EWM Phoenix Expert drive 4L M3.70 Operating Instructions Manual page 4

Contents
Notes on the use of these operating instructions
5.7.5
5.7.6
5.7.7
5.7.8
5.7.9
5.7.10
5.7.11
5.7.12
5.7.13
5.7.14
5.7.15
5.8 TIG welding .................................................................................................................................. 53
5.8.1
5.8.2
5.8.3
5.8.4
5.8.5
5.8.6
5.9 MMA welding ................................................................................................................................ 60
5.9.1
5.10 Remote control ............................................................................................................................. 62
5.11 Interfaces for automation ............................................................................................................. 62
5.11.1
5.12 Special parameters (advanced settings) ...................................................................................... 64
5.12.1
5.12.2
5.12.3
5.13 Machine configuration menu ........................................................................................................ 75
5.13.1
5.13.2
5.13.3
6 Maintenance, care and disposal ......................................................................................................... 79
6.1 General......................................................................................................................................... 79
6.2 Maintenance work, intervals ........................................................................................................ 79
6.2.1
6.2.2
6.2.3
4
MIG/MAG operating point ............................................................................................. 40
5.7.5.1 Selecting the display unit............................................................................... 40
5.7.5.2 Operating point setting using material thickness .......................................... 40
5.7.5.3 Arc length correction setting .......................................................................... 41
5.7.5.4 Accessory components for operating point setting ....................................... 41
MIG/MAG welding data display .................................................................................... 41
Conventional MIG/MAG Welding (GMAW non synergic) ............................................. 42
5.7.7.1 Setting the operating point (welding output).................................................. 42
forceArc / forceArc puls ................................................................................................ 43
rootArc/rootArc puls ...................................................................................................... 44
MIG/MAG program sequence ("Program steps" mode) ............................................... 45
5.7.10.1 Selecting the program sequence parameters using wire feed unit
control M3.70 ................................................................................................. 45
5.7.10.2 MIG/MAG overview of parameters, M3.70 .................................................... 46
Main program A mode .................................................................................................. 47
MIG/MAG automatic cut-out ......................................................................................... 47
Standard MIG/MAG torch ............................................................................................. 48
MIG/MAG special-torches............................................................................................. 48
5.7.14.1 Program- and Up- / down operation .............................................................. 48
5.7.14.2 MIG/MAG Push/Pull welding torch ................................................................ 49
5.7.14.3 Pin assignment .............................................................................................. 49
5.7.14.4 Switching between Push/Pull and intermediate drive ................................... 50
Expert menu (MIG/MAG) .............................................................................................. 51
5.7.15.1 Selection ........................................................................................................ 51
Welding torch connection ............................................................................................. 53
Welding task selection .................................................................................................. 54
TIG arc ignition ............................................................................................................. 55
5.8.3.1 Liftarc ignition ................................................................................................ 55
TIG automatic cut-out ................................................................................................... 55
TIG arc ignition ............................................................................................................. 56
5.8.5.1 Liftarc ignition ................................................................................................ 56
Pulses, function sequences .......................................................................................... 56
5.8.6.1 Explanation of signs and functions ................................................................ 56
Welding task selection .................................................................................................. 60
5.9.1.1 Setting using the stick electrode diameter .................................................... 60
5.9.1.2 Arcforce ......................................................................................................... 61
5.9.1.3 Hotstart .......................................................................................................... 61
Remote control connection socket, 19-pole ................................................................. 63
Selecting, changing and saving parameters................................................................. 65
Reset to factory settings ............................................................................................... 67
The special parameters in detail ................................................................................... 68
Selecting, changing and saving parameters................................................................. 75
Matching the cable resistance ...................................................................................... 77
Power-saving mode ...................................................................................................... 78
Daily maintenance tasks ............................................................................................... 79
6.2.1.1 Visual inspection ........................................................................................... 79
6.2.1.2 Functional test ............................................................................................... 79
Monthly maintenance tasks .......................................................................................... 80
6.2.2.1 Visual inspection ........................................................................................... 80
6.2.2.2 Functional test ............................................................................................... 80
Annual test (inspection and testing during operation) .................................................. 80
099-004846-EW501
8.01.2014