Page 2
Certification Information CE for Class B ITE INFORMATION TO THE USER Hereby, WIZnet. Declares that this WizFi630 is in compliance with the essential requirements and other and other relevant provisions of directive 1999/5/EC. relevant provisions of directive 1999/5/EC WARNING: This is a class B product. In a domestic environment this product may cause radio...
Therefore, WizFi630 can be the best solution for users who lack wireless network experience. WizFi630 follows the 802.11b/g/n standard and support up to 150Mbps speed in wireless interface. WizFi630 provides a test board, pc software, and documents so that anyone can develop a wireless solution.
In this mode, all Ethernet ports and the wireless interface are bridged together. Wired/Wireless interface has the same IP address space with its top mesh. DHCP Server function is disabled and WizFi630 does not assign an IP. Wireless (LAN Port included) sending periodic Broadcast Packet to Station and maintains a connection with Station.
Wireless I/F is assigned as WAN Port and all Ethernet Ports are bound to LAN Port. Set the profile and the WizFi630 is automatically connected to the AP when re-booting in the future. Devices that are connected through the LAN port are assigned a private IP. WizFi630 periodically sends PING Packet to AP Gateway and maintains connection with AP.
Wireless I/F is assigned as WAN Port and all Ethernet Ports are bound to LAN Port. This mode is similar to Station mode, however the difference is that the Wireless I/F will operate as client with AP simultaneously. WizFi630 periodically sends Broadcast Packet to Sub-LAN (LAN Port included) and maintains connection with Station.
2.3. Internet Setting 2.3.1. Internet connection setting Select the internet service type and WizFi630 can connect to the internet If users would like access to Internet, Gateway Mode should be selected. Type Description Select the communication ways for Internet’s connection...
2.3.2. Local network setting WizFi630 internal IP setting, DHCP server setting and DHCP. Type Description Enter the module’s IP. (Default Value : 192.168.16.254) IP Address Enter the module’s subnet mask. Subnet Mask MAC Address of module’s LAN port (Wireless included). (Read Only) MAC Address Decide whether the module’s DHCP server will be used.
2.4.6. Wireless network status The status of the station that is connected to WizFi630 is shown. The surrounding wireless AP’s status are shown. Type Description Channel Channel information of AP SSID SSID of AP BSSID MAC address of AP Security...
Enable Power Saving function or not. Enable Direct Link function or not. Direct Link Setup In order to use Direct Link function, the AP connected to WizFi630 and the Station to be connected must support Direct Link function. MAC Address Enter the MAC Address of the station to be connected using direct link function.
Serial to LAN operation mode. ( Client Mode recommended) - Server : waits for connection. Mode - Client : connected to the remote server of WizFi630 - Mixed : not recommended Server IP Enter the IP address for WizFi630 setting.
Type Description Status Enable or disable this option (Checked : Enable, Un-Check : Disable) Before sending data from Main port to serial port, WizFi630 added a TAG in the front of payload. Main Port For example: In-come LAN Data : “abcdegf”...
2.6.2. Port forwarding When a computer on the internet sends data to the external IP address of the router (WizFi630), the router (WizFi630) needs to know what to do with the data. Port Forwarding simply tells the WizFi630 which computer on the local area network to send the data to. When you have port forwarding rules set up, your router takes the data off of the external IP address:port number and sends that data to an internal IP address:port number.
2.6.3. Packet filtering WizFi630 can accept or block Internet packets according to pre-defined MAC or IP address First, please do the basic settings Type Description Source MAC Pre-defined source MAC address for MAC filtering function Dest IP Address Destination IP address...
2.6.5. System Security Defense from external attack. Type Description Remote management Settings about accessing methods from WAN to WizFi630’s embedded web server Telnet management Settings about accessing methods from WAN to WizFi630’s telnet Ping from WAN Filter Disable/Enable the WizFi630’s Ping response...
To use DynDNS, users should go to www.dyndns.org to create user name and domain name. And then, set related configurations by using WizFi630’s webpage. Similarly, to use freeDNS zoneedit, or no-ip,users should go to their homepage first to create user name and domain name.
2.7.3. Config Settings Save the setting value of WizFi630 to the PC. Type Description Export Settings The setting files from the PC file are applied to the module. Import Settings The system’s setting information is saved as a file in the PC.
WIZnet assumes no responsibilities or liabilities for the use of any of its products, conveys no license or title under any patent, copyright or mask work rights to these products, and makes no representations or warranties that these products are free from patent, copyright or mask work infringement, unless otherwise specified.