Technical Specifications; Troubleshooting - STEINEL XLED home 2 Information

The warranty shall not cover damage to wear parts,
damage or defects caused by improper treatment
or maintenance. Further consequential damage to
other objects shall be excluded.
Claims under the warranty will only be accepted
if the unit is sent fully assembled and well-packed
with a brief description of the fault, a receipt or
invoice (date of purchase and dealer's stamp) to
the appropriate Service Centre.
Service
Our Customer Service Department will repair faults
not covered by the warranty or after the warranty
period has expired. Please send the product well-
packed to your nearest Service Centre.
11� Technical specifications
Dimensions (H × W × D) 194 × 180 × 161
Output 14.8 W / 80 lm/W
Luminous flux / brightness 1184 lm
Weight 0.575 kg
Area illuminated Front view 283.1 cm
Mains current 75 mA
Power factor max. 100 W (resistive load, e.g. light bulbs)
max. 500 W (uncorrected, inductive, cos
max. 4 × 56 W, C ≤ 88 μF
Efficiency 80 lm/W
Colour temperature 4000 K (neutral white)
Colour rendering index Ra ≥ 80
Supply voltage 230-240 ~V / 50/60 Hz
Sensor system Passive infrared
Reach max. 14 m via control dial
Angle of coverage 140°
Time setting 3 min factory setting / 1 s to 15 min with the app
Twilight setting 2-2000 lux via control dial and with the app
IP / protection class IP44 / II
Z-Wave wireless range approx. 100 m (unobstructed line of vision)
Radio frequency band 868 MHz
Transmitter power ≤ 2.5 mW
Side view 113 cm
2 2
= 0.5, e.g. fluorescent lamps)
– 16 –
12� Troubleshooting
Malfunction Cause
Sensor-switched LED floodlight
Fuse faulty; not switched ON;
without power
break in wiring
Short-circuit
Sensor-switched LED floodlight
Twilight setting in night-
will not switch ON
time mode during daytime
operation
Mains switch OFF
Fuse faulty
Detection zone not correctly
adjusted
Sensor-switched LED floodlight Continued movement within
will not switch OFF the detection zone
Sensor-switched LED floodlight
Animals moving in detection
keeps switching ON and OFF
zone
Sensor-switched LED floodlight Wind is moving trees and
switches ON when it should not bushes in the detection zone
Cars in the street are detected
Sudden temperature changes
due to weather (wind, rain,
snow) or exhaust air from fans
or open windows
Sensor-switched LED
floodlight swaying (moving),
resulting, for example, from
gusts of wind or heavy
precipitation
The device cannot be added Z-Wave controller too far from
(and is not yet added) the device
The device cannot be added It is already added
Status-LED flashing for
No wireless contact with the
1 second every 5 seconds
Smart Friends Box or other
Z-Wave controller
Status LED flashing rapidly
Critical fault
all the time
Remedy
New fuse, turn on power switch,
check wiring with voltage tester
Check connections
Reset
Switch ON
Replace fuse, check connection if
necessary
Readjust
Check zone and readjust if
necessary or apply shroud
Tilt sensor higher or apply specific
shrouds; adjust detection zone or
fit shrouds
Change detection zone
Change detection zone
Adjust detection zone or install in
a different place
Fit sensor-switched LED flood-
light to a firm surface
Reduce distance from Z-Wave
controller
Install a Z-Wave repeater
Remove device from existing
network
Carry out default reset
Re-start Smart Friends Box or
Z-Wave controller
Reduce distance from Z-Wave
controller
Install a Z-Wave repeater
Briefly disconnect device from the
mains power supply
– 17 –