Test Settings (H/W) .......................... 1 1.3. Test Settings (S/W) ........................... 2 1.4. Connection Check ..........................3 1.5. Connecting the Web page of WizFi630 .................. 4 1.5.1. Web address ..........................4 1.5.2. Web Login ..........................4 Demonstration & Test ....................6 2.1.
1. How to connect to administration web page This chapter will explain about the basic settings for connecting to the administration web page. The content of this chapter is based on WizFi630-EVB for evaluation of WizFi630. 1.1. Configuration of WizFi630-EVB 1.2.
Connect the Ethernet port of WizFi630-EVB with the hub. Connect the PC with the hub. 1.3. Test Settings (S/W) Please use the following WizFi630 network setting for the user’s PC network setting. WizFi630 IP Address: 192.168.16.254 IP Address: 192.168.16.XXX Gateway: 192.168.16.1 Gateway: 192.168.16.1...
255.255.255.0 and click “Add” again. 1.4. Connection Check After the test setting is done, check the connection between WizFi630 and the PC using ping test. Click Start -> Run and enter cmd. Enter ping 192.168.16.254 when the CMD window opens.
The following processes may vary depending on the user’s version. 1.5.1. Web address Open a web browser on user’s PC. Input the default IP address of WizFi630, “192.168.16.254” and click Enter. 1.5.2. Web Login A pop up will request user to input User ID and Password User ID: admin / Password: admin (WIZnet Co., Ltd.)
Page 8
The system’s basic information, as shown below, will appear if successfully authenticated.. Type Description F/W Version The firmware version of WizFi630 is displayed. System Up Time System up time displayed. Operation Mode System operation mode displayed. Internet Configuration Information of the external network is displayed.
Environment for Serial to Wi-Fi Test This section will explain on how to set Wizfi630 in AP mode and test Serial to Ethernet. Connect WizFi630 and <PC1> with RS-232 and LAN cable as shown below; set the operation mode as AP mode, and start the TCP server.
(We recommend directly connecting <PC1> and WizFi630 instead of using hub). Check the operation mode of WizFi630; select AP mode in case of other mode is being used. Set the serial settings of the WizFi630 to TCP server as shown below.
2.1.3. <PC 2> Settings Connect the network for WizFi630 < Default SSID : WLAN-AP > Retrieve the IP address of WizFi630 and ping test. If the ping test is successful, the network is connected. (WIZnet Co., Ltd.) WizFi630 Quick Start Guide...
2.1.4. Comunication Test of WizFi630 Open <PC1>’s serial program, enter the serial configuration value, and click ‘open.’ < Serial Program: Device Terminal Ver. 1.0 > Open <PC2>’s TCP/IP program, enter the IP address of the TCP server (192.168.16.254), and click ‘connect.’ < TCP/IP Program : Device Terminal Ver. 1.0 >...
Environment for Serial to Wi-Fi Test This section will explain on how to set WizFi630 in client mode and test Serial to Ethernet. Connect WizFi630 and <PC1> with RS-232 and LAN cable as shown below; set the operation mode as Client mode, and start the TCP server.
Enter 192.168.16.254 in <PC1> web browser and connect to the administration web page. (We recommend directly connecting <PC1> and WizFi630 instead of using hub). Check the operation mode of WizFi630; select Client (Station) mode in case of other mode is being used.
Page 15
Attempt connection with surrounding AP in the Station Site Survey menu. < SSID : belkin54g > (WIZnet Co., Ltd.) WizFi630 Quick Start Guide...
Page 16
The WAN IP address below is the IP address assigned from AP. Set the serial settings for WizFi630 to TCP server as shown below. (Check the Server Port, Baud rate, Data bits, Parity, Stop bits, and Flow control) (WIZnet Co., Ltd.)
2.2.3. <PC 2> Settings Connect to AP. < Ex) belkin54g > Retrieve the IP address of WizFi630 and ping test. If the ping test is successful, the network is connected. ( WizFi630’s IP Address : 192.168.1.7 ) (WIZnet Co., Ltd.)
2.2.4. Communication Test of WizFi630 Open <PC1>’s serial program, enter the serial configuration value, and click ‘open.’ < Serial Program : Device Terminal Ver. 1.0 > Open <PC2>’s TCP/IP program, enter the IP address of the TCP server (192.168.1.7), and click ‘connect.’...