Specifications The Mira MyLine is a thermostatic mixer which Pressures has separate flow and temperature controls. Temperatures The Mira MyLine is an exposed valve with an Thermostatic Shut-down integral slidebar and hose to a 360 Showerhead. Connections Dimensions The thermostatic mixer incorporates a wax...
SAFETY WARNINGS thermostatic mixer. Make sure that there is sufficient headroom and ceiling clearance to Mira thermostatic mixers are precision engineered install the integral slidebar and Showerhead. and should give continued safe and controlled 10. When this product has reached the end of its...
Tick the appropriate boxes to familiarise yourself with the part names and to confirm that all of the parts are included. Mira MyLine Mixer Mira MyLine Shower Fittings 1 x Concealing Plate 1 x Wall Plugs 1 x Thermostatic Mixer...
SPECIFICATIONS Cold Pressures • Max Static Pressure: 10 Bar. • Max Maintained Pressure: 5 Bar. • Min Maintained Pressure (Gravity System): 0.1 Bar (0.1 bar = 1 Metre head from cold tank base to showerhead outlet). Note! For gravity fed / other low pressure systems (0.5 bar or below) remove the outlet flow regulator.
6. Decide on a suitable position for the Mixer, INSTALLATION make sure that there is sufficient headroom and ceiling clearance to install the integral Suitable Plumbing Systems slidebar rail and Showerhead. The position of the Mixer and the Shower Gravity Fed: Fittings must provide a minimum gap of 25 mm The thermostatic mixer must be fed from a cold between the spill-over level of the shower tray/...
Installing the Thermostatic Mixer Concealing 1. The thermostatic mixer must be fitted vertically Backplate Plate as illustrated and can only be installed with rear supply inlets. The supply pipework must be connected as follows: Inlet Nuts • Cold to Top Inlet •...
Page 9
6. For solid walls drill the fixing holes for the 11. Make sure that the concealing plate (with backplate with a 6 mm drill and insert the the hole at the bottom) is loosely fitted over wall plugs (supplied). For other types of wall the mixing valve inlets and align the mixer structure alternative fixings may be required with the inlet nuts.
13. Important! A 12 litre/minute flow regulator is COMMISSIONING fitted inside the outlet This can be removed for gravity fed / other low pressure systems Maximum Temperature Setting (0.5 bar or below). Before using the shower the maximum temperature must be checked to make sure that it is at a safe level.
Installing the Shower Fittings 3. Temporary install the slidebar assembly into the thermostatic mixing valve. Install the hose retaining ring, clamp bracket and the slidebar support onto the slidebar. 4. Using the wall bracket as a guide, mark the Note! Some components may already be position of the bottom fixing hole for the wall pre-assembled.
Page 12
7. Install the wall bracket and fully tighten the 10. Pass it through the hose retaining ring and fixing screw. install the showerhead onto the hose. Note! The slot in the wall bracket allow for Note! Ensure that the sealing washers are minor adjustment.
Height Adjustment OPERATION The height of the showerhead is easily adjusted by Flow Control gently moving the clamp bracket either up or down the slide bar until the required height is achieved. Turn the flow lever anticlockwise to the maximum flow.
Page 14
Changing the Spray Setting The 360 Showerhead has four different spray actions:- Rain, Cloud, Storm and Burst. The showerhead features a rotating head to enable differing spray patterns to be achieved, turn the showerhead in the direction shown to activate the different spray patterns. Rain Cloud Burst...
Lubricants USER MAINTENANCE Silicone based lubricants must only be used on If you require a Mira trained service engineer or the rubber seals. agent, refer to section: ‘Customer Services’. Caution! Oil based or other lubricant types may cause rapid deterioration of seals.
Spray Plate Assembly Cloud Spray Plate Assembly 1. Use a suitable tool to remove the grommets. This product is supplied configured for the majority of showering systems including electric 2. Using the 2.5 mm hexagonal wrench showers. (supplied), remove the screws. 3.
ACCESSORIES Genuine Mira accessories can be purchased direct from Customers Services (our contact details can be found on the back cover of this guide) or from approved stockists or merchants. Eco Showerhead Everclear Showerhead Wall Mounted Soap Dish White - 2.1668.001 White - 2.1616.030 White - 1.1540.278 Chrome - 2.1668.002...
fi lters) or where no fault has been found with guarantee period and beyond. You have the assurance of a the product. fully trained Mira Technician, genuine Mira spare parts and Water or electrical supply, waste and isolation issues. a 12 month guarantee on any chargeable work done.