-215EVM board. Each board is populated with one of the available device gains. This interchangeable option allows users to test the devices and determine the gain setting that is best suited for a given application.
-
Page 10: Reference Voltage Setup
Miscellaneous The REF terminal of T3 allows the user to configure the INA210-215EVM for either unidirectional or bi- directional operation Two easily accessible oscilloscope ground pads are located on the board to facilitate easier probing. -
Page 11: Ina210-215Evm Schematic And Pcb Layout
INA210-215EVM Schematic and PCB Layout NOTE: Board layouts are not to scale. These figures are intended to show how the board is laid out; they are not intended to be used for manufacturing INA210-215EVM PCBs. Schematic Figure 11 shows the schematic for the INA210-215EVM PCB. - Page 12 INA210-215EVM Schematic and PCB Layout www.ti.com PCB Layout Figure 12 illustrates the PCB layout for the INA210-215EVM. Figure 12. INA210-215EVM PCB INA210-215EVM User's Guide SBOU065A – August 2008 – Revised June 2014 Submit Documentation Feedback Copyright © 2008–2014, Texas Instruments Incorporated...
-
Page 13: Bill Of Materials
Bill of Materials www.ti.com Bill of Materials Table 2 provides the parts list for the INA210-215EVM. Table 2. Bill of Materials Count RefDes Value Description Part Number Optional/Not TO-126, TO-220, TO-247, C53 Installed Optional/Not Resistor, 0603-1206/Through-hole Installed R3, R4 0Ω... - Page 14 ADDITIONAL TERMS AND CONDITIONS, WARNINGS, RESTRICTIONS, AND DISCLAIMERS FOR EVALUATION MODULES Texas Instruments Incorporated (TI) markets, sells, and loans all evaluation boards, kits, and/or modules (EVMs) pursuant to, and user expressly acknowledges, represents, and agrees, and takes sole responsibility and risk with respect to, the following: 1.
- Page 15 RADIO FREQUENCY REGULATORY COMPLIANCE INFORMATION FOR EVALUATION MODULES Texas Instruments Incorporated (TI) evaluation boards, kits, and/or modules (EVMs) and/or accompanying hardware that is marketed, sold, or loaned to users may or may not be subject to radio frequency regulations in specific countries.
- Page 16 Les types d'antenne non inclus dans cette liste, ou dont le gain est supérieur au gain maximal indiqué, sont strictement interdits pour l'exploitation de l'émetteur. Mailing Address: Texas Instruments, Post Office Box 655303, Dallas, Texas 75265 Copyright © 2014, Texas Instruments Incorporated spacer Important Notice for Users of EVMs Considered “Radio Frequency Products”...
- Page 17 IMPORTANT NOTICE Texas Instruments Incorporated and its subsidiaries (TI) reserve the right to make corrections, enhancements, improvements and other changes to its semiconductor products and services per JESD46, latest issue, and to discontinue any product or service per JESD48, latest issue.
-
Page 18: Ina210-215Evm Pcb
Mouser Electronics Authorized Distributor Click to View Pricing, Inventory, Delivery & Lifecycle Information: Texas Instruments INA210-215EVM...
Need help?
Do you have a question about the INA210-215EVM and is the answer not in the manual?
Questions and answers