Related Manuals for Linear AccessKey
Summary of Contents for Linear AccessKey
- Page 1 Digital Keyless Entry System Installation and Programming Instructions (760) 438-7000 • FAX (760) 438-7043 USA & Canada (800) 421-1587 & (800) 392-0123 Toll Free FAX (800) 468-1340 www.linearcorp.com...
-
Page 2: Table Of Contents
Form “C” 1 Amp @ 24 Volts maximum ACCESSKEY OPERATION ..... . 10 Solid state outputs (Outputs #3 & #4) MANAGER’S ENTRY CODE LOG . -
Page 3: Component Locations
TACTILE REDUCE TERMINAL BLOCK J4 KEYPAD BEEPER SOUND POWER AND INPUTS KEYLOCK Figure 1. Component Locations WIRING DIAGRAM TYPICAL GATE INSTALLATION WIRING TYPICAL DOOR INSTALLATION WIRING ACCESSKEY ACCESSKEY N.O. N.O. COMMON COMMON RELAY #1 RELAY #1 TO ALARM N.C. N.C. -
Page 4: Installation
Use four security bolts and locking nuts to secure the keypad’s backplate to the pedestal (see Figure 3). Wall Mounting The AccessKey keypad can be mounted directly to a wall or flat surface. Use the appropriate fasteners to secure the keypad’s backplate to the mounting surface. - Page 5 2 WIRES FOR FOR DOOR (BEHIND GATE) REQUEST-TO-ENTER SENSE FIRE ACCESS KEYSWITCH ACCESSKEY KEYPAD 2 WIRES POWER 2 WIRES FROM ACCESSKEY 2 WIRES FROM OPERATOR TO TRIGGER GATE OPEN FOR ACCESSKEY POWER FROM ELECTRIC 2 WIRES POWER DOOR FOR DOOR SUPPLY STRIKE STRIKE Figure 5.
-
Page 6: Factory Defaults
LED will blink. This number, i.e. 0001) do not need to be entered when indicates that the AccessKey is ready to accept the new programming a new entry code. The AccessKey will programming data. After the new data entry is complete, internally add any zeros to fill all digits determined the green LED will light while the data is being stored. -
Page 7: Programming Options
When programmed for DOOR SENSE, if an open condition PROGRAMMING OPTIONS on the input occurs before access is granted (with an entry There are several AccessKey programming options. For code or with the request-to-enter input) a FORCED most installations, the factory set default options are ENTRY output will occur. - Page 8 Default: 2 Seconds ! CAUTION: Performing a master reset will clear Sets the length of time Output #4 activates when triggered. the entire memory of the AccessKey and return Press: 2 4 Seconds all programmable options to the factory default values.
- Page 9 (see Figure 9). These outputs can be used to activate indicators or sounders. See Figure 7 for wiring examples using the solid state outputs. ACCESSKEY POWER ELECTRONIC BEEPER 1K Ω 1K Ω...
-
Page 10: Accesskey Operation
ACCESSKEY OPERATION Users of the AccessKey have up to 40 seconds to key in their entry code. Up to eight seconds are allowed between each keystroke. All digits of the entry code must be entered. Example: If the code is 0042, the user must enter “0 0 4 2”. -
Page 11: Manager's Entry Code Log
MANAGER’S ENTRY CODE LOG NAME ADDRESS OR APARTMENT NUMBER ENTRY CODE RELAY NUMBER ◊ ◊ ◊ ◊ ◊ ◊ ◊ ◊ ◊ ◊ ◊ ◊ ◊ ◊ ◊ ◊ ◊ ◊ ◊ ◊ ◊ ◊ ◊ ◊ ◊ ◊ ◊ ◊... -
Page 12: Linear Limited Warranty
Warranty Expiration the user is encouraged to try to correct the interference by Date as labeled on the product. This Linear Corporation one or more of the following measures: Warranty is in lieu of all other warranties express or °...
Need help?
Do you have a question about the AccessKey and is the answer not in the manual?
Questions and answers