Wiznet WizFi630 Serial Command Manual
  1. Manuals
  2. Brands
  3. Wiznet Manuals
  4. Control Unit
  5. WizFi630
  6. Serial command manual

Wiznet WizFi630 Serial Command Manual

Hide thumbs Also See for WizFi630:
Table of Contents

Advertisement

Quick Links

Download this manual See also: User Manual
Serial Command Guide
This document describes usages for WizFi630 WIFI AP Module. Descriptions scope and
boundary is limited as bellows
 Testing environments
 Networks operation mode
 Serial operation Modem
 Supplied software usages
 Serial command definition
☞ For more information, visit our website at
For
WizFi630 Users
(Version 1.0)
©2012 WIZnet Co., Ltd. All Rights Reserved.
http://www.wiznet.co.kr

Advertisement

Table of Contents
loading

Related Manuals for Wiznet WizFi630

Summary of Contents for Wiznet WizFi630

  • Page 1 Serial Command Guide WizFi630 Users (Version 1.0) This document describes usages for WizFi630 WIFI AP Module. Descriptions scope and boundary is limited as bellows  Testing environments  Networks operation mode  Serial operation Modem  Supplied software usages  Serial command definition ©2012 WIZnet Co., Ltd.

  • Page 2: Table Of Contents

    Table of contents 1. TEST ENVIRONMENT SETUP ................. 1 System Setup..............................1 WizFi630’s default serial configuration....................1 PC #3 Setup..............................1 PC #1 and PC#2 Serial Setup........................1 2. SIMPLE SERIAL COMMAND AT SERIAL TERMINAL PROGRAM ... 2 3.

  • Page 3: Test Environment Setup

    1. Test Environment Setup 1.1 System Setup <WizFi630> 802.11 b/g/n WIFI AP Module <PC#1> Serial Terminal Program running and connected to WizFi630’s Serial Port #1 <PC#2> Serial Terminal Program running and connected to WizFi630’s Serial Port #2 <PC#3> TCP Server application is running 1.2 WizFi630’s default serial configuration.

  • Page 4: Simple Serial Command At Serial Terminal Program

    2. Simple serial command at serial terminal program ① <RF> This command gets module’s firmware version and normally used to check module is working or not ② <ATDT> This command changes module’s “serial working mode” as data mode This is special command so do not type each character and <ATDT> copy and paste it at terminal program.

  • Page 5: Wizsmartscript For Wizfi630

    3. WIZSmartScript for WizFi630 3.1 Run Program ① If you run the WIZSmartScript program, you can see the KEY Confirm Dialog as shown below. ② If you enter the received CODE and KEY, you can operate the program in normal mode.

  • Page 6: Get Basic

    ① Input the COM port of PC and baud rate. (Default Baud Rate : 38400) ② Select “WizFi630” for Model, “A. Get Basic” for Group and “1. Get Module Information” for Script. ③ If you click “Start Script”, you can see the basic information of WizFi630 as below.
  • Page 7 B. Get Network Information ① Select “WizFi630” for Model, “A. Get Basic” for Group and “2. Get Network” for Script. ② If you click “Start Script”, you can see the network information of WizFi630 as below.
  • Page 8 C. Get Wireless Information ① Select “WizFi630” for Model, “A. Get Basic” for Group and “3. Get Wireless” for Script. ② If you click “Start Script”, you can see the wireless information of WizFi630 as below.
  • Page 9 D. Get Wireless(Client) Information ① Select “WizFi630” for Model, “A. Get Basic” for Group and “4. Get Wireless (Client)” for Script. ② If you click “Start Script”, you can see the wireless(Client) information of WizFi630 as below.
  • Page 10 E. Get Wireless(AP-Client) Information ① Select “WizFi630” for Model, “A. Get Basic” for Group and “5. Get Wireless (Client-AP)” for Script. ② If you click “Start Script”, you can see the wireless(AP-Client) information of WizFi630 as below.
  • Page 11 F. Get Serial Information ① Select “WizFi630” for Model, “A. Get Basic” for Group and “6. Get Serial” for Script. ② If you click “Start Script”, you can see the serial information of WizFi630 as below.

  • Page 12: Functions

    ① Input the COM port of PC and baud rate. (Default Baud Rate : 38400) ② Select “WizFi630” for Model, “B. Functions” for Group and “1. Site Survey” for Script. ③ If you click “Start Script”, WizFi630 will find the APs and you can see the process as below.
  • Page 13 B. Restart ① Select “WizFi630” for Model, “B. Functions” for Group and “2. Restart” for Script. ② If you click “Start Script”, WizFi630 will reboot and you can see the process as below.
  • Page 14 C. Factory Default ① Select “WizFi630” for Model, “B. Functions” for Group and “3. Factory Default” for Script. ② If you click “Start Script”, WizFi630 will reset to factory default and you can see the process as below.
  • Page 15 ① Select “WizFi630” for Model, “B. Functions” for Group and “4. Send 6xx Command” for Script. ② Enter the valid value into the blank field. ③ If you click “Start Script”, WizFi630 will send the user command and you can see the process as below.

  • Page 16: Set Operation Mode

    A. Access Point Mode ① Input the COM port of PC and baud rate. (Default Baud Rate : 38400) ② Select “WizFi630” for Model, “C. Set operation Mode” for Group and “1. Access Point Mode” for Script. ③ If you click “Start Script”, you can see the process as below.
  • Page 17 B. Gateway Mode ① Select “WizFi630” for Model, “C. Set operation Mode” for Group and “2. Gateway Mode” for Script. ② If you click “Start Script”, you can see the process as below.
  • Page 18 ② Enter the valid value into the SSID and Key field. ③ Enter the valid value into the IP and Gateway field. ④ If you click “Start Script”, WizFi630 will associate to the AP with DHCP and you can see the process as below.
  • Page 19 ① Select “WizFi630” for Model, “C. Set operation Mode” for Group and “4. Client Mode(WPA, DHCP)” for Script ② Enter the valid value into the SSID and Key field. ③ If you click “Start Script”, WizFi630 will associate to the AP with static IP and you can see the process as below.

  • Page 20: Set Serial

    A. TCP Server(5000) ① Input the COM port of PC and baud rate. (Default Baud Rate : 38400) ② Select “WizFi630” for Model, “D. Set Serial” for Group and “1. TCP Server(5000)” for Script. ③ If you click “Start Script”, you can see the process as below.
  • Page 21 B. TCP Client(192.168.16.101-5000) ① Select “WizFi630” for Model, “D. Set Serial” for Group and “2. TCP Client(192.168.16.101-5000)” for Script. ② If you click “Start Script”, you can see the process as below.

  • Page 22: Serial Command Definitions

    4. Serial command definitions E. Serial command is fully described at the file named ”WizFi630 Serial Command list.xlsx” and “WizFi630 Serial Command list.pdf Last Modified : 2011-11-16 Contents Command Syntax Contents Item Version <RF> Get Firmware Version <RA> Get MAC address module Address <RI>...
  • Page 23 <RQ> when protocol is TCP available (Main Port connection status) <RY> when protocol is TCP available (Aux Port connection status) Close TCP connection <WC> (Main/Aux Port) Close TCP connection <WQ> (Main Port) Close TCP connection <WY> (Aux Port) System <QZ> Status Current System status for flash access <QN>...
  • Page 24 <GRxx> 20MHz: 7,14.5,21.5,28.5,43.5,57.5,65,72, Set Data Rate 40MHz: 15,30,45,60,90,120,135,150, Client/Adhoc Mode: Not Support b only: 1, 2, 5, 11 g only, bg mode: 1, 2, 5, 6, 9, 11, 12, 18, 24, 36, 48, 54 Get Hidden SSID <DH> Client/Adhoc Mode: Not Support Broadcast SSID <GHx>...
  • Page 25 Checking Get Profile Get Profile <DF> Available at Client/Adhoc Mode <Sx_x_x_x_x_x_x> add/del_SSID_Channel_AuthMode_E ncrypt_KeyId_Key add/del: 1(add), 0(delete) SSID: profile 의 SSID Set WIFI Profile AuthMode: 1(Open), 3(Shared), Set Profile Add WIFI profile and make it activate 5(WPA-PSK), 7(WPA2-PSK) Available at Client/Adhoc Mode Encrypt: 0(None),1 (WEP), 2(TKIP), 3(AES) KeyId: 1-4, WPA-PSK/WPA2-...
  • Page 26 <GUx_x_x_x_x_x_x_x> AuthMode_Encrypt[_DefaultKey_Ke yLength_KeyFormat_KeyValue_radiu sPasswd_radiusIP_radiusPort] AuthMode: 1(Open), 2(802.1x), 3(Shared), 4(WPA), 5(WPA-PSK), 6(WPA2), 7(WPA2-PSK), 8(WEPAUTO), 9(WPA1WPA2), Change Security. It takes time min : 4 , mac 10 Security a(WPAPSKWPA2PSK) seconds Control Encrypt: 0(None),1 (WEP), 2(TKIP), Client/Adhoc Mode: Not Support 3(AES), 4(TKIP_AES) KeyLength: 0(None), 1(WEP64), 2(WEP128) DefaultKey: 1 - 4 KeyFormat(WEP): 0(Ascii), 1(Hex)
  • Page 27 Connection <OU> Option <OU> 0: TCP Client Mode, Serial to LAN Set TCP Connection Option auto connection 1: TCP Client Mode, Serial to LAN connection made in serial date in <RO> Get Main Port Status <WOx_x_x_a.b.c.d_x> Enable[_Protocol_Mode_ServerIP or Domain_ServerPort] Enable: 0(Disable), 1(Enable), Disable Main Port ( In disable, other data is ignored...

  • Page 28: Accessing Module Via Web Browser

    Already configed with same data 5. Accessing module via Web Browser F. All of control is done via web ① Connect your PC to WizFi630 EVB via LAN or WIFI ② Set your PC IP address Auto ③ Run Web Browser ④...

  • Page 29: More Information

    6. More information  Website : www.wiznet.co.kr  WizFi630-User Manual (software user manual)  WizFi630 Data Sheet  WizFi630 Series Application Notes  WizFi630 Serial Command Definitions...

Table of Contents